Effective January 2009 INSTALLATION & OPERATING INSTRUCTIONS Serial Number: B.D. Number: Model: IS700/IS007 PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE Aurora CLIMATE SYSTEMS A.B.N. 43 108 083 987 SAI Global Approval No.
TABLE OF CONTENTS SAFETY LABEL OPERATING INSTRUCTIONS To The New Owner Safety Labels 2 Automatic Humidifier Operation 28 3-4 Operating Instructions Checklist 29-30 INSTALLATION INSTRUCTIONS Specifications 5 General Safety Information 6 Clearances to Combustibles 7 Log Installation Fluing Requirements 8-9-10-11 12 Fluing Options / Installation 13-20 Optional Remote Control Thermostat 21-22 Lighting Instructions 31 Fan Operation 32 Shutdown Instructions 32 High Temperature Cut Out
TO THE NEW OWNER Congratulations! You are the owner of a state of the art Archer High Efficiency Gas Log Space Heater. This appliance has been designed to provide you with all the warmth and charm of a wood fire at the flick of a switch. The Archer Gas Log Space Heater promises to provide you with the highest economy, heat output, comfort and security.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE ! IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE INJURY OR PROPERTY DAMAGE. REFER TO THIS MANUAL FOR ASSISTANCE OR ADDITIONAL INFORMATION, CONTACT AURORA CLMATE SYSTEMS. TELEPHONE NUMBER (03) 9795 8895 THIS APPLIANCE MUST BE INSTALLED OR SERVICED ONLY BY A LICENCED GAS FITTER FOR THE INSTALLATION AND/OR SERVICE OF THE ARCHER GAS LOG SPACE HEATER.
SAFETY LABELS Model - Archer Ο Ο Gas Type Model Type Natural IS700 Ο LPG IS700 Ο Gas Consumption Manifold Pressure Injector Size - Front - Rear SAI Global Approval No to Code AS4553 31MjHr 0.7Kpa 2.15mm 2.15mm 28MjHr 1.4Kpa 1.3mm 1.3mm 240V 50 Hz Aurora Climate Systems A.B.N. 43 108 083 987 71 - 73 Overseas Drive Noble Park VIC 3174 To be installed by an authorised person in accordance with installation instructions GSCS20025 provided with appliance.
SPECIFICATIONS - MODEL NO.
INSTALLATION INSTRUCTIONS GENERAL SAFETY INFORMATION 1. This installation must conform with local codes or, in the absence of local codes, with AG 601. 2. Provide adequate clearances around the product for servicing and ensure there are no obstructions to the combustion air intake situated at the back of the heater. (Refer Page 5 item 10 and page 7) 3. The appliance must be installed on a flat, solid continuous surface (ie. wood, metal, concrete).
INSTALLATION INSTRUCTIONS CLEARANCE TO COMBUSTIBLES Insert Model IS700 A B C B C D A Zero clearance No hearth required Note: A Rear Wall to Unit 25mm B Side Wall to Unit 15mm C Corner Installation 0mm D Height Clearance From Unit 15mm The Archer Gas Log Space Heater has been tested and approved for zero clearance to combustible materials. Aurora Climate Systems recommends that clearances as listed above should be maintained to allow for removal of the product for servicing.
INSTALLATION INSTRUCTIONS (Side view main logs and burners) 1. Rear Log 2. Middle Log 3. Front Log 4. Rear Burner 5. Front Burner 1 3 NOTE: 5 2 4 Do not change position of front, middle and rear logs as their positions have been present at the factory. Changing log positions will result in faulty gas burner function or sooting up.
INSTALLATION INSTRUCTIONS LOG INSTALLATION - MODEL IS 700 The gas log set (front log, middle log, rear log, left hand side log and right hand side) is pre-set and installed in the factory. Only the left and right hand cross logs are packaged separately inside the firebox for installation by the installer. 1. To access the right and left hand cross logs: Remove bottom grill. See illustration below.
INSTALLATION INSTRUCTIONS 3. Remove all cardboard protection from inside the firebox and the two cross logs. Note: All other logs in the firebox have been preset in the factory and their location should not be changed. Check that logs have not been damaged in transit and the rear log is hard up against the rear of the firebox at the base and at the top. 4. Carefully remove wrapping from right and left hand cross log. WARNING 5.
INSTALLATION INSTRUCTIONS LOG SET DIAGRAM - IS700 The Gas Log Kit contains the following: 1) 2) 3) 4) 5) 6) 7) 1 Rear Log Middle Log Front Log L/H Side Log L/H Cross Log R/H Side Log R/H Cross Log 2 7 5 6 4 3 INSTALLERS - PLEASE NOTE (A) LOG SETTINGS Do not remove logs from heater unless absolutely necessary!! Logs have been preset and aligned for correct performance. Only place cross logs in position as per instructions above.
