Tourer Black Installation Manual

ManualsBrandsAussie Traveller ManualsCaravan Awnings & AnnexesTourer Black Fade Roll-Out Awning

1300 663 868 | enquiries@aussietraveller.com.au | aussietraveller.com.au

BRISBANE SHOWROOM: 11-15 Oasis Court, Clontarf QLD 4019 | MELBOURNE SHOWROOM: 235 Barry Road, Campbellﬁeld VIC 3061

1. Erect awning as per manufacturers’

instructions. Ensure the frameset/roller is set

at the predetermined height to suit the wall

measurements.

2. Ensure the roller pull strap sail track is positioned at

approximately 9 o’clock (left end) or 3 o’clock (right

end). This will allow rain water to run off the fabric.

Refer to Diagram 1.

3. We recommend that the awning frameset leg

remains attached to the bottom of the van.

If you choose to disengage the legs and relocate

them into the patio position, please ensure the

awning user instructions are followed as the wrong

procedures could cause damage to occur to the

ratchet mechanism of the roller.

If the legs are disengaged, ropes, straps and pegs

should be used to ﬁrmly ﬁx the awning to the

ground.

4. Unpack the AFK from carton. Find the 2 sections

which ﬁt to the wall brackets on the caravan. These

2 sections have the joiner piece ﬁtted inside for

transport/packing purposes.

Remove the 2 set screws, slide the joiner piece out,

reverse the direction and reﬁx in place using the

original set screws. Refer to Diagram 2.

5. Release the locking cam handles and ensure the top

clamp section of the AFK is in the open position.

Slide the two sections of the AFK together.

Refer to Diagram 3.

6. Fit the pole end into the wall bracket, ﬁxed to side

of van. Ensure the top clamp section of the AFK

is in the open position, lift up the AFK until it rests

under the awning fabric. Extend the AFK out until

the spigot ﬁts into the hole in the roller. Ensure the

AFK is fully extended and tighten the knurl knob.

Refer to Diagram 4, 4A and 4B on following page.

ANTI FLAP KIT AND WALLS FOR ROLL OUT AWNINGS

Roof fabric

Level ground line.

Pull strap sail track at 9

o’clock position (left

end).

Predetermined

front wall height.

Diagram 1

Diagram 2

Original packed

position

Reverse direction

& Re-ﬁx

Fixed into Position

Diagram 3

Top clamp section in

open position.

Locking cam

handle.

Slide 2 sections

together.

Summary of content (3 pages)

PAGE 1
ANTI FLAP KIT AND WALLS FOR ROLL OUT AWNINGS 1. Erect awning as per manufacturers’ instructions. Ensure the frameset/roller is set at the predetermined height to suit the wall measurements. Diagram 1 Roof fabric Pull strap sail track at 9 o’clock position (left end). 2. Ensure the roller pull strap sail track is positioned at approximately 9 o’clock (left end) or 3 o’clock (right end). This will allow rain water to run off the fabric. Refer to Diagram 1. Predetermined front wall height. 3.
PAGE 2
Diagram 4 - Fit pole end into wall bracket Fit pole end into wall bracket on side of van. 6. Hold the fabric in position on top of the AFK at the gap in middle of the two sections with one hand and tighten the locking cam handles with the other hand. Ensure the fabric is fully secured at the gap between the two sections of the AFK. Refer to Diagram 4B. 7. The outside edges of the fabric should now be securely clamped with minimal deflection in the line of the fabric i.
PAGE 3
HELPFUL HINTS If you intend to set up the awning and walls at the same time: 1. When erecting the awning over extend the roller so the pull strap sail track is positioned at the 6 o’clock position (at the bottom) before attempting to fit the AFK’s. 2. Slide the long side wall into pull strap sail track of the roller and then rotate the roller back to the 9 o’clock (left end) or 3 o’clock (right end) position. (Refer to awning user/operating instructions). 3.