AMIS SERIES 6 0 W / 1 2 0 W M I X E R A M P LIFIER I N S TA L L AT I O N A N D O P E R AT I O N M ANUAL AMIS SERIES 60/120 manual.
I M P O RTANT SAFETY INFORMATION 1. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original factory packing. 2. Read all documentation before operating your equipment. Retain all documentation for future reference. 3. Follow all instructions printed on unit chassis for proper operation. 4. Do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 5.
INTRODUCTION AND CONTENTS The AMIS60 and AMIS120 mixer amplifiers are designed for commercial installations. Both models operate on 230/240 VAC, 50Hz (115VAC, 60Hz) or 24 VDC, and may be desk or rack mounted (rack mount kit supplied fitted). The AMIS60 will deliver 60 watts into a load of 8 ohms, 70 volt or 100 volt line. The AMIS120 will deliver 120 watts into a load of 4 or 8 ohms, 70 volt or 100 volt line. Both Models feature 6 universal mic/line inputs.
F R O N T PA N E L 1 1 2 3 4 5 6 CH 1-6 These control the individual level for each channel input. 2 BASS There is 12dB of cut and boost at 100Hz. This EQ is the shelving type. 3 TREBLE There is 9dB of cut and boost at 10kHz. This EQ is the shelving type. 4 MASTER This controls the overall output level. 5 ON This LED indicates the unit is powered “on”.
R E A R PA N E L 11 4 7 10 1 12 3 2 REC OUTPUT The REC output is on unbalanced RCA connectors. The output level is 300mV into 10kohm at rated output. The output is dual mono. The REC output is not affected by the MASTER volume control or the BASS and TREBLE controls. The REC output does not receive the tone signal. 3 LINE OUTPUT The LINE output is on a balanced XLR connector. The output level is 2V into 1k at rated output.
I N S TA L L AT I O N MOUNTING OUTPUT CONNECTIONS When rack mounting, it is advisable to allow 1 rack space above and below the amplifier. When multiple amplifiers are mounted in a rack, exhaust fans should be used on the rack. Airflow for cooling the amplifier is by convection from bottom to top and by fan left to right. The output terminal strip accepts wire sizes from 16-22AWG (1.5mm2 - 0.35mm2). The following table should be used as a guideline for cable sizes.
SETUP & TROUBLESHOOTING Levels Volume controls should aimed to be set at nominal, which is at the half or 12o’clock position. Any unused channels should be set to minimum. When establishing a mix, remember: Less is more.
DIMENSIONS PA G E 8 AMIS SERIES 60/120 manual.
BLOCK DIAGRAM A M I S S E R I E S I N S TA L L AT I O N & O P E R AT I O N M A N U A L AMIS SERIES 60/120 manual.
S P E C I F I C AT I O N S POWER OUTPUT (0.5%THD, 1KHZ) S/N RATIO POWER BANDWIDTH (-3DB +1DB) OUTPUT REGULATION SIZE (WXHXD) NET WEIGHT SHIPPING DIMENSIONS (WXHXD) SHIPPING WEIGHT AMIS 60 AMIS 120 60W 120W > 76dBr > 76dBr 60Hz-15kHz 60Hz-15kHz 90% 90% 482x88x313.5mm 19”x3.5”x12.3” 482x88x313.5mm 19”x3.5”x12.3” 8.5kg 18.7lb 11.0kg 24.2lb 525x175x385mm 20.7”x6.9”x15.2” 525x175x385mm 20.7”x6.9”x15.2” 10.5kg 23.1lb 13.0kg 28.6lb COMMON TO ALL MODELS THD (1KHz, -1dB) < 0.
S P E C I F I C AT I O N S AMIS 60 AMIS 120 MAINS CURRENT DRAW (240V) FULL POWER 1/3 POWER 1/8 POWER IDLE 0.75A 0.50A 0.40A 0.25A 1.5A 0.95A 0.65A 0.15A MAINS CURRENT DRAW (115V) FULL POWER 1/3 POWER 1/8 POWER IDLE 1.6A 1.0A 0.80A 0.50A 3.1A 2.0A 1.4A 0.
AUSTRALIA AND NEW ZEALAND w w w. a u s t r a l i a n m o n i t o r. c o m . a u SYDNEY MELBOURNE BRISBANE ADELAIDE PERTH AUCKLAND (NSW & ACT SALES) (VIC & TAS SALES) (QLD SALES) (SA & NT SALES) (WA SALES) (NZ SALES) 1 Clyde Street Silverwater NSW 2128 Private Bag 149 Silverwater NSW 1811 Phone: (02) 9647 1411 Fax: (02) 9648 3698 Email: nsw@audiotelex.com.
