Install guide

ARMY TM 5-6675-308-34
MARINE CORPS TM 08837A-34/2
a. Removal. Remove rivets securing part by drilling
or other suitable means; remove part.
b. Replacement.
(1) Secure part in position with rivets.
(2) Swage rivets in place.
3-22. PADS Transit Case Maintenance. Maintenance of
the PADS transit case consists of replacing the shock
and vibration isolator mounts (8, figure 3-14).
a. Removal.
(1) Release latches and remove cover (l).
NOTE
Pin housing (5) must be removed to re-
place two of the shock and vibration
isolator mounts.
(2) Remove two screws (2), lockwashers (3), and
washers (4) securing pin housing (5) to pallet
mounting base (12); remove pin housing.
(3) Place a block under the pallet mounting plate
(12) to prevent it from tiltin when a shock
and vibration isolator mount (8) is removed.
(4) Remove four bolts (6), washers (7), screws (9),
washers (11), and lockwashers (10) securing
shock and vibration isolator mount (8) to pal-
let mounting base (12); remove mount.
b. Replacement.
(1) Secure shock and vibration isolator mount (8)
to pallet mountin
base (12) with four screws
(9), lockwashers (10), washers (11), bolts (6),
and washers (7).
(2) Remove block from under pallet mounting
plate (12).
(3) Secure pin housing (5) to pallet mountin base
(12) with two screws (2), lockwashers (3), and
washers (4).
(4) Replace cover (1) and secure with latches.
3-23. IMU Transit Case Maintenance. Maintenance of
the IMU transit case consists of replacing the shock and
vibration isolator mounts (5, figure 3-15).
a. Removal.
(1)
(2)
(3)
3-44
Release latches and remove cover (1).
Place a block under the mounting chassis (10)
to prevent it from tiltin when a shock and
vibration isolator mount (5) is removed.
Remove 8 screws (2 and 7) and 16 washers (3,
4, 8, and 9) securing shock and vibration isola-
tor mount (5) to base (6) and mounting chassis
(10); remove mount.
b. Replacement.
(1) Secure shock and vibration isolator mount (5)
to base (6) and mounting chassis (10) with 8
screws (2 and 7) and 16 ‘washers (3, 4, 8, and
9).
(2) Remove block from under mounting chassis
(3) Replace cover (1) and secure with latches.
3-24. Winterization Kit. Installation of the winteriza-
tion kit consists of removing heater air intake system,
removing rear panel, installing side and bottom mount-
ing plates on rear panel, installing angle bracket on rear
panel, installing nut plates on vehicle body, cutting out
rear panel to install door and frame, installing door
frame, installing porro prism door on rear panel, install-
ing transition joint and flexible heater hose, installing
the CDU winter mounting bracket, and installing rear
panel in vehicle.
a. Remove Heater Air Intake System.
(1) Remove four sheet metal screws securing air
intake pipe to heater flange and air intake
duct. (See figure 3-16, sheet 1).
(2) Remove four bolts, washers, and nuts securing
air intake duct to rear panel.
.
(3) Remove air intake pipe and duct. Return them
to the supply system.
(4) Reinstall the four bolts, washers, and nuts
removed in step (2) above in the holes in the
rear panel.
b. Remove Rear Panel.
(1) Remove spare tire and fuel can from utility
truck.
(2) Remove 18 bolts, washers, and nuts securing
rear panel to utility truck
panel and place protective
equipment.
body; remove rear
cloths on electrical
Exercise care to prevent damage to gas-
ket cemented around periphery of panel.
(3) Clean any caulking compound from edges of
rear panel and utility truck body.
c. Install (Left and Right) Side Mounting Plates,
880524-1 and -2, Plate 880526-1, and Handles
on Rear Panel.
(1) Place side mounting plate 880524-1 (7, figure
3-16, sheet 2) on right side of outer surface of
rear panel. Locate side mounting plate so that