User`s manual

ManualsBrandsAudiomatica ManualsAmplifierMODEL 5

171

172

173

174

175

176

177

178

179

180

Table Of Contents

CONTENTS
1 INTRODUCTION
- 1.1 ABOUT THIS MANUAL
  - 1.1.1 WHAT THIS USER MANUAL DOES COVER
- 1.2 GENERAL CONDITIONS AND WARRANTY
2 THE CLIO SYSTEM
- 2.1 THE FW-01 FIREWIRE AUDIO INTERFACE
  - 2.1.1 TECHNICAL SPECIFICATIONS
- 2.2 THE MIC-01 MICROPHONE
- 2.3 THE PRE-01 MICROPHONE PREAMPLIFIER
  - 2.3.1 TECHNICAL SPECIFICATION
  - 2.3.2 USE OF THE PREAMPLIFIER
- 2.4 THE QCBOX MODEL 5 POWER AMPLIFIER, SWITCHING AND TESTING BOX
  - 2.4.1 TECHNICAL SPECIFICATIONS
3 CLIO INSTALLATION
- 3.1 MINIMUM PC CONFIGURATION
- 3.2 FW-01 DRIVERS INSTALLATION UNDER WINDOWS XP
- 3.3 FW-01 DRIVERS INSTALLATION UNDER WINDOWS VISTA AND 7
- 3.4 SOFTWARE INSTALLATION
- 3.5 THE 'CLIO BOX'
- 3.6 RUNNING CLIO FOR THE FIRST TIME
  - 3.6.1 INITIAL TEST
- 3.7 SYSTEM CALIBRATION
  - 3.7.1 CALIBRATION VALIDATION
- 3.8 CLIO SERIAL NUMBER AND DEMO MODE
- 3.9 TROUBLESHOOTING CLIO INSTALLATION
4 CLIO BASICS
- 4.1 INTRODUCTION
- 4.2 GETTING HELP
- 4.3 CLIO DESKTOP
- 4.4 MAIN TOOLBAR
- 4.5 HARDWARE CONTROLS TOOLBAR
- 4.6 QCBOX & LPT CONTROLS
  - 4.6.1 CONTROLLING THE QCBOX 5 POWER AMPLIFIER, SWITCHING AND MEASURING BOX
- 4.7 CONTROLLING TURNTABLES
  - 4.7.1 TURNTABLES OPTIONS DIALOG
- 4.8 MAIN MENU AND SHORTCUTS
- 4.9 BASIC CONNECTIONS
5 SYSTEM OPERATIONS AND SETTINGS
- 5.1 INTRODUCTION
- 5.2 REGISTERED FILE EXTENSIONS
- 5.3 FILE MENU AND MAIN TOOLBAR BUTTONS
- 5.4 OPTIONS
- 5.5 DESKTOP MANAGEMENT
- 5.6 CALIBRATION
- 5.7 STARTUP OPTIONS AND GLOBAL SETTINGS
  - 5.7.1 SAVING MEASUREMENT SETTINGS
6 COMMON MEASUREMENT INTERFACE
- 6.1 INTRODUCTION
- 6.2 UNDERSTANDING THE DISPLAY IN FRONT OF YOU
- 6.3 BUTTONS AND CHECKBOXES
- 6.4 HOW TO ZOOM
- 6.5 SHORTCUTS AND MOUSE ACTIONS
- 6.6 THE MLS TIME DOMAIN DISPLAY
7 SIGNAL GENERATOR
- 7.1 INTRODUCTION
- 7.2 SINUSOID
- 7.3 TWO SINUSOIDS
- 7.4 MULTITONES
- 7.5 WHITE NOISE
- 7.6 MLS
- 7.7 CHIRPS
- 7.8 PINK NOISE
- 7.9 ALL TONES
- 7.10 SIGNAL FILES
  - 7.10.1 SAVING SIGNAL FILES
8 MULTI-METER
- 8.1 INTRODUCTION
- 8.2 MULTI-METER CONTROL PANEL
  - 8.2.1 TOOLBAR BUTTONS
  - 8.2.2 TOOLBAR DROP DOWN LISTS
- 8.3 USING THE MULTI-METER
  - 8.3.1 THE MINIMIZED STATE
  - 8.3.2 CAPTURING THE GLOBAL REFERENCE LEVEL
- 8.4 THE SOUND LEVEL METER
  - 8.4.1 CAPTURING THE MICROPHONE SENSITIVITY
- 8.5 THE LCR METER
  - 8.5.1 MEASURING AN INDUCTOR
- 8.6 INTERACTION BETWEEN THE MULTI-METER AND FFT
9 FFT, RTA AND “LIVE” TRANSFER FUNCTION
- 9.1 INTRODUCTION
- 9.2 NARROWBAND FFT ANALYZER
  - 9.2.1 TOOLBAR BUTTONS, DROP DOWN LISTS AND DISPLAYS
- 9.3 RTA - OCTAVE BANDS ANALYZER
  - 9.3.1 DEDICATED TOOLBAR FUNCTIONS
- 9.4 FFT SETTINGS DIALOG
- 9.5 FFT AND RTA OPERATION
- 9.6 AVERAGING
- 9.7 TIME DATA DISPLAY (OSCILLOSCOPE)
- 9.8 FFT AND MULTI-METER
- 9.9 FFT AND Leq ANALIZER
