EVO Nano Series User Manual
Table Of Contents
- User Manual
- EVO Nano Series
- Terms for Usage
- Trademark Information
- Copyright
- Disclaimer
- Data Storage and Use
- Table of contents
- Chapter 1 Read Instructions
- Chapter 2 Aircraft
- ① Propeller
- ④ Forward visual system
- ② Motor
- ⑤ Antenna
- ③ PTZ camera
- ⑥ Rear vision system
- ⑨ USB-C port
- ⑦ Power button
- ⑩ Rear LED indicator
- ⑧ Aircraft battery
- ⑪ SD card slot
- ⑫ Air outlet
- ⑬ Ultrasonic sensor
- ⑮ Air inlet
- ⑭ Downward vision system
- There is an LED indicator on the tail of the aircr
- Status Definition of Flight LED Indicator
- Back LED Indicator
- Meaning
- Normal status
- Green light flashes slowly (1 flash every 2 second
- Aircraft in GPS mode
- Yellow light flashes slowly (1 flash per second)
- Aircraft in ATTI mode
- Pairing
- Green light flashes quickly
- Aircraft and remote controller are pairing
- Green light stays on for 5 seconds
- Pairing successful
- Red light stays on for 5 seconds
- Pairing failed
- Compass calibration
- Yellow light is on
- Starting compass calibration
- Yellow light is on
- Calibration failed
- Green light is on
- Calibration successful
- Warning
- Yellow light flashes slowly (1 flash per second)
- Low battery warning
- Red light flashes slowly (1 flash per second)
- Critical low battery alert
- Updating
- Green light flashes quickly
- Aircraft is updating
- Green light is is on
- Update successful
- Yellow light flashes slowly (1 flash per second)
- Update failed
- The battery for EVO Nano is 2250mAh and has the ra
- The battery indicator is divided into LED 1, LED 2
- Chapter 3 Remote controller
- Chapter 4 Autel Sky App
- Chapter 5 Flight
- 1) As shown in figure, press the left and right st
- 2) Slowly push up the left stick.
- 1) Press and slide the one-click takeoff button (
- 2) The aircraft will automatically rise to the hei
- Class I: main airport & low-altitude area for mann
- Class II: Sensitive area or organization & militar
- Chapter 6 Maintenance and service
- Method 1: download firmware upgrade package from A
- Method 2: download firmware upgrade package from t
- Chapter 7 Technical Specification
protection will be activated. The battery will automatically discharge to a safe level, and this
discharging process takes 2~3 days. In this period, it is normal that the battery may be slightly
hot.
2) Low battery protection: in the case of low battery level, the battery will automatically enter
sleep mode to avoid damage. Under this mode, there will be no reaction when pressing the
power button. To wake up the battery, it is allowed to connect it with charger.
3) Charging temperature protection: the battery will stop charging in the case of charging
temperature lower than 5ºC (41ºF) or higher than 45ºC (113ºF).
4) Overcurrent protection: the large charging current will seriously damage the battery, so the
battery will stop charging in the case of excessive charging current.
5) Overcharge protection: the battery will automatically stop charging after it is fully charged.
6) Balanced protection: each battery unit shall maintain voltage balance to avoid overcharge
or overdischarge.
7) Overdischarge protection: the battery will automatically disconnect the power output
function when it is not used and completes the self-discharge period. This function is disabled
in flight.
8) Short-circuit protection: the power supply will be disconnected once the short circuit is
detected.
9) Power-down mode: the battery will turn off if there is no operation within 30 minutes.
10) Communication: during use, the aircraft will be continuously synchronous with battery to
provide the real-time information, including voltage, capacity, current, and temperature.
11) Low power consumption mode: the battery will enter the low power consumption mode
when the battery level is lower than about 8% to reduce the own power consumption. To
recover the battery from the low power consumption mode, it shall be activated by charger.
2.3.3 Precautions
1. Use
Please be sure to turn off the aircraft power before installing or disassembling aircraft
battery.
It is only allowed to use the battery and charger sold or authorized by Autel Robotics for
EVO Nano series. The use of any unapproved battery or charger may cause fire,
explosion, leakage or other dangers. Autel Robotics will assume no responsibility for any
consequence of using the battery or charger of third party.