HB-711-OM-128-8270-Eng.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 2 TABLE OF CONTENTS Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 3 IMPORTANT SAFETY INSTRUCTIONS Please read all safety and operating instructions carefully before installation, and keep these instructions handy for future reference. Take special note of all warnings listed in these instructions and on the unit. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Water and Moisture: The unit should not be used near water. For example: near a bathtub, swimming pool, etc.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 4 INTRODUCTION Consider homebase your one-stop home message center and digital picture frame. The whole family can use homebase to communicate with one another and to keep each other in the know.
HB-711-OM-128-8270-Eng.
HB-711-OM-128-8270-Eng.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 7 INSTALLATION homebase Bracket Mounting Holes Wire Post(s) Power Adapter Wire Notch Refrigerator Door Front Surface DC Input Connector Refrigerator Door Seal DC Power Wire 1 inch Power Adapter Wire Notches Wire Cover homebase Adhesive Foam Pads Wire Cover Wall Mount Bracket Refrigerator Surface Installation 1.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 8 INSTALLATION (cont’d) Angle Bracket Mounting Holes homebase Unit DC Input Connector Wire Post(s) Power Adapter Wire Notches Bracket Upper Mounting Tabs Bracket Lower Mounting Tabs Angle Mount Brackets Countertop Installation 1. Find a suitable location on the countertop near an AC wall outlet. 2. Connect the power adapter plug to the DC input connector at the rear of the homebase. 3.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 9 INSTALLATION (cont’d) Flat-Head Self-Tapping Screw (2) Wall Surface Drill 1/4" Hole (2 Places) Mounting Hole Template Wall Bracket Mounting Tabs Wall Mount Bracket Plastic Wall Anchor (2) if Needed Wall Mount Installation Using the Wall Mount Bracket NOTE: To mount the homebase to a wall using the adhesive pads, follow the same instructions indicated earlier in “refrigerator surface installation” – page 7.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 10 INSTALLATION (cont’d) Plastic Wall Anchor (2) if Needed Drill 1/4” Hole (2 Places) Angle Mount Bracket Mounting Tabs Wall Surface Flat-Head Self-Tapping Screw (2) Angle Mount Bracket (2) Mounting Hole Template Wall Mount Installation Using the Angle Mount Brackets NOTE: It is not recommended that you use the foam adhesive pads when mounting the angle mount brackets to a wall surface; in this case, always use screws. 1.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 11 INSTALLATION (cont’d) Internal Battery Activation and/or Replacement A type CR2032 battery is installed in a compartment behind the front panel of the homebase. If the unit is being used for the first time, the battery must be activated. A plastic insulator prevents contact with the battery terminals. The insulator must be removed for the calendar/clock backup functions to operate.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 12 CONTROLS, INDICATORS AND CONNECTORS 1 5 2 6 3 7 4 8 9 13 smil 10 14 11 12 15 1. Power On/Off Switch 2. USB Connector 3. SD/MMC/MS/xD Connector 4. CF Connector 5. Up ( ) Navigation Button 6. OK / MENU Button 7. Down ( ) Navigation Button 8. MEMO Button 12 9. 10. 11. 12. LCD Display LED Indicator Memo Writing Surface Microphone, Camera, Light Sensor 13. Speakers 14. - Volume + Control 15.
