1. BASIC OPERATIONS....................................................................................2 2. PHONE LAYOUT ...........................................................................................6 3. SPECIFICATIONS..........................................................................................9 4. GETTING STARTED....................................................................................10 5. MAKING AND ANSWERING CALLS ......................................................
1. BASIC OPERATIONS Please read and fully understand this manual before using your phone. This chapter addresses the basics of setting up your UTSTARCOM phone, its keys and display icons, and charging and proper use of the battery. Installing the SIM Card and Battery Be careful when handling, inserting and removing the SIM card. The card and its contents can be easily scratched or bent. Keep all miniature SIM cards out of the reach of children. 1.
2 .Gently insert the SIM card into the SIM card holder. Make sure that the SIM card is properly inserted and that the golden contact area on the card is facing downward. Switching ON To turn your phone on, press and hold the POWER key 3 .
Once the phone is ON, it will automatically search the network. When the handset is registered in a network, the network name will be displayed on the screen. You are now ready to make and answer calls. If “Please insert SIM card” appears on the display, turn the phone off by pressing and holding the . Following the instructions on page 2, remove the battery and install your SIM card in the designated slot. If a password or PIN code is required, enter the correct password.
DIRECTION Keys and Right/Left Soft Keys: To navigate the main menu or browse menu items from standby mode, press the Direction Key To access the phone book directly, press the Left Soft Key . ! Numeric Keys: Keys from to , , and . are used to dial numbers and enter passwords, English letters, symbols, characters etc. They can also be used to select menus. Press and hold to keys for more than 2 seconds to quickly dial the phone number correspondingly to the shortcut key. (Please see Section 6.
broadcasts). Receiving Prompt Modes Ringer is set to audible ring. Vibrate. mode Ring after vibrate. Mute mode. STK Function Your phone supports the STK (SIM Tool Kit) function, and the menu items are pre-determined by your SIM card provider. In this case, the STK menu will be added automatically to the end of the handset's main menu accordingly. IMEI (International Mobile Equipment Identity) If you turn off the handset and remove the battery, you will see the bar code label at the back of the handset.
2. PHONE LAYOUT This handset has a 128 64 LCD white and black display screen. Antenna Earpiece Main screen Power Call key Left-soft key Right-soft key Direction key Standard keypad Recharge/Data transmission interface Microphone The Front Schematic Layout Note: Call key & Left soft key are actually 2 sides of the same key.
The Back Schematic Layout Wrist strap attachment loop Antenna Battery latch Battery 8
3. SPECIFICATIONS SPECIFICATIONS PARAMETERS Size 79x42x16.
4. GETTING STARTED Charging the battery Your UTSTARCOM Wireless phone is equipped with a Lithium Ion (Li-Ion) battery. Charge the battery before using the phone for the first time. In order to use the battery at its optimum mode, we recommend completely draining the battery once a month. To do so, simply keep your phone on until the battery runs out. To charge the battery, attach it to the phone, then, connect the supplied AC adapter. Make sure the direction sign is facing upward.
Battery standby and talk times are subject to your handset usage and configuration. Type of battery Standby time Talking time Li-ion battery 50-150 hours 150-250 minutes When the battery is low, the handset will give off a warning tone and display “Low Battery” on the screen. When the power is completely drained, the handset will automatically switch off. Note: Use only the battery & charger approved by the manufacture. Only use the battery for its original purpose. Do not dispose of battery in fire.
5. MAKING AND ANSWERING CALLS Making Calls Use the number buttons to enter the phone number. If you enter the wrong digit, press the Right Soft Key to delete the number or press and hold to clear the entire entry. When a call is established, you will hear a connecting prompt tone. Call meter or call charge will be displayed on the screen. If the call does not connect, it might be one of two reasons: ! LINE BUSY: The phone number is busy or the network dos not have a spare line.
To display the latest numbers from standby mode, press and hold the CALL key . To directly dial a number on the list, select the contact with the DIRECTION Key then press the CALL key again. Send the DTMF When DTMF (Dual Tone Multiple Frequency) function is set, the numeric key you entered from the keypad and key will be transmitted to the recipient as DTMF tone. Mute Function To mute the microphone during a call, press the Right Soft Key.