- 9.10 “LIVE” TRANSFER FUNCTION ANALYZER
  - 9.10.1 DEDICATED ‘LIVE’ TOOLBAR FUNCTIONS
  - 9.10.2 USING CLIO DURING A LIVE PERFORMANCE
10 MLS & LOG CHIRP
- 10.1 INTRODUCTION
- 10.2 MLS & LOG CHIRP CONTROL PANEL
- 10.3 IMPULSE RESPONSE CONTROL PANEL
  - 10.3.1 TOOLBAR BUTTONS
- 10.4 MEASURING FREQUENCY RESPONSE
- 10.5 OTHER TIME DOMAIN INFORMATION
- 10.6 PROCESSING TOOLS BY EXAMPLE
- 10.7 MLS Vs. LOG CHIRP
- 10.8 RELATED MENUS
11 SINUSOIDAL
- 11.1 INTRODUCTION
- 11.2 SINUSOIDAL CONTROL PANEL
- 11.3 HOW TO MEASURE A SIMULTANEOUS FREQUENCY AND IMPEDANCE RESPONSE OF A LOUDSPEAKER
- 11.4 A BRIEF DESCRIPTION ON SETTINGS EFFECTS
- 11.5 DISTORTION AND SETTINGS
12 WATERFALL , DIRECTIVITY & 3D
- 12.1 INTRODUCTION
- 12.2 WATERFALL, DIRECTIVITY & 3D CONTROL PANEL
  - 12.2.1 COMMON TOOLBAR BUTTONS AND DROP DOWN LISTS
- 12.3 WATERFALL SPECIFIC CONTROLS
  - 12.3.1 WATERFALL SETTINGS
  - 12.3.2 WATERFALL OPERATION
- 12.4 MAKING A CUMULATIVE SPECTRAL DECAY
- 12.5 DIRECTIVITY SPECIFIC CONTROLS
  - 12.5.1 DIRECTIVITY SETTINGS AND OPERATION
- 12.6 MEASURING LOUDSPEAKER SINGLE POLAR DATA (1D MODE)
- 12.7 REPRESENTING SINGLE POLAR DATA
- 12.8 3D SPECIFIC CONTROLS
  - 12.8.1 3D SETTINGS AND OPERATION
- 12.9 MEASURING LOUDSPEAKER SINGLE POLAR DATA (3D MODE)
- 12.10 MEASURING FULL SPHERE LOUDSPEAKER POLAR DATA (3D MODE)
- 12.11 REPRESENTING 3D BALLOON DATA
- 12.12 EXPORT 3D BALLOON DATA
13 MEASURING IMPEDANCE AND T&S PARAMETERS
- 13.1 INTRODUCTION
- 13.2 GENERALS
- 13.3 INTERNAL MODE
- 13.4 I SENSE
- 13.5 CONSTANT VOLTAGE & CONSTANT CURRENT
  - 13.5.1 CONSTANT VOLTAGE
  - 13.5.2 CONSTANT CURRENT
- 13.6 IMPEDANCE: SINUSOIDAL OR MLS
- 13.7 THIELE & SMALL PARAMETERS
14 LINEARITY & DISTORTION
- 14.1 INTRODUCTION
- 14.2 LINEARITY & DISTORTION CONTROL PANEL
  - 14.2.1 TOOLBAR DROP DOWN LIST
  - 14.2.2 LINEARITY & DISTORTION SETTINGS DIALOG
15 ACOUSTICAL PARAMETERS
- 15.1 INTRODUCTION
- 15.2 THE ACOUSTICAL PARAMETERS CONTROL PANEL
  - 15.2.1 TOOLBAR BUTTONS AND DROP DOWN LISTS
  - 15.2.2 INTERACTION WITH THE A.P. CONTROL PANEL
- 15.3 ACOUSTICAL PARAMETERS SETTINGS
- 15.4 THE CALCULATED ACOUSTICAL PARAMETERS
- 15.5 NOTES ABOUT ACOUSTICAL PARAMETERS MEASUREMENT
- 15.6 STI CALCULATION
16 Leq LEVEL ANALYSIS
- 16.1 INTRODUCTION
- 16.2 THE Leq CONTROL PANEL
  - 16.2.1 TOOLBAR BUTTONS AND DROP DOWN LISTS
  - 16.2.2 INTERACTION WITH THE Leq CONTROL PANEL
- 16.3 Leq SETTINGS
17 WOW AND FLUTTER
- 17.1 INTRODUCTION
- 17.2 WOW & FLUTTER CONTROL PANEL
  - 17.2.1 TOOLBAR BUTTON
  - 17.2.2 TOOLBAR DROP DOWN LIST
- 17.3 FEATURES
18 WAVELET ANALYSIS
- 18.1 INTRODUCTION
- 18.2 WAVELET ANALYSIS CONTROL PANEL
  - 18.2.1 COMMON TOOLBAR BUTTONS AND DROP DOWN LISTS
- 18.3 WAVELET ANALYSIS SETTINGS
- 18.4 WAVELET ANALYSIS OPERATION
  - 18.4.1 TRADING BANDWIDTH AND TIME RESOLUTION
  - 18.4.2 NORMALIZED SCALOGRAMS
BIBLIOGRAPHY
NORMS

