RUDIOUOX universal power windows MOUNTING INSTRUCTIONS DETAILED INSTRUCTIONS FOR MOUNTING POWER WINDOWS ON THE U.S.
□’ REMOVE HANDLE FROM WINDOW REGULATOR/PIVOT g—— APPLY CENTERING ADHESIVE TO THE PANEL Place adhesive over pivot making sure that it adheres properly to door casing PANEL DEMOUNTING Remove door pane!. f.
B . MANUALLY CHECK THE MOVEMENT OF THE WINDOW nw Adjust the registers or guides if the window does not operate freely 0 OPTIONAL OPERATION: A • IN ORDER TO USE THE SM ALLEST CAP ON SOM E VEHICLES, IT M AY BE NECESSARY TO M OVE BACK THE W INDOW REGULATOR ASSEM BLY. B - AFTER REM OVING ORIGINAL BOLTS FROM THEIR SEATS, REFER TO THE TABLE BELOW TO CHOOSE SUITABLE SPACERS AND BOLTS (SUPPLIED IN KIT NO. 2). KIT NO. 2 Trapezoidal spacers h. 5/16" Bolts h. 3/8” Trapezoidal spacers h. 3/16” Bolts h.
C • INSERT SPACERS BETW EEN M ANUAL M ECHANISM AND DOOR-PANEL Check that the bolts of the window assembly are tight 0 FIT ADAPTOR ON REGULATOR PIVOT iÉÉJtâÂ. STWTfn From Kit No. 3, choose the correct adaptor for the model of vehicle. See adaptor Table below. Adaptor table (Kit No. 3) N. 1 ALFA ROMEO - AUTOBIANCHI - BEDFORD - DAF DATSUN - FIAT - LANCIA - MERCEDES - NISSAN OPEL - PORSCHE - SUBARU N. 2 ARO - CITROËN - PEUGEOT - RENAULT - SEAT TALBOT N.
Take caution in removing adaptor from Kit. Do not twist-off, If the handle is fixed with a screw, use it to fix the adaptor 0 INSERT GEAR SLEEVE INTO THE TRANSMISSION KIT NO. 4 Geared sleeve to be inserted towards inside of vehicle A) Insertion from the red marked side. B) Insertion from the opposite side of the red mark. Gear conversion A) Wrong: too long. B) Wrong: too short. C) Right: length of geared sleeve and pivot are the same.
0 SECURE GEAR TO THE TRANSMISSION WITH CIRCLIP KIT NO. 1 ' Tb^V '© (Circlip included in KIT No 0" INSTALLATION OF THE ELECTRIC POWER WINDOW MECHANISM INTO THE DOOR Fixing or shifting of transmission bracket. KIT NO. 5 It is possible to mount one or more brackets in pos.
Motor may be rotated on transmission in order to faciiitate a secure mount © A A) Remove the screws. Rotate the geared motor to the required position C) Retighten the screws in their seats. FASTENING OF GEARED MOTOR Drill door panel to hook*up springs. IMPORTANT: The power cable for the motor must always be positioned downwards Fastening of geared motor with brackets A) Fastening with two brackets, 6) Fastening with brackets and springs. C) Fasten geared motor behind door panel with one bracket.
Fastening of geared motor with springs Take springs and wire clip out of KIT No 1 1) Spring, 2) Wire c!ip- Hook up springs and lock hooks a APPLY PADDING TO THE GEARED MOTOR IN CASE THE MOTOR, OR PARTS OP IT, ARE IN DIRECT CONTACT WITH ANY METAL PARTS, THE SUPPLIED PADDING SHOULD BE USED AS SHOWN BELOW.
POSITION AND FIX BRACKET Position the bracket without forcing the transmission Fasten bracket through one of the holes (Use the outer ones, where possible). 1) Internal metal bushing 2) External rubber bushing Drill 7/64” holes to fasten bracket 1) Screw 2) Speed nut.
LOCK ADAPTOR AND GEAR SLEEVE Insert the screw in the space between the adaptor and the gear sleeve CUT DOOR PANEL WITH SPECIAL CUTTER DOOR PANEL CUTTER TOOL SUPPLIED UPON REQUEST 0 m m ] Center the cutter with the adhesive Tighten with a wrench until the cutter comes free Remove any remaining adhesive.
