INSTALLATION AND OPERATION MANUAL INTEGRATOR RACKS
IMPORTANT SAFETY INFORMATION PRÉCAUTIONS DURANT UTILISATION 1. Read these instructions. 1. LISEZ ces instructions. 2. Keep these instructions. 2. Tenez ces instructions. 3. Heed all warnings. 3. Notez tous les avertissements. 4. Follow all instructions. 4. Suivez toutes les avertissements. 5. Do not use this apparatus near water. 5. N’utilisez pas ce produit près de l’eau (la piscine, la plage, le lac, etc.). 6. Clean only with dry cloth. 6. Nettoyez seulement avec une étoffe sèche.
INTRODUCTION AND CONTENTS INTEGRATOR RACKS INTRODUCTION 3 The Australian Monitor Integrator range of equipment racks are a sturdy and professional rack mounting solution. UNPACKING 4 Available in wall mount versions of 6 and 12 rack unit heights and with three floor mount variants in 18, 32 and 45 rack units, the Integrator range of racks give the AV contractor the features they require in a reliable cost effective racking solution.
UNPACKING 1 Unpacking the Boxes The rack will be packed into three separate boxes. The boxes contain the following: Top and Bottom Piece and Accessories Front Door and Side Panel Rear Door and Side Panel Please ensure that all three boxes have turned up with your delivery, if a box is missing please contact your local distributor.
PREPARING THE TOP PIECE 2 Mounting the lock catches The lock catches mount to the underside of the top piece. The mount with the flat side facing the outside of the rack as per the diagram. With the accesories there is a small bag of screws that contains 4 x M5x10 self tapping screws and 4 x M4x8 self tapping screws. The 4 x M5x10 screws are used to mount the lock catches.
PREPARING THE BOTTOM PIECE 4 Removing the corner covers The bottom piece will need the corner covers removed just like the top piece. This will allow you access to mounting the frame’s side pieces to the top and bottom. 5 Installing the Wheels/Stand offs The wheels or stand offs mount to the bottom of the bottom piece. The stand offs simply screw into the bottom piece. The wheels on the other hand will need to be screwed into the based with the 16 x M6x10 silver self tapping screws.
PREPARING THE DOOR/LOCKS 6 Mounting the front/rear locks The locks and key sets will now need to be mounted to the front and rear door. NOTE: It is easiest to lay the door on a flat surface with pressure on the lock when doing this and step 6 and 7. The lock has two screws in the centre of the lock that hold on a bracket. These screws will need to be removed so the bracket can go on the backside of the door and the lock can go on the front side.
PREPARING THE SIDE PANEL 10 Mounting the front/rear lock catches The front and rear lock catches mount on the side panels and allow the front and rear door to be locked. You will need to use the 4 x M4x8 screws to mount the lock catches, they mount with the catch facing inside the rack. NOTE: It is suggested that one screw be installed halfway followed by the second screw as to stop the small metal piece from spinning on one screw causing damage to the rack and installer.
MAKING THE FRAME 11 Mounting the top to the side panels With the fan tray and corners removed from the top piece you can use the 8 x M8x25 hex bolts supplied in the accessories to mount the top to the side frames. It is easiest to remove the inner panel from the side frames for this step as shown. Ensure the side panels are up the right way when mounting to the top and bottom piece. The RU markings on the side panel should start with “01” at the bottom.
MOUNTING THE DOORS 13 Mounting the Doors In order to mount the doors to the frame you will need to located the smaller size studs from the accessories. These simply slide in the provided holes in the bottom piece. The door has a spring loaded catch that holds the top of the door to the top piece, whilst pulling the spring loaded catch back the bottom of the door should sit on the stud then the top of the door can be moved into place. Make sure the door freely swings fully open.
SPECIFICATIONS FLOOR STANDING RACKS INT18 INT32 INT45 600 x 800 x 1050 23.6” x 31.5” x 41.3” 600 x 800 x 1620 23.6” x 31.5” x 63.7” 600 x 800 x 2200 23.6” x 31.5” x 86.6” Net Weight 57.0 Kg 125.4 lb 82.0 Kg 180.4 lb 102.0 Kg 224.4 lb Shipping Weight 60.3 Kg 132.7 lb 85.3 Kg 187.7 lb 106.3 Kg 234 lb Total Weight Rating (Including Rack) 600 Kg 1320 lb 800 Kg 1760 lb 800 Kg 1760 lb Dimensions in mm (W x D x H) (On Wheels) WALL MOUNT RACKS INT6 INT12 600 x 545 x 370 23.
ENGINEERED BY AUSTRALIAN MONITOR Address: 1 Clyde Street, Silverwater, Sydney NSW 2128 Australia. Private Bag 149, Silverwater NSW 1811 ABN 78 001 345 482 Website: www.australianmonitor.com.au International enquiries email: international@australianmonitor.com.au DISTRIBUTED IN AUSTRALIA AND NEW ZEALAND BY HILLS SVL www.hillssvl.com.au NSW P: 02 9647 1411 E: nsw@hillssvl.com.au QLD P: 07 3852 1312 E: qld@hillssvl.com.au ACT P: 02 6260 4544 E: act@hillssvl.com.au WA P: 08 9204 0200 E: wa@hillssvl.com.
