MZ7TFT Installation and Operation Manual MZ7TFT TOUCH PANEL 7-INCH TFT LCD IR POWER AV-IN
Introduction Thank you for purchasing the Audiovox MZ7TFT Touch Screen Monitor. This package contains (1) one MZ7TFT, Installation and Operation Manual, mounting bracket with tool, wiring harness, touch screen expansion module and a three year limited warranty. Toll-Free Installation Assistance If you require assistance, contact Technical Support at 1-800-645-4994 from 9:00 a.m. to 6:00 p.m. EST Monday through Friday (U.S.A. and Canada only).
MZ7TFT Wiring 1. Align the ridges on either end of the combined input cable (VIDEO IN, AUDIO L, AUDIO R, REAR TS, GROUND and ACC) and connect the cable to the male connector on the back of the MZ7TFT. The connector will only fit when the notched areas are properly aligned. 2. Connect the REAR TS connector to the MZ7-TFT connector on the back of your compatible head unit (if applicable).
MZ7TFT Touch Screen Expansion Module 1. Connect the AUDIO R and AUDIO L cables from the MZ7TFT to the Multizone Headphone cables on the back of your compatible head unit. 2. Connect the VIDEO IN cable from the MZ7TFT to the Video Out cable on the back of your compatible head unit. HEAD UNIT 3. Connect the MZ7-TFT connector from the back of your compatible head unit to the REAR_TS_OUT connector on Side 1 of the Expansion Module. 4.
MZ7TFT Installation/Mounting Figure 2: Attach Bracket/Secure Bracket 1. Insert the metal end of the center arm on the mounting bracket into the slot on the back of the monitor. 2. Turn the large plastic nut to secure the bracket to the monitor. Figure 3: Install Headrest/Tighten and Adjust 3. Tighten the smaller plastic nut to further secure the bracket. 4. Install the headrest through the holes in the headrest mounting pieces on either end of the mounting bracket. 5.
MZ7TFT Operation Power On/Off/Standby NOTE: Your head unit must be compatible with the MZ7TFT touch screen capability for the IR remote repeater function to work. The input allows voltage ranges from DC 10.8V to 16V, which includes the DC 12V car power supply. After connecting the power, the monitor will be in standby mode. Press the POWER button to turn the monitor on. Press and hold the POWER button to return the unit to standby mode. 4. Touch Screen Controls and Indicators 5.
MZ7TFT • Selecting the Input Signal channel, and each MZ7TFT must be set to transmit on the same channel as the headphone (i.e., left seat monitor/headphones set to channel A and right seat monitor/headphones set to channel B). This will prevent interference of audio by the IR signal being transmitted from two monitors on the same channel. This is inherent in Infrared Ray communication and does not mean there is a problem with the MZ7TFT itself.
MZ7TFT Care and Maintenance • • • • • Do not remove the rear panel of this product. If in need of service, please call a qualified technician. Keep away from strong light while using this product so as to obtain the clearest and the most colorful picture. Avoid heavy impact, do not drop. Do not use chemical solutions to clean this unit. Please wipe with a clean soft cloth to keep brightness of the surface. Do not expose this product to direct sunlight, heat or humid conditions.
Limited Warranty Audiovox Electronics Corporation (“the Company”) is committed to quality and customer service, and are pleased to offer you this Warranty. Please read it thoroughly and contact the Company at 1-800323-4815 with any questions. Who is covered? The Company extends this warranty to the original retail purchaser of products purchased through an authorized Audiovox retailer in the U.S.A., Puerto Rico or Canada. This warranty is not transferable or assignable.
Audiovox Electronics Corporation Hauppauge, NY 11788 Technical Assistance: 1-800-645-4994 www.audiovox.com © 2008 Audiovox Ver.