! Mute: To shut off the microphone. ! On/Off DTMF: To enable/disable function for calling another extension. ! Main menu: To access phone book and message menu. ! Conference call: To access conference call. Press the DIRECTION key to switch between the two calls. If the current call is put on hold, another function menu can occur by pressing the Left Soft Key during the call: ! Volume: To adjust sound volume. ! Switch: To hold/activate the call. ! Hang up: To end the current call.
Missed Calls When you miss an incoming call, the missed calls will appear on the display. To access the list and view the call details, press the DIRECTION key and the Left Soft Key . Cell Broadcast When a cell broadcast arrives, the broadcast list will appear on the display. To access the list and read the broadcast(s), press the DIRECTION key and the Left Sot Key . Connect to Voice Mailbox The handset allows you to forward the incoming calls to a voice mailbox.
appear on the screen. If the number is saved in your phone book, the name will also spear on the screen.
6. FEATURES 6.1 Message Functions Your phone supports the Short Message Service, a system dependent feature. Unless it is already included in your service, you may have to subscribe to this feature from your service provider in order to transmit and receive short messages. The handset also supports enhanced Short Message Service (EMS), which means you can receive messages with attachments such as pictures, ring tones and animation.
! Voice reply: To reply to the received message in voice. Outbox: You can read the message(s) here before you send it, ! Write messages: You can create new message(s) in this menu. The 'input text ‘indicator will appear when you choose this function. And you will see the menu below after you have entered text. ! Done: To handle the message. ! Send: To transmit message(s). You can input the phone number ! directly, or press the DIRECTION key ! book list to select the number.
! Delete: To delete the selected files or folders. ! Rename: To rename a selected file or folder. ! New folder: To create a new folder under the current directory. Message settings: To set message parameters, select Message Settings in the Messages Menu. Menu options include: Message Center: Before sending a message, you must enter the number of the local short message service center (provided by the network supplier.) Message Duration: The valid retention time of a message (i.e.
information service sent to all GSM users in a specific locale from the network supplier, such as weather forecast, transportation conditions, etc. ! Read: To read a cell broadcast in this menu. ! Settings: To preset cell broadcast parameters. o Language: To select a language for the cell broadcasts. o Set Info Subject: To preset the band of the cell broadcast. ! User Defined: To define your own subject. ! Current List: To view the existing list.
Call info: Displays call information including, Call costs: ! Last call: the fee of the last call. ! All calls: the fee of all calls. ! Delete all: clear the call charging records. ! Unit cost: inquire and preset the unit of call charges. ! Max cost: inquire the top call charges and setup the max charges. Call timers: ! Last call: To view call time of the last call. ! All calls: To view call time of all calls. ! Delete all: To clear the call time records.
! The icon on the left of the first row displays the memory of the record. The display on the right indicates the storage location of record and the total number of records in the corresponding memory. Search by name: Search for a record by a specific name. Edit: Edit record details such as phone numbers. ! ! Delete: Delete the selected options. ! Add a record: Add a new record in phone book. Add new name: To add a new record in SIM card or handset memory.
you to enter a date, time for the alarm and a ring tone. You will also have the option of adding a Note. ! Set auto on/off: To set the handset to switch on or off automatically. ! List alarms: To view all the set alarm records. ! Delete all: To clear all the set alarm records. Set date : To set the current date for clock. Set time: To set the current time of the clock. Set zone: To preset your current time zone.
! Silent: No ring and no vibration. Edit Profile: Customizes phone settings. ! Ringing volume: To adjust the ringing level. ! Earpiece volume: To set the call volume. Vibrator: To turn vibrating mode on/off ! Keypad tones: To enable/disable touch-tone. ! Low battery warning tone: To set the warning tone on/off. ! DTMF tones: To set on/off to Dual Tone Multiple Frequency. ! Message alert: To enable/disable the alert tone when message(s) arrive.
