User`s manual

ManualsBrandsAudiomatica ManualsAmplifierMODEL 5

161

162

163

164

165

166

167

168

169

170

Table Of Contents

CONTENTS
1 INTRODUCTION
- 1.1 ABOUT THIS MANUAL
  - 1.1.1 WHAT THIS USER MANUAL DOES COVER
- 1.2 GENERAL CONDITIONS AND WARRANTY
2 THE CLIO SYSTEM
- 2.1 THE FW-01 FIREWIRE AUDIO INTERFACE
  - 2.1.1 TECHNICAL SPECIFICATIONS
- 2.2 THE MIC-01 MICROPHONE
- 2.3 THE PRE-01 MICROPHONE PREAMPLIFIER
  - 2.3.1 TECHNICAL SPECIFICATION
  - 2.3.2 USE OF THE PREAMPLIFIER
- 2.4 THE QCBOX MODEL 5 POWER AMPLIFIER, SWITCHING AND TESTING BOX
  - 2.4.1 TECHNICAL SPECIFICATIONS
3 CLIO INSTALLATION
- 3.1 MINIMUM PC CONFIGURATION
- 3.2 FW-01 DRIVERS INSTALLATION UNDER WINDOWS XP
- 3.3 FW-01 DRIVERS INSTALLATION UNDER WINDOWS VISTA AND 7
- 3.4 SOFTWARE INSTALLATION
- 3.5 THE 'CLIO BOX'
- 3.6 RUNNING CLIO FOR THE FIRST TIME
  - 3.6.1 INITIAL TEST
- 3.7 SYSTEM CALIBRATION
  - 3.7.1 CALIBRATION VALIDATION
- 3.8 CLIO SERIAL NUMBER AND DEMO MODE
- 3.9 TROUBLESHOOTING CLIO INSTALLATION
4 CLIO BASICS
- 4.1 INTRODUCTION
- 4.2 GETTING HELP
- 4.3 CLIO DESKTOP
- 4.4 MAIN TOOLBAR
- 4.5 HARDWARE CONTROLS TOOLBAR
- 4.6 QCBOX & LPT CONTROLS
  - 4.6.1 CONTROLLING THE QCBOX 5 POWER AMPLIFIER, SWITCHING AND MEASURING BOX
- 4.7 CONTROLLING TURNTABLES
  - 4.7.1 TURNTABLES OPTIONS DIALOG
- 4.8 MAIN MENU AND SHORTCUTS
- 4.9 BASIC CONNECTIONS
5 SYSTEM OPERATIONS AND SETTINGS
- 5.1 INTRODUCTION
- 5.2 REGISTERED FILE EXTENSIONS
- 5.3 FILE MENU AND MAIN TOOLBAR BUTTONS
- 5.4 OPTIONS
- 5.5 DESKTOP MANAGEMENT
- 5.6 CALIBRATION
- 5.7 STARTUP OPTIONS AND GLOBAL SETTINGS
  - 5.7.1 SAVING MEASUREMENT SETTINGS
6 COMMON MEASUREMENT INTERFACE
- 6.1 INTRODUCTION
- 6.2 UNDERSTANDING THE DISPLAY IN FRONT OF YOU
- 6.3 BUTTONS AND CHECKBOXES
- 6.4 HOW TO ZOOM
- 6.5 SHORTCUTS AND MOUSE ACTIONS
- 6.6 THE MLS TIME DOMAIN DISPLAY
7 SIGNAL GENERATOR
- 7.1 INTRODUCTION
- 7.2 SINUSOID
- 7.3 TWO SINUSOIDS
- 7.4 MULTITONES
- 7.5 WHITE NOISE
- 7.6 MLS
- 7.7 CHIRPS
- 7.8 PINK NOISE
- 7.9 ALL TONES
- 7.10 SIGNAL FILES
  - 7.10.1 SAVING SIGNAL FILES
8 MULTI-METER
- 8.1 INTRODUCTION
- 8.2 MULTI-METER CONTROL PANEL
  - 8.2.1 TOOLBAR BUTTONS
  - 8.2.2 TOOLBAR DROP DOWN LISTS
- 8.3 USING THE MULTI-METER
  - 8.3.1 THE MINIMIZED STATE
  - 8.3.2 CAPTURING THE GLOBAL REFERENCE LEVEL
- 8.4 THE SOUND LEVEL METER
  - 8.4.1 CAPTURING THE MICROPHONE SENSITIVITY
- 8.5 THE LCR METER
  - 8.5.1 MEASURING AN INDUCTOR
- 8.6 INTERACTION BETWEEN THE MULTI-METER AND FFT
9 FFT, RTA AND “LIVE” TRANSFER FUNCTION
- 9.1 INTRODUCTION
- 9.2 NARROWBAND FFT ANALYZER
  - 9.2.1 TOOLBAR BUTTONS, DROP DOWN LISTS AND DISPLAYS
- 9.3 RTA - OCTAVE BANDS ANALYZER
  - 9.3.1 DEDICATED TOOLBAR FUNCTIONS
- 9.4 FFT SETTINGS DIALOG
- 9.5 FFT AND RTA OPERATION
- 9.6 AVERAGING
- 9.7 TIME DATA DISPLAY (OSCILLOSCOPE)
- 9.8 FFT AND MULTI-METER
- 9.9 FFT AND Leq ANALIZER
- 9.10 “LIVE” TRANSFER FUNCTION ANALYZER
  - 9.10.1 DEDICATED ‘LIVE’ TOOLBAR FUNCTIONS
  - 9.10.2 USING CLIO DURING A LIVE PERFORMANCE
10 MLS & LOG CHIRP
- 10.1 INTRODUCTION
- 10.2 MLS & LOG CHIRP CONTROL PANEL
- 10.3 IMPULSE RESPONSE CONTROL PANEL
  - 10.3.1 TOOLBAR BUTTONS
- 10.4 MEASURING FREQUENCY RESPONSE
- 10.5 OTHER TIME DOMAIN INFORMATION
- 10.6 PROCESSING TOOLS BY EXAMPLE
- 10.7 MLS Vs. LOG CHIRP
- 10.8 RELATED MENUS
11 SINUSOIDAL
