Installation & Assembly

ManualsBrandsAugust Grove ManualsFurnitureLarchwood 48'' Wide Kitchen Island

Table Of Contents



























































 









  

















































































ock-Down Constction, please fer to the last page

of instcons for steps to complete dwer assemb

















 















screwdriver

 











Summary of content (10 pages)

PAGE 1
IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the wood parts. We have taken great care in the design of this product and request that you carefully and strictly follow our assembly instructions to ensure a completed product as it was designed. Part List 0 E. Front Rail 1 pc.� .. C. Side Panel 1 pc. Side Panel 1 pc. F. Rail 1 pc. G Back 1 pc. D. Middle Panel 1 pc. Door 1 pc. . K.
PAGE 2
Assembly Instructions 2/9 IMPORTANT * Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future. * Do not tighten up all the screws until each part is properly assembled. * Use a soft cloth between these parts and the floor. STEP 1 Insert Cam Lock Screws into the pre-drilled holes of Side Panel (B) and (C), Front Rail (E) and (F), Back Rail (G) and (H), Bottom (J) and Back Piece (L).
PAGE 3
Assembly Instructions 3/9 STEP3 Slide Back Panel (K) into the groove of Back Rail (G) and (H) and Back Piece (L). Attach Middle Panel (D) to Front Rail (E) and (F), Back Rail (G) and (H) and Back Piece (L) using Cam Locks. (See figure 2) Figure 2 STEP4 Attach Side Panels (B) and (C) to unit using Cam Locks.
PAGE 4
Assembly Instructions 4/9 STEPS Attch Bottom (J) to unit using Cam Locks, Head Cap Bolts (long) and Washers. Tighten bolts using Hex Wrench. (See figure 3) Figure 3 STEP6 Head Cap Bolt (short) Attach Frame Leg (P) and (Q) to unit using Head Cap Bolts (short). Tighten bolts using Hex Wrench.
PAGE 5
PAGE 6
Assembly Instructions 6/9 STEP9 Pull out the Drawers from unit. Place Top (A) onto the unit, using Head Cam Bolts (long) and Washers. Tighten bolts using Hex Wrench. (see Figure 6) Side Drawers into place. 0 �+--Washer ©� _,Cap Bott (long) 90° Figure 6 STEP 11 To level the unit, adjust the adjustable levelers on the bottom. '' I '::;::, '::::::, I 'l I I I I I I I I STEP 10 When Leaf Top is down, it should be oriented vertically.
PAGE 7
Assembly Instructions 7/9 TOP EXTENSION INSTRUCTIONS STEP 1 Lift up the Leaf Top. I 1 1 1 1 1 1 1 1 1 1 1 1 1 1 : II STEP2 Holding the Leaf Top up, pull out a back leg from the unit; then pull out the other back leg.
PAGE 8
Assembly Instructions 8/9 Drawer (0) STEP 1 l',, ',, '' ' +--11/4" Flat Head Screw Attach Side Part (03) to Front Part (01) and Back Part (02) using a Phillips screwdriver and 1 1/4" Flat Head Screws. Make sure roller is on the back STEP2 Insert Base Part (05) into the groove. Attach Side Part (04) to Front Part (01) and Back Part (02) using a Phillips screwdriver and 1 1/4" Flat Head Screws. STEP3 Attach Pull Handles with Machine Screws. Part List 01. Front Part 2 pcs � 2 pcs.
PAGE 9
Assembly Instructions 9/9 L == =o __J II n I ' -i_ d= ;; I. IF A DRAWER DOES NOT ALIGN STEP 1 Loosen slighty the upper screws. 0 0 � STEP2 ... � �\ �/ l"1 .. ,' \ I /I I � ''';_ D= (1 Insert the drawer into the main body, then adjust the drawer front panel left or right and up or down, until the drawer gaps look proportional. � 11. IF A DRAWER ALREADY ALIGNS STEP3 Pull out drawer slowly. Lock the drawer front panel into position with 3/4" Flat Head Screws.
PAGE 10
VERY IMPORTANT !! CARE INSTRUCTIONS NEVER NEVER USE GLASS CLEANERS ON FINISHED FURNITURE. AMMONIA WILL CHEMICALLY ATTACK THE LACQUER. ALLOW LIQUIDS OF ANY KIND TO REMAIN ON THE FURNITURE. ABSORPTION CAUSES WOOD TO WARP AND SPLIT AND FINISHES TO DELAMINATE. DO NOT WRITE DIRECTLY ON SURFACE. DO NOT PLACE IN DIRECT SUNLIGHT. PREVENT FADING PREVENT MARKING DO NOT USE COMMERCIAL WAXES AND POLISHES. PREVENT YELLOWING DO NOT PLACE HOT OBJECTS ON SURFACE.