! Own number: To preset the number of your handset supplied by your network provider. Call settings: ! Show call number: To display your number on the calling party’s screen. This will function correctly only if your network supplier supports it. Minute minder: To prompt you each minute you are on the call to control your call duration. For example, the first prompt will sound 50 seconds into the call, then another will sound at one minute and every minute afterwards.
o Add new network: Refer to your new network provider for MCC code. o Automatic: To automatically search the network. o Manual search: To manually set the network. o Select mode: To select one of the following modes: EGSM/DCS, EGSM/PCS,EGSM only, DCS only, PCS only Security setting: To access this menu, enter the password. SIM password: To turn on/off the SIM card lock or change the PIN Handset lock: To turn the phone lock password on/off.
6.7 Tools Use the DIRECTION key to access the Tools menu. Calculator The calculator in the handset can carry out simple and practical operations. ! * key: To enter or switch the symbols of operation, including plus, subtract, multiply, divide, etc. ! # key: To enter or switch the symbols of operation, including 4 arithmetic operators: decimal, percentage sign, and right and left brackets. Press the Left Soft Key to view the arithmetic result and the Right Soft Key to clear a character.
6.8 Games The handset provides two classic games: Russian and Bricks. Choose a game , then, press the Left Soft Key with the DIRECTION key to confirm. Follow the instructions after choosing a game for setup, game instructions and top score information. Settings The general settings are used for all the games in the handset. ! Sound: To set a game’s sound on or off. ! Light: To set the game's backlight. Be able to set it on or off.
T9 Smart English Entry Method has smart associating function, the more letters key to switch you enter, the more complete words you get. Use , capitalization. For example: pressing enter the word “ best ”. Press the CALL key not the one you want to enter. , , key will to search if the displayed word is ABC Entry Method ABC Entry Method has no associating function. Enter a corresponding letter with each touch.
8. SAFETY AND PRECAUTIONS ! ! ! ! ! ! ! ! ! ! ! ! ! ! Do not touch the antenna of the handset unnecessarily; doing so may affect the sound quality of the call. Switch your mobile phone off when in the vicinity of chemical plants, gas stations and other explosives. Keep the phone away from children. Please use the hands-free device (optional) when driving. Park the vehicle before using the handset. Switch off the phone when aboard an aircraft.
APPENDIX I : TROUBLESHOOTING TROUBLE POSSIBLE REASONS Unable to switch on your 1. phone Make sure the battery is charged. 2. Make sure the battery is installed properly Unable to charge battery 1. Make sure the charger is connected properly. 2. Make sure the battery is usable. The battery performance diminishes after several year’s use. 3. Is the battery overcharged? The handset comes into a slow charging mode after connected to the charger.
screen display for the name of your network supplier. 2. Is Call Barring enabled? 3. Have you paid your charges? 4. Have you activated the Fixed dialing function? 5. Have you enabled the “Restrict my phone number” rejected by the network? Unable to receive calls 1. Are you registered in the network? Check the screen display for the name of your network supplier. PIN locked 2. Have you paid your charges? 3. Is Call diverting enabled? 4.
APPENDIX II : ABBREVIATIONS AND EXPLANATIONS CUG Closed User Group GSM Global System for Mobile Communication GPRS General Pocket Radio Service SMS Short Message Service CB Cell Broadcast FDN Fixed Dialed Numbers SIM Subscriber Identity Module PIN Personal Identity Number. Supplied with SIM card. To unlock the SIM card. PIN2 Personal Identity Number 2. Supplied by the network provider. For special function in protected FDN supported by SIM. PUK Personal Unlock Key.
incoming call without interrupting the present call. It is different from multiparty calls. You can only talk to one party while another party is put on hold at the same time. Call Divert A service that allows you to divert an incoming call to a specified number. Normally calls are diverted if busy, no answer or not reachable. Divert all calls All incoming calls will be diverted by the network. If busy Divert your incoming calls while you are on another call.
SAFETY INFORMATION FOR WIRELESS HANDHELD PHONES Read This Information Before Using Your Handheld Portable Cellular Telephone. EXPOSURE TO RADIO FREQUENCY SIGNALS Your wireless handheld portable telephone is a low power radio transmitter and receiver. When it is ON, it receives and also sends out radio frequency (RF) signals. In August 1996, the Federal Communications Commissions (FCC) adopted RF exposure guidelines with safety levels for handheld wireless phones.