INSTALLATION INSTRUCTIONS FLUING REQUIREMENTS Co-Axial Flue Installations Note: This appliance has only been approved for co-axial flue application if the flue (as supplied by the manufacturer) is installed to an external wall or external fireplace.
SINGLE FLUE KIT FOR ARCHER GAS LOG SPACE HEATER For applications on Flexible Single Flue refer pages 16-17-18-19-20 No Description Qty 1 Single Flue Adaptor 1 Supplied with heater 2 40mm ø PVC Pipe 400mm long 1 Supplied with heater 3 90° PVC Bend 1 Supplied with heater 4 40mm ø PVC Pipe (up to 5.
CO-AXIAL FLUE KIT FOR ARCHER GAS LOG SPACE HEATER For applications refer page 15 and page 16 of this Installation Manual. No Description Qty 1 Co-Axial Manifold Starter 1 2 Internal Pipe Spacers 2 3 40mm ø PVC Pipe 400mm 4 65mm ø PVC Pipe 400mm 5 Stainless Steel Co-Axial Cowl 1 6 Air Inlet Duct Cover 1 Approx. 6 2 3 5 2 Mounting Plate 1 4 15mm Use 4 self tapping screws provided with assembly 4mm ø x 15mm long.
INSTALLATION INSTRUCTIONS Insert Model IS700 -With Co-Axial Flue - Exterior Masonary Fireplace Co axial Flue Pipe up to 1 metre long 1/2” BSP Gas Connection Note: Do not use PVC cement to seal flue pipe connections to allow for removal of flue pipe. Incorporate loop in gas connection or use flexible hose for gas connection to allow for removing of appliance from fireplace.
CREATED FIREPLACE MODEL IS100/IS200 Zero clearance, power flue, single 40mm flue and shallow unit depth allow you to create your own fireplace anywhere in your home with your choice of mantel. Note: Heater must be able to be removed easily for servicing. (Not locked in) 1 2 500mm 6 5 5100mm Maximum 4 4 9 7 8 1 2 3 97mm 97mm 3 INTERNAL WALL APPLICATION EXTERNAL WALL APPLICATION 1. 2. 3. 4. 5. 6. 7. 8. 9. 1. 2. 3. 4.
INSTALLATION INSTRUCTIONS Internal to External Wall Installation using 40mm ø PVC Flue. Side Wall Installation (Horizontal Single Flue) External Wall Internal Wall 90º Elbow Concrete Slab CAUTION: 40mm PVC Pipe PLEASE DO NOT ALLOW WATER TRAPS TO FORM IN FLUE OR HEATER WILL CEASE TO OPERATE. Note: Total installation length in 40mm ø PVC pipe 5100mm with 1 x 90º and 2 x 45º bends. 17 75mm stainless steel cowl to suit 40mm PVC flue pipe.
INSTALLATION INSTRUCTIONS Internal Wall Under Floor Installation using 40mm ø PVC Flue. Internal Wall External Wall 90º Elbow 75mm stainless steel cowl to suit 40mm PVC flue pipe. 90º Elbow Note: All flue pipe connections need to be sealed with PVC cement, except Flue Fan Connection. Note: Total installation length in 40mm ø PVC pipe 5100mm with 1 x 90º and 2 x 45º bends.
INSTALLATION INSTRUCTIONS Flexible Flue Kit to suit Fireplace Insert Installations Model IS700 STANDARD FLUE KIT SUPPLIED BY AURORA FOR INSERT INSTALLATION (SFA002) Note: Standard 75mm Cowl to fit 40mm ø pipe is also supplied with flue kit. 40mm N.B. Plain Coupling (Supplied with Flue Kit) (38mm I.D.) 50mm Nylaflow Flexible Hose Nylaflow G.P. Hose Code AH50WAS (Supplied with Flue Kit SFA002) 40mm N.B. SWV Pipe (Not Supplied) 60mm S.S. Hose Clamp Note: I.D.
INSTALLATION INSTRUCTIONS Fireplace Insert Installation Model IS100 -Using Aurora Flexible Flue Kit SFA002 with Single 40mm PVC Flue Pipe using 75mm cowl Fasten 40mm Flue Pipe with bracket to stop flue pipe being forced downwards ( Supplied by Installer) Gas Cowl Supplied in flue kit 200mm Galv Sheet Flashing to seal chimney (Supplied by Installer) 40mm PVC Pipe SWV (Supplied by Installer) 2 x 45º PVC bends 40mm (Supplied by Installer if required) 5100mm MAX Aurora flexible flue kit SFA002 Use 1/2”
OPTIONAL REMOTE CONTROL THERMOSTAT An optional programmable Remote Control Thermostat can be fitted to the heater at the factory when ordered or even after the heater has been installed. See your Archer dealer for correct type. Installation:The Remote Control can be installed by the owner of the heater if required. The Remote Control is a battery operated device, which requires a small amount of low voltage plug in wiring.
