Owner's Manual

ManualsBrandsAudiovox ManualsAudio accessories & installationVoxx

LINCOLN / NAVIGATOR/2018-19 SB10UHD 10.1” SEAT-BACK ENTERTAINMENT SYSTEM

Page 1 of 10

730144A3

Document #730155 Created ACH 04/15/2019

Revised ACH 04/15/2019– A1

Kit Contents:

Item #

Qty.

Component Description

Monitors

SB10MD1 monitor with DVD

SB10M1 monitor without DVD

Harnessing

L Connector Cable

T Junction Cable

Brackets

Metal Shaft Bracket

Metal Stent Bracket

Plastic Spacer

Plastic Trim Cover

Miscellaneous

Screw Cover

Screw Pack

Owner’s Manual

Installation Manual

Voxx Registration Card

Navigator Bracket Contents:

Item #

Qty.

Component Description

SBK-LINC

201446 Bracket

540040 Pre-pack

Additional Items Required For Installation:

Item #

Qty.

Component Description

Recommended Tools:

Safety Tools

Seat/ Floor Covers

Blankets

Installation Tools

7mm Socket/Ratchet

Flathead screw driver

11mm Socket/Ratchet

Side Cutters

NRT-Nylon Removal Tool

Razor Knife

10mm Open end wrench

Special Tools

Dremel tool w/ cut wheel

Color Applicability/ Trim Level:

Vehicle Trim Color

Accessory

Color

General Applicability:

2018-19 Lincoln Navigator - 24 and 30-way seat

Conflicts:

2018 Lincoln Navigator - 10-way seat (Headrest available)

LEGEND:

STOP: Damage to the vehicle may occur. Do not

proceed until process has been complied with.

OPERATOR SAFETY: Use caution to avoid risk of

injury.

CRITICAL PROCESS: Proceed with caution to

ensure a quality installation. These points will be

audited on a completed vehicle installation.

TOOLS & EQUIPMENT: This calls out the specific

tools and equipment required for this process.

REVISION MARK: This mark highlights a change

in installation with respect to previous issue.

INSTRUCTION / INSTALLATION NOTES:

• After Safety mandated preparatory steps have been

taken, the installation sequence is the suggested method

for completing the accessory installation.

• When prying panels, use masking tape on all surfaces

that a tool may come in contact with to prevent marring.

• After a wire tie is fully fastened, cleanly cut excess wire tie

length with a pair of wire cutters.

• The wiring information is on an “as is” basis without any

representation or warranty. It is the installer’s

responsibility to verify any circuit before interfacing with it

using a digital multi-meter.

• Manufacturer’s service documents can be used for any

vehicle disassembly that may be depicted differently from

what the instruction states.

• Use Wiring Diagram on last page of document to clarify

cable or component names.

Summary of content (10 pages)

