Installation manual

ManualsBrandsAudiovox ManualsAutomotiveAPS-596C

128-8804b

1 of 16

Page 1

Model APS-596C

Installation Manual

Remote Control Vehicle

Security System

Rev B: New Format

PATENTED: www.voxxintl.com/company/patents

Table Of Contents:

Before You Begin Page 2

Wire Harnesses Quick View Page 3

Mounting Of The Major Components Page 4

8 Pin Power Harness Wiring Page 5 - 6

Wiring the 11 Pin Accessory Input/Output Connector Page 6 - 7

4 Pin White Connector Shock Sensor Harness Page 8

2 Pin LED / Valet Connectors Page 8

3 Pin Door Lock/Unlock Connector & Wiring Page 8 - 10

4 Pin Upgrade Telematic Module Page 10

Completing The Installation Page 10

Dome Delay Learning Proceedure Page 10

Adjusting The Shock Sensor Page 10 - 11

Final Steps Wire Dressing and Operation Explanation Page 11

DBI Port Information Page 11

Programming Transmitters Page 12

Programming Alarm Feature Bank 2 Page 12

Selectable Features Page 13

Circuit Wiring Layout Page 14

Notes Page 15-16

Summary of content (16 pages)

PAGE 1
Model APS-596C Installation Manual Remote Control Vehicle Security System Table Of Contents: Before You Begin Wire Harnesses Quick View Mounting Of The Major Components 8 Pin Power Harness Wiring Wiring the 11 Pin Accessory Input/Output Connector 4 Pin White Connector Shock Sensor Harness 2 Pin LED / Valet Connectors 3 Pin Door Lock/Unlock Connector & Wiring 4 Pin Upgrade Telematic Module Completing The Installation Dome Delay Learning Proceedure Adjusting The Shock Sensor Final Steps Wire Dressing and Ope
PAGE 2
Before You Begin PROFESSIONAL INSTALLATION IS STRONGLY RECOMMENDED Roll down window to avoid locking the keys in the vehicle during installation. Avoid mounting components or routing wires near hot surfaces or near moving parts like the steering wheel as it may prevent proper operation of the vehicle. Tape or loom wires under the hood and dash for protection as well appearance. Use grommets when routing wiresthrough metal surfaces to prevent chafing and shorting.
PAGE 3
11 Pin Main Wiring Harness 1 Green / Black 2 Blue / Black 3 Black / White 4 Orange / White 5 6 7 8 9 10 11 Part # 1122916 Channel 4 Output (-) 300mA Alternate Channel 3 Output (-) 300mA Horn Output (-) 300mA Gnd. Output When Disarmed (-) 300mA Dark Green Brown Purple Negative Hood / Trunk Trigger Input Neg. Door Trigger Input Pos. Door Trigger Input Yellow White / Blue Lt. Green Ignition Input Switched +12 Volts Programmable Headlight Out (-) 300mA Add. Neg. Trigger Input Lt.
PAGE 4
MOUNTING OF THE MAJOR COMPONENTS Control Module: Part # 1365043 Select a mounting location inside the passenger compartment ( up behind the dash ), and secure using the two screws provided. The control module can also be secured in place using cable ties. Do Not mount the control module in the engine compartment, as it is not waterproof. You should also avoid mounting the unit directly onto factory installed electronic components.
PAGE 5
WIRING THE SYSTEM Large 8 Pin Power Connector: Red/White (5 Amp) & Red Fused (15 Amp) Wires : + 12 VDC Constant Battery Source This wire controls the sensitivity of the voltage sensing circuit, which detects the turning on of an interior light when a door is opened. It will also detect the switching on of parking or headlamps and in many cases will trigger the alarm when a thermostatically controlled electronic radiator cooling fan switches on.
PAGE 6
Black Wire: Chassis Ground Connect this wire to a solid, metal part of the vehicle’s chassis. Do not confuse this wire with the thin black antenna wire that exits the control module independently. White Wire: + 12 VDC Pulsed Parking Light Output (15 Amp Max) This wire is provided to flash the vehicle’s parking lights. Connect the white wire to the positive side of one of the vehicle’s parking lights.
PAGE 7
Dark Green Wire: ( - ) Instant Trigger Zone This is an instant on ground trigger wire. It must be connected to the optional previously installed hood and trunk pin switches when used. Brown Wire: - Door Trigger If the vehicle’s courtesy light switches have a ( - ) ground output when the door is opened (GM and most Imports), you must connect this wire to the negative output from one of the door switches. WARNING: Do not use the brown wire if the vehicle has + 12 volt output type door switches.
PAGE 8
WARNING: Connecting the light blue/green to the high current switched output of trunk release circuits, some remote start trigger inputs, will damage the control module. Connect the light blue/green to terminal 86 of a 30 A automotive relay, connect terminal 85 to a + 12 volt source, and wire the remaining relay contacts to perform the selected function of channel 5. 2 Pin White Connector: DASH MOUNTED LED.
PAGE 9
Connect the door side of the cut wire to terminal 30 of the optional relay added. Connect the vehicle side of the cut wire to terminal 87a of the optional relay added. Connect the green wire of the 3 pin harness to terminal 86 of the optional relay added. Connect terminal 85 of the optional relay added to a fused constant + 12 volt source.
PAGE 10
Resistive Circuits, As Well As 4 Wire Polarity Reversal and 5 Wire Alternating 12 Volt Door Lock Control Circuits These applications require the use of additional components which may include relays, fixed resistors, or for convenience, the AS 9159a Door Lock Interface. Refer to the AUDIOVOX Door Lock Wiring Supplement and or the Audiovox fax back service for information on your particular vehicle for properly connecting to these types of circuits.
PAGE 11
4 PIN IN VEHICLE DATA BUS PORT (DBI Port) (Connector Port) The 4 pin port located on the side of this module is for proprietary Audiovox data bus interface modules. These modules are used to access a variety of features in the vehicle which can be as simple as door trigger inputs, to more complex door locks outputs, or transponder interfaces for remote starting. DO NOT connect anything to this port other than the Audiovox DBI modules or damage to the Remote Start module will occur.
PAGE 12
The transmitters are pre-programmed from the factory. If you find you need to program new or additional transmitters follow the instructions below. PROGRAMMING BANK 1 (TRANSMITTERS): 1) Turn the ignition key to the on position. 2) Press and release the valet/programming switch 3 times (Siren Chirps). 3 Press the Lock Button of each transmitter you want programmed until you hear a chirp from the horn or siren. 4) Turn the ignition switch off.
PAGE 13
Page 13 128-8804b 13 of 16 1 Chirp 1 Sec. Auto Lock On Auto UL Dr. On Arm Passive Passive Arm Siren/Horn 10mS Custom Code On On Voltage Sense Not Available Not Available Pulse Not Available Not Available Not Available Push & Hold 2 Chirps 3.5 Sec. Auto Lock Off Auto UL All On Disarm Active Active Arm Siren Only 16mS Valet Off Off Hardwire 40mS Horn Only 30mS Siren chirps 2 times indicating access to RF feature program mode.
PAGE 14
For technical support go to www.prestigecarsecurity.com or call 1 800 225 6074. © 2013 Audiovox Electronics Corp., Hauppauge, N.Y.
PAGE 15
NOTES Page 15 128-8804b 15 of 16
PAGE 16
NOTES Page 16 128-8804b 16 of 16