ARCHER GAS LOG SPACE HEATER INSTALLATION OF THE REMOTE RECEIVER AND FRONT FLAME DISPLAY BUTTON Effective 15th April 2008 VIOLET Caution: Please make sure heater is unplugged when installing Remote Control RED BUTTON Please Note: The front panel must be opened for this wiring to occur. The front panel simply pulls forward - no tools required. Caution: When removing front panel as there are low voltage wires attached to the inside of the front panel.
INSTALLATION INSTRUCTIONS GAS CONNECTION (Line Supply) The gas connection is 1/2” BSP supplied in heater. GAS SUPPLY LINE TO HEATER a) b) c) d) Remove the 2 screws on top L/H front side panel and lift out side panel. Remove rubber grommet from back panel of heater and insert 1/2” copper gas supply line through back panel of heater. Connect gas supply line to flexible gas hose. Ensure that flexible gas hose is not kinked after fitting gas supply line.
INSTALLATION INSTRUCTIONS GAS VALVE PRESSURE ADJUSTMENT The gas valve pressure adjustments must be checked during installation, and if necessary corrected to suit the gas type available. (Reference Page 11) “A” represents the main regulator adjusting screw. Access to this screw is obtained by removing the brass screw cover; use a flat blade screw driver for adjustment of gas pressure.
ARCHER 2004 WIRING DIAGRAM 240V 50 Hz TRANSFORMER 240V 240 V ACTIVE BROWN EARTH GREEN CONVECTION FAN (2) TR.PRIMARY BLACK TR.PRIMARY WHITE (8) 240 V NEUTRAL BLUE J1 NEUTRAL ( 7-5-3 ) PIN 18 HSI HSI PIN 16 0.47 uF PIN 6 1 uF PIN 4 F OVER TEMP .80 C R FRONT AND REAR GAS VALVES M 25 1 0 FRONT BURNER SWITCH PIN 5 14 WAY RIBBON TO DISPLAY PIN 20 CONV.FAN.BLACK ( 13 ) (1) CONV.FAN.BLUE MAIN GAS VALVE E 8 REAR.H.S.I. (19) (20) GAS.VALVES.ACTIVE FRONT.H.S.I. (17) (18) REAR.H.S.I. LOW.
INSTALLATION INSTRUCTIONS MAIN DOOR SAFETY SCREEN INSTALLATION ! CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SURFACE TEMPERATURE FROM THE MAIN DOOR GLASS AND SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING IGNITION. YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISED WHEN THEY ARE IN THE SAME ROOM AS THE APPLIANCE.ALWAYS ENSURE THAT YOUR SAFETY SCREEN SUPPLIED WITH THE HEATER IS FITTED TO THE MAIN FRONT DOOR OF THE HEATER. Slide tabs between glass and door frame in an upward motion.
ASSEMBLY AND FITTING OF 3 AND 4 SIDED SURROUND FOR FLAT FRONT MODEL IS 700 DIAGRAM A (A) Fastening Points IMPORTANT NOTE: When fitting the surround to the heater the main door and the lower front panel must be removed. Please keep the wiring intact when removing the lower front panel. (1) (2) (C) DIAGRAM B (B) Fastening Points (D) 1. 2.
AUTOMATIC HUMIDIFIER OPERATION Most gas heaters dry out the air in the room. (Remember the bowls of water in front of the old gas heaters?) The Archer has ingeniously solved this problem with an Automatic Humidifier. Gas contains moisture which is normally expelled out the flue or chimney after combustion. But the Archer is so efficient by taking 92% of the heat out of the burnt gases that the moisture drops out and condenses in the back of the heater.
OPERATING INSTRUCTIONS CHECKLIST BEFORE OPERATING THIS APPLIANCE, CAREFULLY PROCEED THROUGH THE FOLLOWING CHECK LIST. 1. Read and understand these instructions before installing or operating this appliance. 2. Installation of this appliance is only to be carried out by a licensed gas fitter who preferably should be familiar with the installation of the Archer Heater. 3.
OPERATING INSTRUCTIONS CHECKLIST cont... 11. Prior to operating the appliance check for dust or particles lying on top of the burners. Refer Page 10. 12. Check and verify that logs are placed correctly as per instructions on Pages 8-11 of this Installation Manual. If logs are incorrectly positioned or placed wrongly it can create a hazardous situation, and in most instances, the heater will not operate correctly. 13. Do not light heater without logs fitted, as heater will not operate. 14.