12.12.1 EXPORT EASE .XHN AND CLF V2 .TAB FILES

In case of EASE .xhn and CLF v2 .tab format is selected in the File And Export

Format Group then the General Information, On Axis Response and Impedance &

Power groups are active.

Output File defines the file name and location where the file will be saved; it is

possible to choose it clicking on the browse for Choose Output File button (...).

The Loudspeaker Name and Manufacturer Name fields will be used into the

exported text file.

The Frequency Range can go from 100 Hz to 10 kHz in case of EASE .xhn, from

25 Hz to 20 kHz in case of CLF v2 .tab. The frequency range to export can be

modified using the combo boxes.

The On-Axis Response group let the user decide to use the data set on-axis

measurement or use an MLS file as on-axis reference. It is also possible to apply a

Level Shift to our measured response to correct for power and distance different

from the required 1W/1m. A basic calculation that calculates the required level shift

as function of the Drive Level in W applied and Measurement Distance between

loudspeaker and microphone.

Similarly to the previous group, the Impedance & Power group let the user decide

to use a real measured impedance in .sini format or a nominal value. Into the same

group the user can specify a power level (valid for all bands) for the source.

It is clear that the functions of this export menu are minimal, but they successfully

meet the user need to create loudspeaker models used by the most common

simulation software.

Once the output text file is saved, it may be necessary to preprocess with a text

editor to add or modify information.

Figure 12.33 report an example of a data set exported to CLF v2. tab format and

imported by the CLF software.

figure 12.33

12 WATERFALL , DIRECTIVITY & 3D 179