LIURPD002_eng-00 Instruction Manual for the use and the maintenance of the Radio Remote Control Original instructions Part D: HACRP8 (Model RPD) Receiving Unit AIR SERIES
THIS PART OF THE MANUAL CONSISTS OF Part D - Information, instructions and warnings for the HACRP8 (Model RPD) Receiving Unit. The Manual consists of Part A – General, Part B – Conformity and Frequencies, Part C – Transmitting Unit, Part D – Receiving Unit, Part E – Battery and Battery Charger, plus the Technical Data Sheet.
It is also the responsibility of the Manufacturer and of the design professionals of the Machine on which the Autec Radio Remote Control is to be installed and used to be certain that the structure, condition, organization and markings of the Machine as installed at the facility is appropriate for and will allow for the safe and reliable use and control of the Machine through the Autec Radio Remote Control interface.
IT IS THE RESPONSIBILITY OF THE OWNER AND FACILITY OPERATOR, AND THEIR OFFICERS, MANAGERS AND SUPERVISORS, to be certain that all Users of the Autec Radio Remote Control and that all Persons who are or will be working with or near the Machine operated by or through the Autec Radio Remote Control are fully and properly educated and trained by qualified Personnel in the proper and safe use of the Autec Radio Remote Control and of the Machine, including without limitation complete familiarity with and understa
INDEX 1 Information on the use of instructions ...................................................................... 7 1.1 Structure of the Instruction Manual ....................................................................... 7 1.2 Caption and terminology ...................................................................................... 9 1.3 Symbols .............................................................................................................. 9 1.
7 1 Information on the use of instructions Before reading this part of the Manual, you must read and understand the general part (Part A) of the Manual provided with the Radio Remote Control. 1.
Usage and maintenance instructions are supplemented by the Radio Remote Control's Technical Data Sheet, that: - Describes the Transmitting Unit's configuration - Indicates the relation between commands sent by the Transmitting Unit and those available on the Receiving Unit. Usage and maintenance instruction as a whole are to be considered as an integral part both of the Autec Radio Remote Control and of the Machine, system, device or Machinery system where the Radio Remote Control is installed.
1.2 9 Caption and terminology Contact Autec if any of the instructions, symbols, warnings or images are not clear and understandable, or if you have doubts or questions.
1.4 To whom the instructions are addressed Addressees of instructions are listed in the paragraph with the same title in the general part: please refer to that part. 1.5 Instruction storage Regulation for the storage of instructions are described in the paragraph with the same title in the general part: please refer to that part. 1.
11 2 Brief product presentation 2.1 Series, Radio Remote Control and Unit The object of this part of the Manual is the HACRP8 (Model RPD) Receiving Unit of an Autec Air series' Radio Remote Control. Autec Air series' Radio Remote Controls are designed to be used on Machines and provide a command interface to their command and control system, to be used from an appropriate distance and position. 2.
3 Description of the Receiving Unit D E F SERIAL N. XXXXXX MANIF. DATE XXXX POWER SUPPLY RADIO MODULE FREQUENCY FREQUENCY 45-400V ±10%(0.3A)50-60Hz AIRRT32NM 433.050-434.790MHz 915-928MHz N12335 - Before switching on please read the user manual. - Adhere to safety rules. - Disconnect power source and wait 10 seconds before opening. - Prima dell'accensione leggere il manuale d’uso. - Attenersi alle norme di sicurezza. - Togliere l’alimentazione e attendere 10 secondi in caso di apertura.
13 4 Technical data Power supply of the HACRP8 Unit (Type FA00M) 45-400V (0.3A) Power supply of the HACRP8-A Unit (Type FAA0M) 45-400V (0.3A) Power supply of the HACRP8-B Unit (Type FAB0M) 24-48V Power supply protection fuse 2A 500V (5x20mm T) Antenna integrated STOP contacts rated current 4A (250V STOP contacts protection fuses 4A 250V (5x20mm T) Commands rated current 4A (250V Housing material PA6 (20% fg) Protection degree IP65 (NEMA 4) Weight 0.65kg (1.43lb) (0.
5 Technical Data Sheet The Radio Remote Control 's Technical Data Sheet: - Describes the Transmitting Unit's configuration - Indicates the relation between commands sent by the Transmitting Unit and those available on the Receiving Unit. The Technical Data Sheet must be filled in, checked and signed by the Installer, who is responsible for correct wiring.
15 8 Operation 8.1 Radio module The radio module contains the address key, where also the Radio Remote Control configuration data are stored. The Receiving Unit cannot work without this address key. 8.2 DIP switches DIP switch 1 is used to set the frequency band. DIP switch 2 shall always be set in the OFF position. The normal position of DIP switch 2 is OFF. This position must not be modified. 8.
9 Installing the Receiving Unit The chapter "Installation" in "Part A" of the Instruction Manual contains the warnings for the installation that add to those provided in this chapter. Therefore, please refer to that part of the Manual. 9.1 Warnings for the Installer The Installer must: - Observe and comply with all instructions and warnings provided by the Machine Manufacturer.
17 9.2 Mounting and fastening the Receiving Unit in the best position The Receiving Unit, if equipped with a plug, may be directly connected to the electrical panel of the Machine by fastening it through the locking levers on the plug. It is recommended that adequate protection (e.g. a metal wire between the Receiving Unit and the Machine) is arranged to prevent it from falling should a release occur.
9.3 Positioning the antenna The Receiving Unit is not set up for the use of an antenna extension kit. 9.4 Wiring The metal housing of the plug connecting the Receiving Unit to the Machine's electrical panel must be wired to the earth connector so as to avoid hazards relating to electrical safety. Voltage in the outputs of the Receiving Unit shall not exceed 250V .
19 10 Maintenance Instructions for correct Radio Remote Control maintenance are described in the chapter "Maintenance" included in "Part A" of the Instruction Manual. Therefore, please refer to that part of the Manual. 11 Malfunction signalled by the Receiving Unit The table below lists malfunctions that are signalled by LEDs on the Receiving Unit and the solution to those malfunctions.
Via Pomaroli, 65 - 36030 Caldogno (VI) - Italy Tel. +39 0444 901000 - Fax +39 0444 901011 info@autecsafety.com - www.autecsafety.