PAGE 1
LINCOLN / NAVIGATOR/2018-19 SB10UHD 10.1” SEAT-BACK ENTERTAINMENT SYSTEM Document #730155 1 1 1 Color Applicability/ Trim Level: Component Description Monitors SB10MD1 monitor with DVD SB10M1 monitor without DVD Harnessing L Connector Cable T Junction Cable Brackets Metal Shaft Bracket Metal Stent Bracket Plastic Spacer Plastic Trim Cover Miscellaneous Screw Cover Screw Pack Owner’s Manual Installation Manual Voxx Registration Card Accessory Color Kit Contents: Item # Qty.
PAGE 2
LINCOLN / NAVIGATOR/2018-19 SB10UHD 10.1” SEAT-BACK ENTERTAINMENT SYSTEM A. Pre-Installation Precaution Figure B1a 1. Use Seat and Floor protectors to avoid damage to surfaces. Disconnecting the battery prior to any ground or harness removal/ tapping to prevent possible vehicle damage is recommended. The battery may be temporarily reconnected and disconnected throughout the installation process to perform various tasks.
PAGE 3
LINCOLN / NAVIGATOR/2018-19 SB10UHD 10.1” SEAT-BACK ENTERTAINMENT SYSTEM 3. On both sides of the seat, grasp the back panel Fig B3 where it meets the front trim, pull to release the clips and separate the back panel from the front. (Figure B3) 4. On both upper sides, using an NRT, pry in Figure B4 between the seat back and the front trim to release clips. (Figure B4) 5. Pull out on the bottom of the seat back panel releasing the 2 lower clips.
PAGE 4
LINCOLN / NAVIGATOR/2018-19 SB10UHD 10.1” SEAT-BACK ENTERTAINMENT SYSTEM 6. Using your fingers, press the retaining clips Figure B6a toward each other to release the front head restraint posts. Lift and remove the front head restraint. NOTICE: Figure B6c show the clips after the head restraint has been removed to show location. (Figure B6a-c) Figure B6b 7. Repeat steps B1-6 on the opposite seat. Figure B6c C. Head Restraint Trim Preparation Figure C1a 1.
PAGE 5
LINCOLN / NAVIGATOR/2018-19 SB10UHD 10.1” SEAT-BACK ENTERTAINMENT SYSTEM Figure C1c 2. Protect the vinyl surface by laying tape across Figure C2a the edge of the rear trim cover. Using a marker, draw a line from side to side on the rear side of the chrome. Also mark lines just before the clips. Using a Dremel cut off wheel, trim the excess chrome and plastic behind chrome from the rear Figure C2b trim cover. (Figure C2a-d) Figure C2c Figure C2d © 2018 Voxx Automotive, Inc. All rights reserved.
PAGE 6
LINCOLN / NAVIGATOR/2018-19 SB10UHD 10.1” SEAT-BACK ENTERTAINMENT SYSTEM 3. Using a Dremel, cut outer chrome the width of Figure C3a the rear seat entertainment bracket. Use bracket to determine the cut area. Use a pliers to finish breaking away the chrome piece. Make sure there is no obstructions blocking the rear of the trim panel. Test fit onto seat to check for Figure C3b clearance. (Figure C3a-c) Figure C3c 4.
PAGE 7
LINCOLN / NAVIGATOR/2018-19 SB10UHD 10.1” SEAT-BACK ENTERTAINMENT SYSTEM D. Monitor Bracket Installation Figure D1a 1. Slide hooks of the rear seat entertainment bracket into the openings of the seat frame. Using the bolts provided, insert to hold bracket in place. Install nut to rear side of bolt and tighten using a 11mm socket and ratchet. Figure D1b (Figure D1a-c) Figure D1c 2. Make sure monitor cable is routed as pictured, Figure D2a from rear of monitor and between the metal tabs.
PAGE 8
LINCOLN / NAVIGATOR/2018-19 SB10UHD 10.1” SEAT-BACK ENTERTAINMENT SYSTEM 3. Continue routing cables to lower seat and Figure D3a securing with supplied wire ties. (Figure D3a-b) NOTE: before installing seatback cover, you want to test fit the head restraint for cut out clearance. Make sure the rear cover locks into the bracket. Figure D3b 4. Re-attach the rear seatback cover in the reverse removal process. Make sure that the 2middle clips engage into the seat frame properly.
PAGE 9
LINCOLN / NAVIGATOR/2018-19 SB10UHD 10.1” SEAT-BACK ENTERTAINMENT SYSTEM E. Harness Routing -Power/Ground Location Figure E1 1. Route seat harness from seat bottom following the factory harness down and into carpet opening. Route harness over to center console at break in carpet. (Figure E1a) 2. On driver side, using a wire pull, route driver Figure E2a harness under center console to passenger side. (Figure E2) 3. Connect Driver and Passenger seat harnesses Figure E3a to T-Harness.
PAGE 10
LINCOLN / NAVIGATOR/2018-19 SB10UHD 10.1” SEAT-BACK ENTERTAINMENT SYSTEM 4. In small opening along passenger side of the Figure E4a center console, reach into the opening you will find a connector with power and ground. This is the factory connector for rear seat entertainment. (Figure E4a-b) Figure E4b 5. Make all connection to Power and Ground using Figure E5 a Voltage Stabilizer. (Figure E5) 6. Once all connections have been made, turn on the vehicle and test the system. F.