User Manual
Table Of Contents
- Index
- 1. Product description / Precautions
- 2. PACKAGE CONTENTS
- 3. AP F8.9 bit and DRC INSTALLATION
- 4. CONNECTION PANELS - DESCRIPTION
- 5. CONNECTIONS
- 5.1 POWER SUPPLY AND REMOTE TURN ON
- 5.2 INPUT SIGNALS
- 5.3 DIGITAL OPTICAL IN INPUT
- 5.4 OUTPUT SIGNALS
- 5.4.1 PRESET 0 DEFAULT: 3 WAY ACTIVE FRONT + REAR + EXTERNAL SUBWOOFER
- 5.4.2 PRESET 1: 2 WAY ACTIVE FRONT + 2 WAY PASSIVE REAR + SUBWOOFER
- 5.4.3 PRESET 2: 3 WAY ACTIVE FRONT + SUBWOOFER
- 5.4.4 PRESET 3: FRONT + REAR + SUBWOOFER
- 5.4.5 PRESET 4: 2 WAY ACTIVE FRONT + REAR + SUB
- 5.4.6 PRESET 5: 3 WAY ACTIVE FRONT + REAR + EXTERNAL AMPLIFIED SUB
- 5.4.7 PRESET 6: 2 WAY ACTIVE FRONT + REAR + EXTERNAL AMPLIFIED SUB
- 5.4.8 PRESET 7: 2 WAY ACTIVE FRONT + REAR + 2 WAY CENTER CHANNEL + EXTERNAL AMPLIFIED SUB
- 5.5 PC CONNECTION AND DIGITAL REMOTE CONTROL (DRC)
- 6. GUIDE FOR INSTALLING/UNINSTALLING AP F8.9 bit SOFTWARE AND DRIVERS
- 7. HOW TO SET UP AP F8.9 bit WITH A PC
- 7.1 OFFLINE MODE
- 7.2 TARGET MODE
- 7.3 ADJUSTING ACOUSTIC REPRODUCTION
- 7.3.1 DEVICE INFO
- 7.3.2 FILE MAIN MENU
- 7.3.3 MEMORIES MAIN MENU
- 7.3.4 SETTINGS MAIN MENU
- 7.3.5 DEVICE MAIN MENU
- 7.3.6 HELP MAIN MENU
- 7.3.7 SELECTED INPUT
- 7.3.8 CHANNEL MAP
- 7.3.9 SELECT CHANNEL
- 7.3.10 FILTER SETTINGS
- 7.3.11 SET DISTANCE AND DELAY
- 7.3.12 PARAMETRIC EQUALIZER
- 7.3.13 OUTPUT LEVEL
- 7.3.14 MEMORY
- 7.3.15 STATUS BAR
- 8. TROUBLESHOOTING
- 9. ACCESSORIES
- 10. Technical specifications
34
AP F8.9 bit /
USER’S MANUAL
9. Speaker Connection Setup.
The speakers available in the system can be activated
by simply clicking on them.
The software assumes that if the Left tweeter, midrange or
woofer are selected, the Right ones are also activated.
Once the software is started, this choice will affect
the crossover type and frequencies with Default settings.
If passive crossover filters are not used, each speaker
corresponds to an output channel.
If the sum of the crossovers and/or speakers exceeds
the occupation of 8 PRE output channels, the software will not
allow you to proceed with the next operation. Check again the
configuration of the crossovers or, using BACK, the speakers setup.
Select Bridge Mode outputs for groups of speakers.
In order to increase the driving power of the speaker output,
set AP F8.9 bit outputs to BRIDGE mode, selecting the check mark as
indicated in the image.
Press BACK to return to the previous step.
Press NEXT to continue with the configuration.
Press CANCEL to exit the procedure.
WARNING: a coaxial speaker is considered a as
Tweeter + Woofer + 2 way passive crossover.
Selection of passive crossovers for groups of speakers
The presence of passive crossovers managing functional speaker
groups can be indicated.
E.g.: If the audio system features passive crossovers, the software will
ask you to set them by clicking on
, otherwise press NEXT.
A 2 or 3 way passive crossover occupies a single output channel.
7