*; American National Standards Institute; National Council on Radiation Protection and Measurements; International Commission on Nonionizing Radiation Protection. ANTENNA CARE Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could damage the phone and may violate FCC regulations. PHONE OPERATION Normal Position: Hold the phone as you would any other telephone with the antenna pointed up and over your shoulder.
- Give full attention to driving. Driving safely is your first responsibility. - Use hands-free operation, if available. - Pull off the road and park before making or answering a call, if driving conditions require. ELECTRONIC DEVICES Most modern electronic equipment is shielded from RF energy. However, certain electronic equipment may not be shielded against the RF signals from your wireless phone.
Hearing Aids Some digital wireless phones may interfere with some hearing aids. In the event of such interference, you may want to consult your service provider (or call the customer service line to discuss alternatives). Other Medical Devices If you use any other personal medical device, consult the manufacturer of your device to determine if they are adequately shielded from external RF energy Your physician may be able to assist you in obtaining this information.
injury could result. Posted Facilities Turn your phone OFF where posted notices so require. OTHER SAFETY GUIDELINES Aircraft FCC Regulations prohibit using your phone while in the air. Switch OFF your phone before boarding an aircraft. Blasting Areas To avoid interfering with blasting operations, turn your phone OFF when in a “blasting area” or in areas posted: “Turn off two-way radio.” Obey all signs and instructions.
stations; below deck on boats; fuel or chemical transfer or storage facilities; vehicles using liquefied petroleum gas (such as propane or butane); areas where the air contains chemicals or particles, such as grain, dust, or metal powders; and any other area where you would normally be advised to turn off your vehicle’s engine. PRECAUTIONS AND WARNINGS Please read and understand all of the Precautions and Warnings contained in this manual before attempting to operate your phone. 1.
may result. 6. DO NOT short-circuit the battery terminals with metal items etc. 7. DO NOT use harsh chemicals, cleaning solvents or strong detergents to clean this phone. Always clean it with a soft, damp cloth. 8. DO NOT paint this phone. This can clog moving parts. OPERATING PROCEDURES Never violate any of the following Rules and Regulations of the FCC when using your phone. The following offenses are punishable by fine, imprisonment, or both: ! Using obscene, indecent, or profane language.
SAFETY INFORMATION FOR FCC RF EXPOSURE WARNING! Read this information before using your phone. CAUTION In August 1996, the Federal Communications Commission (FCC) of the United States with its action in Report and Order FCC 96-326 adopted an updated safety standard for human exposure to radio frequency electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies.
must be maintained between the user's body and the back of the phone, including the antenna, whether extended or retracted. Other belt-clips, holsters and similar accessories not used by this device may not comply with FCC RF exposure limits and should be avoided. Note: For more information about RF exposure, please visit the FCC website at www.fcc.gov. SAR Information THIS MODEL PHONE MEETS THE GOVERNMENT’S REQUIREMENTS FOR EXPOSURE TO RADIO WAVES. Your wireless phone is a radio transmitter and receiver.
with the phone transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output.
ID PP4TX-55C. Additional information on Specific Absorption Rates (SAR) can be found on the Cellular Telecommunications & Internet Association (CTIA) web-site at http://phonefacts.net. * In the United States and Canada, the SAR limit for mobile phones used by the public is 1.6 watts/kg (W/kg) averaged over one gram of tissue. The standard incorporates a substantial margin of safety to give additional protection for the public and to account for any variations in measurements. U.S.
biological effects may occur, but such findings have not been confirmed by additional research. In some cases, other researchers have had difficulty in reproducing those studies, or in determining the reasons for inconsistent results. 2. What is FDA’s role concerning the safety of wireless phones? Under the law, FDA does not review the safety of radiation-emitting consumer products such as wireless phones before they can be sold, as it does with new drugs or medical devices.
of RF safety to ensure coordinated efforts at the federal level. The following agencies belong to this working group: • National Institute for Occupational Safety and Health • Environmental Protection Agency • Federal Communications Commission • Occupational Safety and Health Administration • National Telecommunications and Information Administration The National Institutes of Health participates in some interagency working group activities, as well.
