Shredder User Manual 1-800-327-8508 USA Only 1-310-793-5650 International Email: info@auroracorp.com AU608MB Model No. For more information, please visit us at: www.auroracorp.com Please read these operating instructions before using the unit.
WARNING: SAFETY INSTRUCTIONS, READ BEFORE USING! Read instructions before use. Do not spray or keep any aerosol products in or around the shredder. Avoid touching the document feed opening with hands. Keep loose clothing or jewelry away from the paper entry slot. Product is not intended for use by children (product is not a toy). Avoid getting hair near the paper entry slot. Do not insert foreign objects into the paper entry slot.
Paper Shredder Operating Instructions Installation Sheet Capacity Paper Shred Size Operation 6 Sheets of 20 lb. bond paper* 5/32 in. x 15/32 in. pieces 0.4 cm x 1.2 cm pieces Maintenance Paper Entry Width 8.7 in / 220 mm Troubleshooting Credit Card Capacity 1 at a time Duty Cycle 4 min. on / 30 min. off Voltage 120V AC 60Hz / 3.
OPERATION Control Switch Using the switch located on the unit, select one of the following settings by sliding the switch either left or right. (FIGURE 2) I FIGURE 2 Auto / On: This setting allows the shredder to be automatically started by inserting paper into the feed slot. Always feed the paper in as straight as possible. When the paper has passed through, the shredder will automatically stop. Off: This setting turns off all features of the shredder.
OPERATION Paper / Credit Card Entry: Make sure you do not exceed sheet count per pass (6 sheets max). Insert paper as straight as possible into feed slot and release. Insert one credit card at a time into the middle of the feed slot. NOTE: • Always turn off and unplug the shredder when not in use. • This shredder will shred staples and small paper clips. It is recommended that you remove paper clips whenever possible to extend the lifespan of your shredder.
MAINTENANCE Warning: Failure to properly maintain your shredder will void the warranty. Oil the shredder blades every month with basic vegetable, cooking oil or shredder oil. Follow oiling procedure below (FIGURE 3). It helps to keep the shredder blades operating well over many years of use. Oiling procedure: 1. Turn off shredder. 2. Apply shredder oil across paper entry. 3. Turn shredder in reverse mode for 3~5 seconds. Note: lubricating oil is NOT included.
TROUBLESHOOTING If there is a problem with your shredder, check below for the symptoms and steps to resolve. If you continue to have problems, contact customer support at our Service Center 1-800-327-8508. DO NOT ATTEMPT TO REPAIR BY OPENING THE SHREDDER HEAD. This will completely void the product warranty. The shredder does not work at all. 1) Make sure the unit is plugged in and that the outlet is in good working order.
TROUBLESHOOTING How to clear a paper jam in the shredder. 1) Switch the shredder over into Reverse (REV) mode. While in Reverse, the shredder will back up and loosen the jammed paper. If required, you may need to tug and remove several sheets to effectively clear the machine. When jammed paper is loosened or removed, switch back to the Auto-On mode to continue shredding. Repeat steps if needed.
SERVICE CENTER If you have any questions in regards to the operation of this shredder or in need of a spare part, please contact our service center at: Aurora Corp. of America Telephone: 1-800-327-8508 (U.S.A. only) or 1-310-793-5650 (International) Business hours: Monday to Friday 8:00 am - 5:00 pm PST (Pacific Standard Time) Email: info@auroracorp.com Or for more information, please visit our website at http://www.auroracorp.
1-800-327-8508 Usa Only / Los Estados Unidos Solomente • 1-310-793-5650 International / Internacional • Email: info@auroracorp.com • For more information, please visit us at: www.auroracorp.com 101819 © 2019 Aurora Corp.
