VM9410 Owner’s Manual 7-INCH TFT OPEN VM9410 AV AUX IN DVD-R VM9410 Push ENTER 2-6CH PWR LO/DX SRC
CONTENTS Tuner Operation................................................................................... 14 Thank you for choosing a Jensen product. We hope you will find the instructions in this owner’s manual clear and easy to follow. If you take a few minutes to look through it, you’ll learn how to use all the features of your new Jensen VM9410 Mobile Multimedia AM/FM/DVD Receiver for maximum enjoyment. Tuner TFT Display ...............................................................................
VM9410 PREPARATION Congratulations on your purchase of the Jensen VM9410 Mobile Multimedia AM/FM/DVD Receiver. It’s a good idea to read all of the instructions before beginning the installation. We recommend having your Jensen VM9410 installed by a reputable installation shop. Features 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 1 DIN Size. Ultra slim slot-in DVD core mechanism. 7 inch Panasonic TFT monitor. Built-in 4X40W power amplifier audio output.
VM9410 INSTALLATION Pre-installation 1. 5. Press the metal levers on both sides to remove the halfsleeve from the radio. Remove the transport screws. 2. 1 CH DIGI TAL 7-IN TFT CH TFT BAN D AS/P S 510 AM/ FM/ MUTE DVD /MP 3 REC FINAL INSTALLATION Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve. EIVE 4 5 1 Complete wiring as illustrated in the wiring diagram on page 3.
VM9410 WIRING DIAGRAM CD Changer IP-BUS Cable / BLACK GREY CD Changer compatible with SANYO disc changers CENTER Wireless Headphone BLUE WHITE SUB.
VM9410 CONTROLS AND INDICATORS Button Operation 14 1. OPEN 26 23 Press the OPEN button (1) to activate the automatic mechanical system and move the TFT monitor into viewing position. 7-INCH TFT 2. WIDE/PICTURE 5 1 VM9410 Press the WIDE/PICTURE button (2) to adjust the display aspect of the picture to one of three settings: Wide, Full or Normal. 3. ( ) Press the button (3) to adjust the upward tilt angle of the screen one step at a time.
VM9410 CONTROLS AND INDICATORS 10. 3/SCN 14 DVD Mode: Press once to start scan playback. TUNER Mode: Press once to play preset radio station channel 3. Press and hold to store the current radio station in preset channel 3. 26 23 7-INCH DIGITAL TFT 11. 4/REP 7-INCH BANDTFT DVD Mode: Press once to start repeat playback. TUNER Mode: Press once to play preset radio station channel 4. Press and hold to store the current radio station in preset channel 4.
VM9410 CONTROLS AND INDICATORS LCD Display/Indicators 1. Disc Indicator Illuminated when disc is loaded 2. DVD Playback Indicators (SCN/RPT/RDM/ALL) The following DVD playback indicators become Illuminated when the corresponding function is active: • • • • SCN: scan playback RPT: repeat playback RDM: random playback ALL: playback all chapters 1 2 3 3. Loudness Indicator (LOUD) The loudness indicator becomes illuminated when the LOUD function is activated. 4.
VM9410 FRONT ZONE REMOTE CONTROL Table 1: Front Zone Remote Control Functions Button Name MENU TITLE Function Ref # 1 2 DVD VCD Enters the main menu of the disc Turns on PBC when playing VCD Enters the title menu of the disc Plays first ten seconds of each chapter/title CDC TUNER CD/MP3 MUTE 3 Toggles on/off audio output Toggles on/off audio output Toggles on/off audio output Toggles on/off audio output Toggles on/off audio output POWER/ 4 Turns the power on/off Turns the power on/off
VM9410 Table 1: Front Zone Remote Control Functions Button Name Function Ref # DVD VCD CDC TUNER CD/MP3 22 Slow playback/slow rewind playback Slow playback/slow rewind playback ZOOM 23 Zooms in/out on an image Zooms in/out on an image PIC 24 Displays set-up parameters Displays set-up parameters OPEN/ CLOSE 25 Opens/Closes the TFT monitor Opens/Closes the TFT monitor Opens/Closes the TFT monitor Opens/Closes the TFT monitor Opens/Closes the TFT monitor 26 Decreases monitor tilt angl
VM9410 REAR ZONE REMOTE CONTROL Table 2: Rear Zone Remote Control Functions Button Name Function Ref # DVD VCD MENU 1 Enters the main menu of the disc Turns on PBC when playing VCD TITLE 2 Enters the title menu of the disc Plays first ten seconds of each chapter/title MUTE 3 Toggles on/off audio output Toggles on/off audio output AUDIO 5 Switches the audio language for disc playback REPT 7 Setup to repeat playback of each chapter/title/disc Setup to repeat playback of each chapter/titl
VM9410 USING THE TFT MONITOR Open/Close TFT Monitor FULL The entire screen is extended horizontally to the aspect ratio of 16 to 9. The extension ratio is the same at any point. Open TFT Monitor Press the OPEN button (1) on the front panel or press the ( ) button (25) of the front zone remote control to activate the mechanism that moves the display panel into the viewing position. WIDE The screen is extened horizontally to the aspect ratio of 16 to 9.