HB-711-OM-128-8270-Eng.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 14 OPERATING THE HOMEBASE Preliminary Connections Prior to initial operation, the unit must be plugged in, and the tab (“REMOVE THIS TAB”) on the right side of the unit must be removed to enable backup battery operation. Connecting the power Power to the homebase is provided by the AC-to-DC wall adapter, which delivers +9VDC to the DC input connector at the rear of the unit.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 15 GETTING STARTED Once homebase is properly mounted and plugged in, you are ready to begin. If you want to use your own pictures, be sure to have your memory card already connected. 1. Turn homebase on by moving the power switch on the left side upward. After just a few seconds, you will see a white welcome screen that says “audiovox homebase.” IF YOUR MEMORY CARD IS CONNECTED… a slide show with your pictures will automatically start.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 16 FAMILY NAMES Your Homebase can be customized for your family by inputting you family member names into the unit. This will allow you to leave video and voice memos for specific family members. If there is a message waiting for someone, their name(s) will appear on the screen indicating they have a memo. How do I input family names? 1. Press the OK/menu button. Highlight “settings” and press OK/menu. 2. Highlight “family names” and press OK/menu.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 17 MEMOS How do I leave a video memo? 1. Press the orange button that says memo. (This button will take you straight to the “memo” menu no matter where you are.) You can also press the menu button then highlight “memo” and press OK/menu. It’s up to you. 2. The “memo” menu has 5 options: “exit”, “record video”, “record voice”, “play/erase” and “erase all”. exit record video record voice play/erase erase/all 3.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 18 MEMOS (cont’d) Now, what would you like to do? To save your video memo… Highlight “keep/exit” and then press OK/menu. Your memo is saved. The orange light in front will stay lit and homebase will go back home. NOTE: If one of the clock display options is active you will also see “memo(s) for:” followed by the family members name displayed on the screen. Thursday - Jan.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 19 MEMOS (cont’d) How do I leave a voice memo? 1. Press the orange button that says memo. (This button will take you straight to the “memo” menu no matter where you are.) You can also press the menu button then highlight “memo” and press OK/menu. It’s up to you. 2. The “memo” menu has 5 options: “exit”, “record video”, record voice “play/erase” and “erase all”. 3. Highlight “record voice ” and then press OK/menu. The “record voice > for” will appear.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 20 MEMOS (cont’d) How do I listen to a voice or view a video memo? 1. Press memo. 2. Highlight “play/erase” and press OK/menu. All saved voice memos will pop up with dates and times. Unheard memos are left in orange. 3. Highlight the memo you want to hear and press OK/menu. As you highlight the memo an icon will appear to the right of the memo indicating what type of memo it is.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 21 MEMOS (cont’d) Now, what do you want to do? “play” – will play your memo again and return you to this menu. “erase” – will erase your memo again and return you to this menu. “keep” – will save your memo and change the color to gray indicating that it has already been heard. “keep as new” – will save your memo and change the memo name color to orange as if it has not been heard. 5. When finished, highlight “exit” and press OK/menu to go back home.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 22 MEMOS (cont’d) How do I listen to a voice or video memo, but not delete it? 1. 2. 3. 4. 5. 6. 7. Press memo. Highlight “play/erase” and press OK/menu. Highlight the memo you want to hear and press OK/menu. Highlight “play” and press OK/menu. Listen to or view the memo. When memo is finished, highlight “keep” and press OK/menu. Highlight “exit” and press OK/menu to go back home. How do I erase all voice and video memos? 1. Press memo. 2.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 23 CALENDAR How do I leave a voice or video memo for a specific date? NOTE: Dated voice memos are automatically deleted 72 hours after scheduled date. 1. Press the OK/menu button. You will see the main “menu” (“exit”, “memo”, “calendar”, “timer”, “photo” and “settings”). “Calendar” will automatically be highlighted in orange. 2. Press OK/menu. 3. In “Calendar”, press the up or down arrows to change dates.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 24 CALENDAR (cont’d) Now, what would you like to do? To save your voice or video memo… Highlight “keep/exit” and then press OK/menu. Your memo is saved. The orange light in front will stay lit and homebase will go back home. Be sure to use the marker to write down to whom the memo is intended for on the marker board under the “memo for:” light. To listen to your voice or video memo… Highlight “review” and press OK/menu. Listen to your memo again.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 25 CALENDAR (cont’d) Now, what would you like to do? To erase a voice or video memo… a. Highlight “erase” and press OK/menu. Screen will automatically return to calendar memo screen and memo will be gone from list. b. Highlight “exit” and press OK/menu. Screen will return to calendar. c. Press OK/menu and screen will return to calendar memo screen. d. Highlight “exit” and press OK/menu to go back home. To keep a voice or video memo… a.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 26 CALENDAR (cont’d) Now, what do you want to do? To make this a one-time event… a. Leave “on” highlighted and press OK/menu. Screen will automatically return to event selection screen. A small orange box will appear on the date to indicate that your message has been saved for that date. b. Highlight “back” and press OK/menu. Screen will return to the calendar screen. c. Press OK/menu and highlight “exit” and press OK/menu again to go back home.