HOME THEATER SYSTEM INSTRUCTION MANUAL Please read the instruction manual carefully before using your unit.
GENERAL Table Of Contents Introduction Introduction Thank you for purchasing this production. For best performance, please read this manual carefully. It will guide you in operating your product. Supplied Accessories Maintenance Placement IMPORTANT SAFETY INSTRUCTIONS ...........1 Manufactured under license from Dolby Laboratories.‘Dolby’,‘Dolby Digital’,‘Pro Logic’ are trademarks of and the double -D symbol Dolby Laboratories. FUNCTION CONTROL .......................................
IMPORTANT SAFETY INSTRUCTIONS The lightning flash with an arrowhead symbol, within the equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to cause an electric shock. WARNING The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in this owner manual.
FUNCTION CONTROL Front Panel 11 12 13 14 1 2 3 4 5 6 1. POWER button Turn the power on or off. 2. AV3 AUDIO IN (L&R) jacks Connect to audio outputs. 3. AV3 VIDEO IN jack Connect to video outputs. 4. AV1/2/3 buttons Press AV1 or AV2 to enter auto-detected/autoswitching mode, press again to switch to “forced analog mode”. Press AV3 button to select the AV3 input. 5. TUNER / BAND button Select the radio mode and press again to select between FM and AM band. 6.
FUNCTION CONTROL (Continued) Remote Control 1 POWER FUNCTION 7 8 2 BAND NEXT DISP LAY 3 4 MEM O RY PREV 5 / MONO EO STER TEST 9 10 11 12 13 14 6 1. POWER button Turn the unit on from standby mode or turn the unit into standby mode. 2. BAND button Switch the radio band between FM and AM. 3. TUNING button Search a radio station. 4. MEMORY button Memorize a radio station. 5. SURROUND button Change the output channels or the output sound mode in AV IN mode. 6.
SETUP Power Connection CAUTION: • Before making connection, check that the rated voltage of your unit matches your local voltage. • Keep your hands dry when you are connecting the power cord to the wall outlet in case of electric shock. • When you are not going to use the unit for a long period of time, disconnect the power cord. Connecting The Speakers & Subwoofer 1. The speaker cords have been color-cord to simplify connection.
SETUP (Continued) Positioning The Speakers & Subwoofer CENTER Place on the top of or below the TV. FRONT SPEAKERS Place both sides of the TV, equal distances apart. SUBWOOFER Can be placed anywhere. REAR SPEAKERS Place right beside or slightly behind your listening position, and a little higher than your ears.
SETUP (Continued) Connecting The Radio Antenna FM: Connect the FM antenna (included) to the FM ANTENNA terminals. Fully unwind the wire antenna. Then extend the wire antenna and place it in the position that sounds best. AM: Connect the loop antenna (included) to the AM LOOP ANTENNA jack. Rotate the antenna to get the best receiving position. Video & Audio Input/Output Setting AV1 (SAT/VCR) Connect the audio and video output jacks of the AV equipment (VCR, Satellite receiver, etc.
SETUP (Continued) Video & Audio Input/Output Setting(Continued) AV3 To play with a portable AV equipment (Video game console, etc.), use the AV3 on the front panel of the unit. Connect the audio and video following the instructions of AV1 and AV2.
SOUND ADJUSTMENT To Adjust The Channel Level Use the remote control to make the following changes to speaker balance. Press the SOUND button to select the desired speaker and press NEXT or PREV button to adjust the channel level. Notes : 1. If you do not press any button within a few seconds, the display will return to normal. 2.
RADIO OPERATION Tuning Into A Station Manually 1. Press the TUNER/BAND button on the unit or the FUNCTION button on the remote control until the frequency band appears on the display. 2. Press the TUNER/BAND button again or the BAND button on the remote control to select the desired band. 3. Press the TUNING +/- buttons to tune into a station. FM Stereo Press the MONO/STEREO button on the remote control until “STEREO” appears on the display.
TROUBLE SHOOTING GUIDE The following checks will assist in the correction of most problems which you may encounter with your system. SYMPTOM CAUSE (AND REMEDY) No Power. • Check that the AC power cord is connected. No sound. • Rotate the VOLUME clockwise to increase volume. • Select the correct AV input and the correct input mode (Digital or analogy sound). No sound from one channel or unbalanced left and right volume. • Check the speaker connections of the inoperative channel.