VM9410 OPERATING INSTRUCTIONS Power On / Off Audio Control Menu Exiting the Audio Control Menu Press the /MUTE button (1) to turn the unit on. The buttons on the front of the unit light up and “WELCOME” appears briefly in the LCD panel (17), followed by the current mode status. If the TFT screen is open, only the current mode status is displayed. You can also turn on the unit by pressing the OPEN button (2) and opening the TFT screen.
VM9410 SYSTEM SETUP MENU In “System Setup” mode, “ASP CONFIG” and “GENERAL SETUP” are available for adjustment. Setup can be performed by pressing the dedicated button on the remote control or on the front panel. For system settings, press the SYS SETUP button (31) on the remote control to enter the “System Setup” menu. “ASP CONFIG” is highlighted in green.
VM9410 Table 8: ASP Config Menu Features ASP Config Setting Sub.W Filter Options 80Hz 120Hz 160Hz Sub.W Phase Function Selecting a crossover frequency sets a cut-off frequency of the subwoofer's LPF (low-pass filter) and the “SMALL” speakers' HPF (high-pass filter). The Crossover frequency setting has no effect if the subwoofer is set to “OFF” and any other speaker is set to “LARGE”.
VM9410 TUNER OPERATION Tuner TFT Display 4 1 11 5 2 6 P1 ST Switch to Radio Tuner source Auto Store (AS) Press the SRC button (15) on the front panel or remote control (8) to switch to the RADIO TUNER source. The Tuner TFT or LCD display appears. Automatic Storing of Preset Stations Select FM/AM Band 1. 2. Press the BAND button (14) on the front panel or the remote control (20) to change between the following bands: FM1, FM2, FM3, AM1, and AM2.
VM9410 DVD PLAYER OPERATION NOTE: When properly installed, DVD video cannot be displayed on the main TFT screen unless the parking break is applied. If you attempt to play a DVD while the vehicle is moving, the TFT screen displays “PARKING” with a blue background. Rear video screens, if applicable, will operate normally. mode. You may eject a disc with the power off and the unit remains off after the disc is ejected. control to activate random playback and play all chapters/ tracks in random order.
VM9410 • playback. Depending upon the channel selected and your speaker setup, the audio output varies according to the following table. For VCD mode, press the GOTO button to choose between Track Search, Disc Search and Exit.
VM9410 • Rear: AUX IN – “AUX IN” is the current playing source for the rear zone. “Surround” is the current playback audio encoding system. “DSP” indicates Digital Signal Processing.
VM9410 DVD SETUP MENU In “DVD Setup” mode, “LANGUAGE”, “VIDEO”, “AUDIO”, “SURR SETUP”, and “RATING” (parental lock) are available for setup. This operation can be performed using the remote control or joystick controls. 3. Accessing the DVD Setup Screen LANGUAGE Menu For system settings, press the DVD SETUP button (31) on the remote control to enter the “DVD Setup” menu. “LANGUAGE” is highlighted in green.
VM9410 Table 14: AUDIO Menu Features Setting REAR CTRL Options 15ms Function Adjust the time difference between the rear and front speakers to create a time delay between 3 and 15 milliseconds, producing a more accurate audio effect.
VM9410 CD PLAYER/CHANGER OPERATION Instructions for Insert/Eject, Play/Pause, Stopping Playback, Track Selection, Fast Forward/Fast Reverse, Scan, and Random Play are the same for DVD, CD, CD Changer and MP3 operation. Please see the DVD Player Operation section for information about these topics. NOTE: Upon inserting a disc with the TFT screen open, the disc and track title (if available), along with the track number and playing time appear on the screen. Selecting a Playback Mode 1.
VM9410 TROUBLESHOOTING Table 18: Troubleshooting Problem Cause Corrective Action GENERAL Unit will not power on Remote control does not function No/low audio output Poor sound quality or distortion Radio Fuse blown Install new fuse with correct rating Car battery fuse blown Install new fuse with correct rating Illegal operation Press the RESET button located in the bottom right corner of the front panel Battery depleted Replace battery with new one Battery installed incorrectly Remove batter
VM9410 Table 18: Troubleshooting Problem Disc does not play back Cause Corrective Action Disc is warped or scratched Use disc in good condition Disc is dirty or wet Clean disc with soft cloth Laser pickup is dirty Clean laser pickup with cleaning disc Incompatible disc is used Use compatible disc Disc rating exceeds Parental Lock rating limit Change Parental Lock settings to lower restriction Disc region code is not compatible with unit Use disc with proper region code Disc is inserted upside
VM9410 SPECIFICATIONS Frequency Response: 30Hz - 15kHz, -3dB AM Tuner Tuning Range: 530kHz - 1720kHz Sensitivity (-20dB): 30uV Signal to Noise Ratio @ 1kHz: 50dB Image Rejection: 60dB Frequency Response: 50Hz - 2kHz, -3dB CEA Power Ratings Power Output: 13 watts RMS X 4 channels into 4-ohms @ < 1% THD+N Signal to Noise Ratio: 70dBA below reference. (Reference: 1 watt, 4-ohms) Dynamic Power: 64 watts into 4-ohms, all channels driven Frequency Response: 20Hz to 20kHz, -3dB.
