® ELECTRONICS CORP.
IMPORTANT An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or navigation. If the LCD panel or video monitor is used for television reception, video or DVD play, the LCD panel or video monitor must be installed so that these features will only function when the vehicle is in ‘park’ or when the vehicle’s parking brake is applied.
The Materials included in this package 1. 2. 3. 4. 5. 6. LCM7020PKG System Monitor (One Master-#LCM7020M, One Slave-#LCM7020S) Master Remote Control Unit (MRCU) #136B3439 Slave Remote Control Unit (SRCU) #136B3440 System Main Cable (SMC) #1123277 Dual Frequency IR Headphone set (#IR2CHS) FM Modulator package (#FMM100/IST2) 1. (2pcs) (1pc) (1pc) (1pc) (2pcs) (1set) 2. M aster M onitor 3.
LCM7020PKG SYSTEM OVERVIEW 1) The LCM7020PKG is a versatile audio/video system which includes two monitors, that can accept two Audio/Video inputs. A separate audio output is provided for connecting the FM Modulator to the vehicle's radio. 2) The Master Monitor is comprised of a 7" TFT LCD monitor that allows the user to select from two A/V sources (Not Supplied). The Master monitor has built-in infrared audio transmitter (CH A) for use with the supplied two channel wireless headphones (CH A).
VEHICLE PREPARATION: 1) Decide on the system configuration and the options that will be installed (i.e.what components, VCP, DVD, TV Tuner, Video Game, FM Modulator, etc.). 2) Read the manuals and get familiar with the electrical requirements and connections. 3) Decide on the mounting locations and methods of mounting the products that will be connected to the LCM7020PKG.
CABLE TERMINAL INSTALLATION Master & Slave Monitor 3 4 2 SHRINK SLEEVES -4-
LCM7020PKG SYSTEM WIRING DIAGRAM POWER S TOP/EJECT AUTO REPEAT SENSOR REW PLAY F FWD 1.) Make sure the Master, and Slave monitor have been installed properly, as described in the procedures as stated on page 3. 2.) Connect the four JST terminals of the System Main Cable to the corresponding JST terminals of Master Monitor and Slave monitor on the bottom of the seats. Label the JST terminal of System Main Cable Master and connect them to the Master monitor.
Controls on Master Monitor and Master Remote Control Unit Master Monitor Panel Controls 1 2 3 POWER SOURCE WIDE 4 5 6 7 8 1 2 3 4 5 6 7 8 MENU VOLUME POWER On / Off Button SOURCE Button WIDE button Infrared Audio Transmitter MENU Button VOLUME / Select Down Button VOLUME / Select Up Button Remote Control Sensor (IR) Master Remote Control Unit Buttons 1 2 3 4 5 6 7 8 9 10 LCD : Power On / Off Button for Master monitor VCP : Power On / Off Button for Optional Audiovox VCP SOURCE : Button for s
Controls on Slave Monitor and Optional Slave Remote Control Unit Slave Monitor Panel Controls 1 2 3 POWER SOURCE WIDE 4 5 6 7 8 1 2 3 4 5 6 7 8 PICTURE VOLUME POWER On / Off Button SOURCE Button WIDE Button Infrared Audio Transmitter PICTURE Button VOLUME / Select Down Button VOLUME / Select Up Button Remote Control Sensor (IR) Slave Remote Control Unit Buttons 1 2 3 4 5 LCD : Power On / Off Button for Slave monitor SOURCE : Button for selection of AV #1 and AV #2 Menu / Enter – : Volume / S
OPERATION INSTRUCTION Button Functions There are six buttons on the front of the monitor: POWER, SOURCE, WIDE, MENU (Master Only) or PICTURE (Slave Only), VOLUME - and VOLUME +. 1) POWER : Pressing this button will turn the unit on/ off. 2) SOURCE : Pressing this button will select between AV1 and AV2. 3) WIDE : Allows the user to change screen format (Aspect Ratio , 4:3 or 16:9). 4) MENU : This button is only on the Master monitor. Pressing this button, will display the menu OSD.
d) Highlight the SOURCE and press MENU button, OSD as below: SOURCE AV 1 AV 2 Then, you can use VOLUME- or VOLUME+ buttons to select from AV1 or AV2. The Master monitor can also operate the AV sources via the remote control sensor. g) If you select PICTURE, OSD below: NOTE: In NTSC format, TINT is included. In PAL format, the TINT is omitted. NOTE: The unit will automatically select NTSC/PAL according to the input signal format.
BRIGHTNESS 52 BRIGHTNESS IIIIIIIIIIIIIIIIIIIIIII CONTRAST 52 CONTRAST BRIGHTNESS IIIIIIIIIIIIIIIIIIIIIII COLOR 52 COLOR BRIGHTNESS IIIIIIIIIIIIIIIIIIIIIII TINT 00 TINT I The OSD will automatically disappear if no buttons are pressed for 4 seconds.
CAUTION 1. 2. 3. 4. 5. Do not operate the monitor at temperatures below 32°F (0°C) or above 104°F (40°C). Keep the monitor clean and dry. Always seek qualified personnel to perform repairs. Never attempt your own repairs. Do not drop the monitor or expose to strong impacts. Do not expose to direct sunlight for extended periods of time. MONITOR SPECIFICATIONS 1. Type : TFT Active Matrix LCD 2. Display Screen Size : 7 inches diagonally (6.3 inches x 3.6 inches) (W x H) (16x9) 3.
For Customer Service Visit Our Website At W W W .audiovox.com Product Information, Photos, FAQ’s Owner’s Manuals © Copyright 2003 Audiovox Electronics Corp. 150 Marcus Blvd.