OWNER'S MANUAL AV-415 AM/FM/MPX RADIO WITH FOLD-DOWN DETACHABLE FRONT PANEL, AUDIO CASSETTE PLAYER, CD CHANGER CONTROLS AND QUARTZ CLOCK
INST ALL AT ION INSTRUC INSTALL ALLA INSTRUCTT IONS INSTALLATION INSTRUCTIONS This unit is designed for installation in cars, trucks, and vans with an existing radio opening. In many cases, a special installation kit will be required to mount the radio to the dashboard. These kits are available at electronics supply stores and car stereo specialist shops. Always check the kit application before purchasing to make sure the kit works with your vehicle.
DAY MON. - FRI.
RADIO WIRING R A DIO WIRING REFER TO PAGE 4 FOR SPEAKER WIRING ANTENNA AUTOMATIC ANTENNA CAR FUSEBLOCK BLUE IMPORTANT THE BLUE WIRE CAN BE USED TO REMOTELY ACTIVATE AN AUTOMATIC ANTENNA OR AN EXTERNAL AMPLIFIER (SEE ANTENNA OR AMPLIFIER MANUAL) EXISTING ANTENNA CABLE "RADIO" OR "ACCESSORY" FUSE RED SCREW BLACK METAL PART OF DASH (DRILL HOLE IF NECESSARY) CAR BATTERY YELLOW IMPORTANT THIS WIRE MUST BE CONNECTED AS SHOWN OR RADIO WILL NOT OPERATE PROPERLY CONTAINS: FILTER/FUSE ONE 0.
WARNING! l THE AMPLIFIERS IN THIS RADIO ARE ONLY DESIGNED FOR USE WITH 4 SPEAKERS. l NEVER COMBINE (BRIDGE) OUTPUTS FOR USE WITH 2 SPEAKERS. l NEVER GROUND NEGATIVE SPEAKER LEADS TO CHASSIS GROUND. l FAILURE TO WIRE EXACTLY AS SHOWN BELOW MAY CAUSE ELECTRICAL DAMAGE TO THE RADIO.
OPER AT ING INSTRUC INSTRUCTT IONS OPER AT ING INSTRUC INSTRUCTT IONS 1 ON-OFF POWER BUTTON (PWR) If the ignition switch is “on”, press the PWR button to turn the unit on or off. 2 VOLUME/LEVEL CONTROL 5 (VOL UP/DN) To increase the volume level, rotate the AUDIO ADJUST control clockwise in the UP direction. The volume will increase and the level will be shown on the display panel from a minimum of VOL 0 to a maximum of VOL 63.
2 5 TREBLE CONTROL To adjust the treble level, first select the Treble mode by pressing the SEL button so the TRE indication appears on the display panel. Within 5 seconds of choosing the Treble mode, rotate the AUDIO ADJUST control (VOL UP/DN) counter-clockwise (DN) to decrease the treble response or rotate clockwise (UP) to increase it as desired. The level will be shown on the display panel from a minimum TRE-7 to a maximum of TRE 7 (TRE 0 indicates flat response).
OPER AT ING INSTRUC INSTRUCTT IONS bl DISC SELECT ( CD- CD+) During CD changer operation, this button is used to select the desired disc for play. (Refer to function .) bm dl LIQUID CRYSTAL DISPLAY PANEL The Liquid Crystal Display (LCD) panel displays the radio frequency, time, and other active functions. NOTE: It is a characteristic of LCD panels that, if subjected to cold temperatures for an extended period of time, they may take longer to illuminate than under normal conditions.
A light-emitting diode (LED) is located on the chassis behind the front panel, and is visible when the panel assembly is swung down. The LED will flash when the front panel is removed from the front mounting plate. The flashing light serves as a visual warning to the would-be thief that the unit has been disabled by removal of the front panel. bt RESET BUTTON A RESET button is located on the front of the chassis (front panel must be swung down to access the button).
OPERATING INSTRUCTIONS co FUNCTION (LEVEL) DISPLAY F The Function Display consits of five bar graphs which provide a visual representation of the volume level and the left and right channel balance levels. The volume level is represented by three thin bar graphs. As the volume is increased, the number of illuminated segments will increase. The left and right channels are represented by the wider bar graphs.
panel orientation in chassis mounting plate. 3. When taking the front panel with you, please use the supplied carrying case to protect the panel from dirt and damage. Make sure there is no dust or dirt on the electrical terminals on the back of the panel as this could cause intermittent operation or other malfunctions. OPER AT ING INSTRUC INSTRUCTT IONS NOTES ON USE OF FRONT PANEL 1.
SETTING THE CLOCK / SPECIFICATIONS ECIFICATIO SET T ING THE CLOCK 1. Switch the vehicle ignition and radio “on”. 2. Press the Time/Frequency button to call the time display. 3. Press and hold the Time/Frequency Selector button with the time displayed. The entire time display will blink. 4. Rotate the AUDIO ADJUST control clockwise in the VOL DN direction to adjust the hours and AM/PM indication, and counter-clockwise in the VOL UP direction to adjust the minutes to the correct time. 5.
Built into this radio are controls to operate an optional CD changer. Please check with your Rampage/Audiovox car stereo specialist or call 1-800-645-4994 for recommendations of the models that will work with this radio. Adjustment of the audio functions (volume, tone, balance, and fader) for the CD changer operate in the same manner as they do for radio play. The following controls will operate the CD changer when it is installed and connected to this radio.
CD CHANGER ERROR CODES CD CH A NGER ERR OR CODES CHA ERROR If a problem should develop while operating the CD changer, the following error codes may appear on the display panel: ER-1: Indicates that there is no magazine loaded in the CD changer. ER-2: Indicates a problem with the magazine eject function. ER-3: Indicates an error in the disc loading function. ER-4: Indicates an error in the disc un-loading function. ER-5: Indicates an error in the magazine position.
The radio portion of your new sound system does not require any maintenance. We recommend you keep this manual for general reference of the many features found in this unit. As with any cassette player, the cassette section of this sound system does require a minimum of maintenance to keep it in good working condition. The following simple care and maintenance suggestions should be followed to prevent malfunctions of the cassette system. Cassette Care: 1.
12 MONTH LIMI TED W A RR A NT Y LIMITED WA AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned product (at the Company's option) without charge for parts and repair labor.