“PCS” phones. These types of wireless phones can expose the user to measurable radiofrequency energy (RF) because of the short distance between the phone and the user’s head. These RF exposures are limited by Federal Communications Commission safety guidelines that were developed with the advice of FDA and other federal health and safety agencies.
hours per day. These conditions are not similar to the conditions under which people use wireless phones, so we don’t know with certainty what the results of such studies mean for human health. Three large epidemiology studies have been published since December 2000. Between them, the studies investigated any possible association between the use of wireless phones and primary brain cancer, glioma, meningioma, or acoustic neuroma, tumors of the brain or salivary gland, leukemia, or other cancers.
interval between the time of exposure to a cancer-causing agent and the time tumors develop - if they do - may be many, many years. The interpretation of epidemiological studies is hampered by difficulties in measuring actual RF exposure during day-to-day use of wireless phones. Many factors affect this measurement, such as the angle at which the phone is held, or which model of phone is used. 6.
CTIA-funded research is conducted through contracts to independent investigators. The initial research will include both laboratory studies and studies of wireless phone users. The CRADA will also include a broad assessment of additional research needs in the context of the latest research developments around the world. 7.
Manufacturers of wireless phones must report the RF exposure level for each model of phone to the FCC. The FCC website (http://www.fcc.gov/oet/rfsafety) gives directions for locating the FCC identification number on your phone so you can find your phone’s RF exposure level in the online listing. 8.
9. What steps can I take to reduce my exposure to radiofrequency energy from my wireless phone? If there is a risk from these products—and at this point we do not know that there is—it is probably very small. But if you are concerned about avoiding even potential risks, you can take a few simple steps to minimize your exposure to radiofrequency energy (RF). Since time is a key factor in how much exposure a person receives, reducing the amount of time spent using a wireless phone will reduce RF exposure.
wireless phones, including children and teenagers. If you want to take steps to lower exposure to radiofrequency energy (RF), the measures described above would apply to children and teenagers using wireless phones. Reducing the time of wireless phone use and increasing the distance between the user and the RF source will reduce RF exposure. Some groups sponsored by other national governments have advised that children be discouraged from using wireless phones at all.
manufacturers to ensure that cardiac pacemakers and defibrillators are safe from wireless phone EMI. FDA has tested hearing aids for interference from handheld wireless phones and helped develop a voluntary standard sponsored by the Institute of Electrical and Electronic Engineers (IEEE).
! National Radiological Protection Board (UK): (http://www.nrpb.org.uk/) WARRANTY INFORMATION Protect Your Warranty Read your Warranty carefully, with the special consideration to paragraph seven of the Limited Warranty for your unit. “Warranty does not apply to... or to any product or part thereof which has suffered through alteration...mishandling, misuse, neglect or accident”.
UTSTARCOM COMMUNICATIONS CORP. 555 Wireless Blvd., Hauppauge, New York 11788, 800-229-1235 16808 Marquardt Avenue, Cerritos, California 90703, 562-802-5100 UTSTARCOM COMMUNICATIONS CANADA CO. 5155 Spectrum Way, Unit #5, Mississauga, Ontario Canada L4W 5A1, 800-465-9672 12 Month Limited Warranty UTSTARCOM COMMUNICATIONS CORP.
This Warranty does not apply to: (a) Product subjected to abnormal use or conditions, accident, mishandling, neglect, unauthorized alteration, misuse, improper installation or repair or improper storage; (b) Product whose mechanical serial number or electronic serial number has been removed, altered or defaced.
addition, for reference to an authorized Warranty station in your area, you can telephone in the United States (800) 229-1235, and in Canada (800) 465-9672 (in Ontario call 905-712-9299). THE EXTENT OF THE COMPANY’S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY’S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT.
limitation or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province. IN U.S.A.: UTSTARCOM Communications Corp. 555 Wireless Blvd. Hauppauge, NY 11788 (800) 229-1235 IN CANADA: UTSTARCOM Communications Canada Co.