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 27 CALENDAR (cont’d) How do I erase a calendar event? 1. 2. 3. 4. 5. 6. Press the OK/menu. Press OK/menu again. Select day and month in “calendar”. Highlight the desired date and press OK/menu. Highlight “event memos” and press OK/menu. Highlight the event and press OK/menu and highlight “erase”; press OK/menu again. Screen will return to calendar memo screen and event will be missing. 7. Highlight “back” and press OK/menu. Screen will return to calendar.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 28 COUNTDOWN TIMER How do I set a countdown reminder? 1. Press OK/menu and the main “menu” will pop up. exit memo calendar timer photo settings 2. Highlight “timer” and press OK/menu. A split screen display appears with the countdown timer on the left and a slide show on the right. countdown timer 00:10:00 h m s 3. When the timer display appears, the hour (h) digits are flashing and “10 minutes” is indicated. 4.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 29 PHOTO MENU The homebase can accept 6 different types of memory devices SD, MMC, MS, xD and CF cards as well as a USB flash drive. When you plug one of these devices into the appropriate receptacle the unit will go directly to step 6 below and display the photo icons on your memory device.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 30 PHOTO MENU (cont’d) 6. All photos will automatically be displayed as thumbnails on the screen. Highlight the photo you would like to copy by pressing the up and down arrows; when photo is selected, press OK/menu. exit back copy next copy all 7. The photo will be displayed enlarged, followed by a menu that will automatically pop up with 5 options. Now, what do you want to do? To copy this photo to your photo library… Highlight “copy” and press OK/menu.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 31 PHOTO MENU (cont’d) What can I do with my photos once they are in the Photo Library? 1. Press OK/menu and the main “menu” will pop up. 2. Highlight “photo” and press OK/menu. 3. Highlight “photo library” and press OK/menu. All photos stored in the photo library will automatically pop up. 4. Highlight desired photo by pressing the up and down arrows; when photo is selected, press OK/menu. 5.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 32 PHOTO MENU (cont’d) Now, what would you like to do? To make this picture the only picture displayed… Highlight “single slide show” and press OK/menu. Confirm that “on” is highlighted and press OK/menu once more. Now that photo you selected will be displayed until you change back to the slideshow. NOTE: Turning single slide show on will stop home screen slide show. To restore, repeat above directions, but select “off” instead.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 33 GENERAL SETTINGS (cont’d) How can I change the way the slide show plays? 1. Press OK/menu and the main “menu” will pop up. 2. Highlight “photo” and press OK/menu. 3. Highlight “slide show” and press OK/menu; a menu will automatically pop up giving you 4 options. Now, what do you want to do? To enable the slide show… Highlight “enable slide show” and press OK/menu. Highlight “on” and press OK/menu.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 34 GENERAL SETTINGS How can I choose between normal or widescreen for my photos? 1. Press OK/menu and the main “menu” will pop up. 2. Highlight “settings” and press OK/menu. 3. Highlight “general setup” and press OK/menu. exit general setup time/date setup alarm clock display family names 4. Highlight “photo mode” and press OK/menu. 5. Highlight “normal” or “widescreen” and press OK/menu. After selection, the unit will go back home.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 35 GENERAL SETTINGS (cont’d) How can I clear all data stored in memory? NOTE: This will permanently delete ALL stored photos, voice and video memos, events, times and alarms. 1. Press OK/menu and the main “menu” will pop up. 2. Highlight “settings” and press OK/menu. 3. Highlight “general setup” and press OK/menu. 4. Highlight “clear memory” and press OK/menu. 5. Homebase will clear all data and restart.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 36 GENERAL SETTINGS (cont’d) 7. Repeat to select the numerical day of the month, and press OK/menu. Note: When this is done correctly, the clock will automatically select the proper day name for the date entered. 8. The year is now flashing. Use the up and down arrows to select the proper year, and then press OK/menu. 9. Time and date setup is now complete, and the screen will return to the “settings” menu automatically. 10.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 37 GENERAL SETTINGS (cont’d) Now, what do you want to do? To turn alarm on… exit exit on alarm on/off alarm on/off on every day alarm set alarm set off 1. Highlight “alarm on/off” and press OK/menu. 2 You can now set an alarm for today only by highlighting “on” and pressing OK/menu or you can set the alarm to activate everyday at this time by highlighting “on everyday” and pressing OK/menu. To turn alarm off… 1.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 38 GENERAL SETTINGS (cont’d) How do I change where the time is displayed? 1. Press OK/menu and the main “menu” pops up. 2. Highlight “settings” and press OK/menu. 3. Highlight “clock display” and press OK/menu. exit general setup time/date setup alarm clock display family names Wednesday - Dec.. 17th 17th,, 2008 4. Highlight desired position from list (“off”, “screen bottom edge”, “large centered” and “split screen”), and then press OK/menu.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 39 GENERAL SETTINGS (cont’d) How do I select my language? 1. 2. 3. 4. 5. 6. Press OK/menu and the main “menu” pops up. Highlight “settings” and press OK/menu. Highlight “general setup” and press OK/menu. Highlight “language select” and press OK/menu. Highlight “english” or “french” and press OK/menu.
HB-711-OM-128-8270-Eng.
HB-711-OM-128-8270-Eng.
HB-711-OM-128-8270-Eng.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 43 90 DAY LIMITED WARRANTY Applies to Audiovox Video Products AUDIOVOX ELECTRONICS CORP.
HB-711-OM-128-8270-Eng.qxp 6/5/08 9:37 AM Page 44 Audiovox Electronics Corp.
