LIUDY2003_eng-00 Instruction Manual for the use and the maintenance of the Radio Remote Control Original instructions Part B: Conformity and frequencies (915-928MHz) DYNAMIC SERIES
WARNING THIS PART OF THE MANUAL CONSISTS OF Part B - Information, instructions and warnings for the Conformity and frequencies (915-928MHz). The Manual consists of Part A – General, Part B – Conformity and Frequencies, Part C – Transmitting Unit, Part D – Receiving Unit and Part E – Battery and Battery Charger, plus the Technical Data Sheet.
It is also the responsibility of the Manufacturer and of the design professionals of the Machine on which the Autec Radio Remote Control is to be installed and used to be certain that the structure, condition, organization and markings of the Machine as installed at the facility is appropriate for and will allow for the safe and reliable use and control of the Machine through the Autec Radio Remote Control interface.
IT IS THE RESPONSIBILITY OF THE OWNER AND FACILITY OPERATOR, AND THEIR OFFICERS, MANAGERS AND SUPERVISORS, to be certain that all Users of the Autec Radio Remote Control and that all Persons who are or will be working with or near the Machine operated by or through the Autec Radio Remote Control are fully and properly educated and trained by qualified Personnel in the proper and safe use of the Autec Radio Remote Control and of the Machine, including without limitation complete familiarity with and understa
INDEX 1 2 3 4 Information on the use of instructions ................................................................. 7 1.1 Structure of the Instruction Manual ................................................................. 7 1.2 Caption and terminology ................................................................................. 9 1.3 Symbols ......................................................................................................... 9 1.4 To whom the instructions are addressed .....
Information on the use of instructions 1 7 Information on the use of instructions Before reading this part of the Manual, you must read and understand the general part (Part A) of the Manual provided with the Radio Remote Control. 1.
Information on the use of instructions Usage and maintenance instructions are supplemented by the Radio Remote Control's Technical Data Sheet, that: -- describes the Transmitting Unit's configuration, -- indicates the relation between commands sent by the Transmitting Unit and those available on the Receiving Unit.
Information on the use of instructions 1.2 9 Caption and terminology Contact Autec if any of the instructions, symbols, warnings or images are not clear and understandable, or if you have doubts or questions.
1.4 Information on the use of instructions To whom the instructions are addressed Addressees of instructions are listed in the paragraph with the same title in the general part: please refer to that part. 1.5 Instruction storage Regulation for the storage of instructions are described in the paragraph with the same title in the general part: please refer to that part. 1.
Brief product presentation 2 Brief product presentation 2.1 Series, Radio Remote Control and Unit 11 This part of the Manual describes: -- the Dynamic series' Radio Remote Control compliance with the standards, the requirements and conditions of use in each Country and -- the different frequency bands, in which the Radio Remote Control is able to operate.
3 Conformity Conformity Addressees of instructions must: -- make sure that the Radio Remote Control works within the frequency band permitted in the country where it is used; -- make sure that the Radio Remote Control works correctly, in compliance with the applicable standards in the relevant country; -- not modify the Radio Remote Control conformity, by performing modifications or technical operations that change its operation.
Conformity 13 Unit FCC ID IC number FJL Transmitting Unit Model FJL Type NF022 OQA-FJLNF022 9061A-FJLNF022 FJM Transmitting Unit Model FJM Type NF022 OQA-FJMNF022 9061A-FJMNF022 FJM Transmitting Unit Model FJM Type NZ422 OQA-FJMNZ422 9061A-FJMNZ422 FJN Transmitting Unit Model J2F Type NZ322 OQA-J2FNZ322 9061A-J2FNZ322 FJQ Transmitting Unit Model J2F Type NZ322 OQA-J2FNZ322 9061A-J2FNZ322 FJR Transmitting Unit Model FJR Type NF022 OQA-FJRNF022 9061A-FJRNF022 FJR Transmitting Unit Model
Conformity Read carefully the section of the Manual where the antenna position is described, both in the general part and in the specific part referring to the Receiving Unit. 3.1.1 Federal Communications Commission (FCC) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Frequencies 4 15 Frequencies Dynamic series' Radio Remote Controls can work in the 915-928MHz frequency band. The Radio Remote Controls' working frequency is defined by market-specific laws and standards. In order for the system “Machine+Radio Remote Control” to be compliant and therefore to be used, these laws and standards must be respected: if they are not, the Radio Remote Control cannot and must not be used.
Via Pomaroli, 65 - 36030 Caldogno (VI), ITALY PH: +39 0444 901000 - Fax: +39 0444 901011 info@autecsafety.com - www.autecsafety.
