Owner's Manual
Table Of Contents
- Owner's Guide
- Installation and Reference Guide
- Table of Contents
- Before You Begin
- Wire Connection Guide
- Additional Ports
- Set Up & Programming
- Transmitter Programming - Feature Bank 1
- Manual Feature Programming - Feature Bank 2 & 3
- Manual Feature Programming - Feature Bank 4 & 5 - N/A
- Shock Sensor Programming, Adjustment and Testing - Feature Bank 6
- Code Alarm Utility App Feature Programming / Firmware Updates (optional)
- Dome Light Delay / Theater Dimming
- Chirp Delete - User Accessible
- User Selectable LED
- Feature Descriptions
- Transmitter Button Functions
- Security Trigger Zones
- Security and Keyless Entry Installation Quick ReferenceGuide
Set Up & Programming
Transmitter Programming - Feature Bank 1
1.
2.
3.
Turn the ignition ON.
Press and hold the valet/override button.
Within 10 seconds the system will chirp (3) three times.
4. Press 1 button
of
each transmitter you wish to program.
5. The system will respond with 1 chirp for each accepted transmitter.
6. Pressing the override button at anytime during programming will advance to
the next bank.
NOTE:
The
system will exit transmitter programming after
15
seconds of inactivity.
NOTE: This system has 1 button programming which programs all channels
of
the
system.
NOTE: The system will hold up to 4 transmitters
in
memory, programming a 5th
transmitter will erase the oldest transmitter
in
memory.
NOTE: This system has PTN - Programmed Transmitter Notification. Each time the
ignition is turned ON , the LED will flash the number
of
transmitters programmed to the
system.
Manual Feature Programming - Feature Bank 2 - 5
1.
2.
3.
4.
5.
6.
Turn the ignition ON.
Press and hold the valet/override button.
Within 10 seconds the system will chirp (3) three times.
Use the valet/override button to advance through each option bank. For
feature programming advance to Feature Bank
2,
or
3,
which is (4)
four, and (5) five chirps.
Use the transmitter
<::J
button to scroll through the selections
in
each
feature bank, the system will chirp to match the feature number.
Press the transmitter @ button to change the desired feature. The LED will
flash indicating the changed feature.
Defaulting All Features: Pressing the
riJ
button anytime while
in
any
of
the feature
banks will default all features and return
you
to feature bank 2 - 4 chirps.
NOTE: The system will remain
in
feature programming mode as long as the ignition is
on, there is no time limit.
To
exit programming turn the IGNITION OFF.
Shock Sensor Adjustment - Feature Bank 6
1.
2.
3.
4.
5.
6.
7.
Turn the ignition ON .
Press and hold the valet/override button.
Within 10 seconds the system will chirp (3) three times.
Use the valet/override button to advance through each option bank. For Shock
Sensor Adjustment advance to Feature Bank 6, which is (8) eight chirps.
Turn the ignition OFF, exit the vehicle and close all doors.
Select Auto-Learning
or
Manual Adjustment:
Option (a) Auto-Learning
Press and hold the transmitter tJ button until the system emits 2
long chirps to enter Shock Sensor Auto-Learning Mode.
Strike the vehicle to set the level intended for the system to trigger.
The system will store the setting, chirp 1 time and automatically
advance to step 7, Manual Adjustment and Testing.
Option (b) Manual Adjustment
Press and hold the transmitter
c:i
>
))
button until the system emits 1
long chirp to advance to step 7, Manual Adjustment and Testing.
Manual Adjustment and Testing. Adjustment and testing can be performed at
any time during this step. During testing 3 short chirps indicates warn-away, 1
long chirp indicates full trigger. Allow 3 sec. between each adjustment / test.
a.
Full trigger - Press the transmitter @ button to increase
sensitivity. Press the
riJ
button to decrease sensitivity.
b. Warn-Away - Press the
c:i
>
))
button to increase sensitivity. Press
the tJ button to decrease sensitivity.
8.
Programming will exit by turning the ignition ON
or
if there is no activity for 60
seconds. The system will flash the parking lights 3 times to confirm exit.
Note: Sensitivity ranges from O
(off)-
27 (most sensitive), the default setting is 4.
The system will chirp when sensitivity is raised
or
lowered with 2 chirps indicating the
highest or lowest setting.
Defaulting the Shock Sensor: Enter Feature Bank 6, step 6 and press and hold the
fiJ
button for 3 seconds, the system will emit 1 long chirp to confirm reset and will
return to step
6.
Continue with step 6
or
exit programming.
Chirp Delete - User Accessible
System ARM/DISARM chirps can be toggled ON
or
OFF without entering the
programming feature banks.
1.
Turn the ignition ON then OFF.
2.
Press and release the valet/programming button 3 times. The system
will respond with 1 chirp for ON
or
2 chirps for OFF.
User Selectable LED
This feature will control whether the LED is ON
or
OFF when the system is Armed/
Locked. This will be selectable
in
feature programming
OR
on-the-fly without entering
the programming feature banks.
1. Turn the ignition ON , OFF, ON , OFF.
2. Press and release the valet/programming button 3 times. The system
will respond with 1 chirp for ON
or
2 chirps for OFF.
PC
Based Feature Programming/ Firmware Updates
When using the NEW Code Alarm Utility App along with a VEPROG Programming tool you may program selectable features
or
update the firmware
of
this module.
1.
To
download the Code Alarm Utility App visit the Voxx University website at voxxuniversity.com.
2. Select VOXXTECH and locate the utility app under the heading Software Downloads.
Technical Support (800) 421-3209
or
visit
www.voxxuniversity.com
R410-193-140