LIGHTING INSTRUCTIONS 1. Main Electrical power supply must always be switched on to the unit with the two burner switches in the off position (up) before commencing lighting the heater. 2. Turn on main gas supply. 3. Verify that main electrical supply is switched on by checking the 240V AC power status display indication is on. 4. Burner selection: select low burn, medium burn, or high burn. Low burn switch (Item 1) controls the f r o n t burner only.
FAN OPERATION The 3-speed main convection fan will cut in automatically approximately 3 to 5 minutes after the heater has warmed up. Note: The 3-speed main convection fan is automatically controlled and will operate on three preset speeds. Depending on your burner setting and the surrounding ambient temperature, the L.E.D lights (Items 7, 8 and 9) for the fan will light up. The bottom L.E.D light (Item 7) is low speed setting, and middle L.E.
OVER TEMPERATURE CUT OUT The Archer Gas Log Space Heater is protected against overheating with a high temperature 80° cut out switch to protect the heat exchanger, plastic sump and flue fan. The high temperature cut out switch will automatically switch off the gas supply to the heater, if the temperature in the room where the heater is located reaches approximately 28°C. The heater will go into lock out mode.
UNIT OPERATING FAULTS SERVICE AND INSTALLATION OF THE APPLIANCE SHOULD BE CARRIED OUT BY AUTHORISED PERSONNEL ONLY. THE MAJOR CAUSE OF OPERATING PROBLEMS WITH GAS LOG SPACE HEATERS IS IMPROPER GAS PRESSURE, INCORRECT LOG PLACEMENT, IMPROPER INSTALLATION, INCORRECT FLUE INSTALLATION, INCORRECT SWITCHING OF BURNERS, DIPS/SPIKES IN THE INCOMING POWER OR REVERSE POLARITY’S.
MAINTENANCE Note: Your appliance should be inspected, serviced and checked annually by a qualified service person to ensure that your appliance is operating safe and efficiently. Should you detect any abnormality in the operation of your appliance call a qualified service person who has been trained and approved to inspect and service the appliance. This may be your installer or dealer.
GOLD PLATED/CHROME PLATED/STAINLESS STEEL DOORS The gold and chrome plated finish on the door requires little maintenance and needs only to be cleaned with a soft cloth and a small amount of Mr Sheen. Polish gently. Stainless Steel doors can be cleaned with a metal cleaner that can be used on Stainless Steel. Please note: Stains or imperfections on plated finishes are not covered under warranty.
COMPLETE UNIT WARRANTY DESCRIPTION WARRANTY PERIOD (FROM DATE OF PURCHASE) Heat Exchanger Main Convection Fan All Other Parts 5 Years Parts/1 Year Labour 2 Years Parts/1 Year Labour 1 Year Parts/1 Year Labour AURORA WARRANTY PROGRAM To qualify for the Aurora Warranty Program, you need to fill out the warranty registration form, and have your qualified installer fill out the Installation Commissioning Report. Both documents must be returned promptly to Aurora Climate Systems.
CONDITIONS, EXCLUSIONS AND QUALIFICATIONS cont... 6. Aurora further assumes no liability for defects or damage caused by incorrect operating or performance of the appliance caused by any modification or incorrect installation. Unauthorised components or installation modifications could create a fire hazard by altering the safety design of the Gas Log Space Heater. Flue Installation 7.
THIS WARRANTY DOES NOT APPLY TO THE FOLLOWING: 1. Breakage of glass components, door glass imperfections, (i.e. glazing, breakage or discolouring. 2. Corrosion, chips, scratches, blistering, fading, paint, metal finish imperfections or rusting due to the exposure of the appliance to man made or adverse natural atmospheric conditions or poor handling by the freight company, the installer or the customer. 3.
FREQUENTLY ASKED QUESTIONS 1. Front burner is lighting with the red button only. The rear burner isn't starting. (heaters fitted with remote control or wall thermostats) This usually means the remote or wall thermostat has not been switched to the “ON” position or the receiver box inside the heater behind the front panel needs to be re-learnt. This is done by removing the front panel and then locating the back receiver box as shown below. ADJ.
FREQUENTLY ASKED QUESTIONS cont’d 5. There is a hissing noise coming from the heater. Is this normal? This is a normal occurrence when the humidifier activates and will vary in timing and intensity. 6. There is condensate on the inside of the glass. Is this normal? Yes this is quite common especially from a cold start but will dissipate after a period of time. 7. The humidifier isn't working.
NOTES 42
ATTENTION APPLIANCE INSTALLER PLEASE RETURN THESE OPERATING & INSTALLATION INSTRUCTIONS TO THE CONSUMER (FOR FUTURE REFERENCE) DATE OF PURCHASE
