EVO Nano Series User Manual
Table Of Contents
- User Manual
- EVO Nano Series
- Terms for Usage
- Trademark Information
- Copyright
- Disclaimer
- Data Storage and Use
- Table of contents
- Chapter 1 Read Instructions
- Chapter 2 Aircraft
- ① Propeller
- ④ Forward visual system
- ② Motor
- ⑤ Antenna
- ③ PTZ camera
- ⑥ Rear vision system
- ⑨ USB-C port
- ⑦ Power button
- ⑩ Rear LED indicator
- ⑧ Aircraft battery
- ⑪ SD card slot
- ⑫ Air outlet
- ⑬ Ultrasonic sensor
- ⑮ Air inlet
- ⑭ Downward vision system
- There is an LED indicator on the tail of the aircr
- Status Definition of Flight LED Indicator
- Back LED Indicator
- Meaning
- Normal status
- Green light flashes slowly (1 flash every 2 second
- Aircraft in GPS mode
- Yellow light flashes slowly (1 flash per second)
- Aircraft in ATTI mode
- Pairing
- Green light flashes quickly
- Aircraft and remote controller are pairing
- Green light stays on for 5 seconds
- Pairing successful
- Red light stays on for 5 seconds
- Pairing failed
- Compass calibration
- Yellow light is on
- Starting compass calibration
- Yellow light is on
- Calibration failed
- Green light is on
- Calibration successful
- Warning
- Yellow light flashes slowly (1 flash per second)
- Low battery warning
- Red light flashes slowly (1 flash per second)
- Critical low battery alert
- Updating
- Green light flashes quickly
- Aircraft is updating
- Green light is is on
- Update successful
- Yellow light flashes slowly (1 flash per second)
- Update failed
- The battery for EVO Nano is 2250mAh and has the ra
- The battery indicator is divided into LED 1, LED 2
- Chapter 3 Remote controller
- Chapter 4 Autel Sky App
- Chapter 5 Flight
- 1) As shown in figure, press the left and right st
- 2) Slowly push up the left stick.
- 1) Press and slide the one-click takeoff button (
- 2) The aircraft will automatically rise to the hei
- Class I: main airport & low-altitude area for mann
- Class II: Sensitive area or organization & militar
- Chapter 6 Maintenance and service
- Method 1: download firmware upgrade package from A
- Method 2: download firmware upgrade package from t
- Chapter 7 Technical Specification
Select an open and well-lit area (such as grass lawn) as the take-off point.
When the aircraft is ready for precise landing, it is necessary to ensure that the take-off
environment has no change.
2.6.3 Compass calibration
The compass has been calibrated in factory, with no need for calibration by user normally. If
the compass indicates the error information, or the flight direction of the aircraft is not
consistent with the control input, or the flight place is far from the calibrated distance, please
carry out the following calibration procedure.
Warning
The compass is very sensitive to the electromagnetic interference that may cause the
compass error and the flight quality reduction. If the company still fails to be used after
calibration, it is allowed to move the aircraft to other places for recalibration.
In the case of compass calibration, please pay attention to the following points:
Select an open outdoor area.
Keep away from the magnetic interference source, such as magnet or concrete
reinforcement. The calibration result may also be affected if close to a large structure.
Keep away from the underground and overhead power lines.
Never carry the ferromagnetic materials (such as key or magnetic ornaments) with you.
Keep away from all electronic devices (such as mobile device) that may interfere with
the calibration.
Calibration procedure:
1. Unfold the aircraft and open Autel Sky App and enter the menu setting interface, choose
the “safety” option, click the “compass calibration” to the calibration interface, and then click
the “start” key.