FIX GROMMET WITH RETAINER RING |g Mo, 1 No. 3 NO. 3 No. 1 Smalt, No. 2 Medium No, 3 Larg The grommet cap locks to panel by means of a retainer ring The grommet has to come through the door casing at least 5/32 in order to be locked with the retainer ring. To choose the proper grommet cap. follow this procedure: — Insert grommet cap no. 1 (SMALL) into the panel, if it does not come through, try no P (MEDIUM) and then, if necessary, no. 3 (LARGE) ’ NO. 1 NO 1 10 MAJC 5/32" Na. 1 V»! A) No.
UNIVERSAL ELECTRIC WINDOWS WITHOUT CLUTCH ART.5S000013 0 FIT CAP ON DOOR PANEL Fii Ihe Cap on the grommel and fit the panel on the door NOTE! tB A %^ Ho. & ^ n __Q_ ^n L0_ When the regulator pivot does not come out from the pane! (photo A and B) you can use cap No. 0 tor a better appearance.
INSTALLATION EXAMPLE FOR ELECTRIC POWER WINDOWS * \ IN SOME CARS IN THE U.S. BUICK CENTURY (4 Doors) front iefl BUICK CENTURY (4 Doors} rear righi — in&sri gaar H 15 (insert trcjm red marked side) — aclapter Me. 9 — turn tranernission aids of geared motor towards inside of car ” adjust bracket on transmission shortened 1“ — Ir^&erl gear H 16 finsert from red marked side) — adapter No. 9 — affix geared motor wilh springs — grommet No, T — cap No.
FORD TEMPO front right HONDA ACCORD front right — — — — — — — — — — — — — — — — — * adjust bracket on transmission rotate geared motor 180° on transmission insert gear H 15 (insert from red marked side) adaptor No. 12 apply paddings to geared motor turn transmission side of geared motor towards inside of car affix geared motor with bracket shortened 2.2” grommet No. 1 cap No. 1 * adjust bracket on transmission insert gear H 15 (insert from red marked side) adaptor No.
MAZDA 626 4 Doors (U.S.) mod. ’89 rear nghi PONTIAC 6000 from right —> adjust bracket on transmission and bend appropriately — insert gear H 15 (insert from red marked side) — adaptor No. to — apply paddings to geared motor — turn transmission side o( geared motor towards inside ott car — affix geared motor vnth bracket shortened i " — grommet No. t — cap No.
CHEVnOLET/QMC S-10/15 PJCKUP rront left DODQE CARAVAN front left — shorlftn bratkQi on trarsmisBioo 1.6" — gaor H 15 (insart from rad marked side) — edaplor No. B — — — — shorten bracket on iransmiaaion 1.6" rpiBla geared motor 9D* on transmisaion Inesrt gear H 1S flnsari from rod marked side) adaptor No. 13 — — — — lorn trarsmiaslon side of geared motor towards inside of oar etfia geared motor with two brackata shodened 2.2" grommet No 1 oap No.
ISU2U PICKUP front left — rotate geared motor 90* on transmission — Insert gear H 15 (insert from c^posito side ot red marked side) ^ adaptor No. i — apply paddings to geared motoc — turn grill side of geared motor towards inside ol cat — affix geared motor with bracket — grommet No. i — cap No.
ELECTRICAL WIRING DIAGRAMS Listed here are wiring diagrams of typical installations for the Electric window kits using the wiring kits. NOTE! For safety reasons it is necessary that the power supply to the windows be con nected to the appropriate terminal of the ignition side of the ignition relay block. It is recommended that onty wiring kits be used. Whenever this is not possi ble, proper wiring of at least 16 AWG must be used with the suitable in-line fuse.
□* ~ ELECTRICAL CIRCUIT: 3 SWITCH WITH 6 CONTACTS AND SEPARATE LIGHT * Use original wiring. Art 33020010 complete with 25 Amp, fuse.
ga£iZKl$3L^' ZI
