6 COMPACT DISC AUTO CHANGER MODEL : PAV-6CDP ’ OWNER’ S MANUAL
* Tracks from 6 CDs stored in the disc magazine can be selected and played. * Horizontal, vertical, angled and suspended installation. * Do not install the unit in a location where it may be subjected to : - direct sun or other forms of excessive temperature. - excessive heat. - fluid, rain or moisture. - excessive dirt or dust. - excessive vibration. * This unit is designed to be operated on a 13.8 volt DC negative ground electrical system only.
* Do not expose the discs to direct sunlight or excessive heat. * Clean the discs before inserting them into the disc magazine. Always clean a disc from center outward with a cleaning cloth. * Never use solvents such as benzine or alcohol to clean a disc. * You cannot play an 8cm(3 inch) CD even with the specially designed adapter. Notes on the disc magazine * Do not leave the disc magazine in a place subject to excessive temperature or humidity. * Do not insert more than one disc per slot.
1. * Pull out the slot by pulling the part with finger. 3. Insert the magazine firmly (which has been taken out of the unit) with the mark visible on the top side. * With the label side up, insert a CD all the way 6 discs, one in each slot * Push slot and close it. * Press the eject button and pull out the disc magazine. 2. 4.
Supplied mounting kit BRACKET X 2 WASHER SCREW X 4 Double-sided tape X 1 PLATE BRACKET TAPPING SCREW X 4 BOLT X 4 Adhesive label X 1 NUT X 4 Precautions Select the mounting location very carefully by referring to the following points * Make sure that there is not a fuel tank, wiring or piping on the other side of the mounting surface. * Make sure that the installation of the unit will not hinder the movement of the trunk lid or interfere with the spare tire etc.
Removing screws the transport Find the 3 transport screws at the bottom of the unit, which lock the unit’s mechanism during transport. Remove these screws before installation and attach the supplied adhesive labels ④ over the holes. Retain these screws and replace them in the original positions if the unit is transported for service or maintenance. Installing the unit Mounting angle setting lever Be sure to adjust Mounting Angle Setting Lever(A) to appropriate angle; 0°for horizontal, 22.
After adjustment, be sure to attach the Double side Tape . Making holes on the carpet Note Do the same procedure on the other side of the unit. Horizontal installation Completion Construction Note About parts numbers ❶❷ ❺ ❻ ❼ ❽ ,refer to page 4. angled installation Removing temporarily Be sure to turn the mounting angle setting dial to the 45。 position.
Vertical installation 3. Making holes on the carpet 1. Construction 4. Completion 2. Removing temporarily Note About parts numbers ❶ ❷ ❺ ❻❼❽, refer to page 4.
Suspended installation When installing the unit in the trunk under the rear window shelf, observe the following. - Make sure that the unit is suspended horizontally. - Select the mounting location carefully so that the unit does not hinder the movement of the torsion bars of the trunk lid. - Make sure that there is nothing on the other side of the mounting location before drilling the holes. - Select the correct size screw to avoid damaging the vehicle rear deck. 2. Making holes 3. Completion 1.
When connecting, run the supplied connecting cable and connect to Audiovox model PAV-9 as illustrated here. Caution Make sure to disconnect the ground wire terminal of the car battery before making a connection in order to prevent short circuiting. Note Use only the supplied connecting cable. For complete operation instructions, refer to pages 18,19 and 20 in the PAV-9 owner’s manual. General System Usable Disc Power Source Weight Dimensions(W XH X D) Frequency Response S/N Ratio Channel Separation T.H.
12 MONTH LIMITED WARRANTY Applies to Audiovox Video products AUDIOVOX ELECTRONICS CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original purchase, such defect(s) will be repaired or replaced with reconditioned product (at the Company’s option) without charge for parts and repair labor.
