User manual

WAIT/PAUSE FEATURE
Pauses are used for automated systems (i.e., voice mail or calling cards).
Insert a pause after a phone number and then enter another group of
numbers. The second set of numbers is dialed automatically after the pause.
This feature is useful for dialing into systems that require a code.
Hard Pause (P)
The phone stops dialing until you press the OK Key
[SEND] to advance to
the next number.
2 Sec Pause (T)
The phone waits 2 seconds before sending the next string of digits
automatically.
1. Slide out the QWERTY keyboard, and from standby mode enter the
phone number.
2. Press the Right Soft Key
[Options].
3. Press the Directional Key
up or down to select pause type, then
the OK Key [OK]. “2 Sec Pause/Hard Pause”.
4. Enter additional number(s) (pin number or credit card number).
5. Press the SEND Key
to dial or the Left Soft Key [Save].
ANSWERING A CALL
1. If your phone is set to “Slide Open” for “Answer Options,” simply
open the phone to answer a call. If your phone is set to “Any Key” for
“Answer Options,” press any key to answer a call.
If your phone is set to “Auto Answer” for “Answer Options,” calls are
answered automatically with a 5 second delay. If your phone is set
to “Send Key” for “Answer Options,” only press the SEND Key
to
answer a call. For information on how to set your Answer Options,
see page 56.
2. To end the call, press the END Key
.
MAKING AN INTERNATIONAL CALL
1. Slide out the QWERTY keyboard, and then press and hold the * Key
. The + required for international calls will be displayed.
2. Enter the country code, area code, and phone number, then press
the SEND Key
.
3. To end the call, press the END Key
.
18 Chapter 2 − Basic Operation
Basic OperationBasic Operation
3WAY CALLING
With 3-Way Calling, you can talk to two people at the same time. When using
this feature, the normal airtime rates will be applied for each of the two calls.
1. Slide out the QWERTY keyboard, enter the phone number you wish to
call, then press the SEND Key
.
2. Once you have established the connection, enter the second phone
number you wish to call and then press the SEND Key
again.
3. When you’re connected to the second party, press the SEND Key
again to begin your 3-Way call.
If one of the people you called hangs up during your call, you and the remaining caller
stay connected. If you initiated the call and are the first to hang up, all three calls are
disconnected.
CALL WAITING FUNCTION
If you are on a call and you receive another incoming call, you will hear two
beeps and the caller’s phone number will appear on the display. With Call
Waiting, you may put the active call on hold while you answer the other
incoming call. To use Call Waiting:
1. To answer another call while on the phone, press the SEND Key .
This places the first call on hold. To switch back to the first caller,
press the SEND Key
again.
CALLING A NUMBER FROM PHONEBOOK
1. From standby mode, press the OK Key [OK] to unlock the keypad,
then press the Right Soft Key [Phonebook].
2. Press the Directional Key
up or down to select the Phonebook
entry then press the OK Key [VIEW].
3. Press the Directional Key
up or down to select the phone
number.
4. Press the SEND Key
to place the call.
Pressing the Directional Key up or down to select the “LIST ENTRIES” and then
pressing the SEND Key will automatically dial the Default Number of the Phonebook
entry. If multiple numbers are saved in the “LIST ENTRIES”, press the Directional Key
up or down to select the “LIST ENTRIES” and then press the Directional Key left
or right to select the number you want to dial. Then press the SEND Key
.
Basic Operation − Chapter 2 19
Basic OperationBasic Operation
081027_TXT8010_ELVIS_MV_M_EN_REV03.indd 18-19081027_TXT8010_ELVIS_MV_M_EN_REV03.indd 18-19 2008.11.3 5:4:49 PM2008.11.3 5:4:49 PM