- 11.1 INTRODUCTION
- 11.2 SINUSOIDAL CONTROL PANEL
- 11.3 HOW TO MEASURE A SIMULTANEOUS FREQUENCY AND IMPEDANCE RESPONSE OF A LOUDSPEAKER
- 11.4 A BRIEF DESCRIPTION ON SETTINGS EFFECTS
- 11.5 DISTORTION AND SETTINGS
12 WATERFALL , DIRECTIVITY & 3D
- 12.1 INTRODUCTION
- 12.2 WATERFALL, DIRECTIVITY & 3D CONTROL PANEL
  - 12.2.1 COMMON TOOLBAR BUTTONS AND DROP DOWN LISTS
- 12.3 WATERFALL SPECIFIC CONTROLS
  - 12.3.1 WATERFALL SETTINGS
  - 12.3.2 WATERFALL OPERATION
- 12.4 MAKING A CUMULATIVE SPECTRAL DECAY
- 12.5 DIRECTIVITY SPECIFIC CONTROLS
  - 12.5.1 DIRECTIVITY SETTINGS AND OPERATION
- 12.6 MEASURING LOUDSPEAKER SINGLE POLAR DATA (1D MODE)
- 12.7 REPRESENTING SINGLE POLAR DATA
- 12.8 3D SPECIFIC CONTROLS
  - 12.8.1 3D SETTINGS AND OPERATION
- 12.9 MEASURING LOUDSPEAKER SINGLE POLAR DATA (3D MODE)
- 12.10 MEASURING FULL SPHERE LOUDSPEAKER POLAR DATA (3D MODE)
- 12.11 REPRESENTING 3D BALLOON DATA
- 12.12 EXPORT 3D BALLOON DATA
13 MEASURING IMPEDANCE AND T&S PARAMETERS
- 13.1 INTRODUCTION
- 13.2 GENERALS
- 13.3 INTERNAL MODE
- 13.4 I SENSE
- 13.5 CONSTANT VOLTAGE & CONSTANT CURRENT
  - 13.5.1 CONSTANT VOLTAGE
  - 13.5.2 CONSTANT CURRENT
- 13.6 IMPEDANCE: SINUSOIDAL OR MLS
- 13.7 THIELE & SMALL PARAMETERS
14 LINEARITY & DISTORTION
- 14.1 INTRODUCTION
- 14.2 LINEARITY & DISTORTION CONTROL PANEL
  - 14.2.1 TOOLBAR DROP DOWN LIST
  - 14.2.2 LINEARITY & DISTORTION SETTINGS DIALOG
15 ACOUSTICAL PARAMETERS
- 15.1 INTRODUCTION
- 15.2 THE ACOUSTICAL PARAMETERS CONTROL PANEL
  - 15.2.1 TOOLBAR BUTTONS AND DROP DOWN LISTS
  - 15.2.2 INTERACTION WITH THE A.P. CONTROL PANEL
- 15.3 ACOUSTICAL PARAMETERS SETTINGS
- 15.4 THE CALCULATED ACOUSTICAL PARAMETERS
- 15.5 NOTES ABOUT ACOUSTICAL PARAMETERS MEASUREMENT
- 15.6 STI CALCULATION
16 Leq LEVEL ANALYSIS
- 16.1 INTRODUCTION
- 16.2 THE Leq CONTROL PANEL
  - 16.2.1 TOOLBAR BUTTONS AND DROP DOWN LISTS
  - 16.2.2 INTERACTION WITH THE Leq CONTROL PANEL
- 16.3 Leq SETTINGS
17 WOW AND FLUTTER
- 17.1 INTRODUCTION
- 17.2 WOW & FLUTTER CONTROL PANEL
  - 17.2.1 TOOLBAR BUTTON
  - 17.2.2 TOOLBAR DROP DOWN LIST
- 17.3 FEATURES
18 WAVELET ANALYSIS
- 18.1 INTRODUCTION
- 18.2 WAVELET ANALYSIS CONTROL PANEL
  - 18.2.1 COMMON TOOLBAR BUTTONS AND DROP DOWN LISTS
- 18.3 WAVELET ANALYSIS SETTINGS
- 18.4 WAVELET ANALYSIS OPERATION
  - 18.4.1 TRADING BANDWIDTH AND TIME RESOLUTION
  - 18.4.2 NORMALIZED SCALOGRAMS
BIBLIOGRAPHY
NORMS

12.6.2 PREPARING THE TURNTABLE

Open the Turntables Control dialog and select the connected turntable (See 4.7).

Outline ET/ST (TTL Pulse)

We assume that the Outline ET/ST turntable is properly connected to your PC

(refer to 4.7.1 for details). To prepare for this measurement session you need

to:

1) Manually set the front selector labeled 'Deg Step' to 5°.

2) Rotate the turntable counterclockwise until you reach the desired start

position: as we want to start from -180° position it at 180°.

3) Recall the Turntable Settings dialog (Fig.12.12), set Resolution at 5°, Speed

at 0.75 RPM

Figure 12.12

In order to link the TTL pulse generation to measurements leave the

Turntables Control dialog open during the measurements.

Outline ET250-3D or LinearX LT360

We assume the turntable is properly connected to your PC (refer to 4.7.1 for

details). To prepare this measurement session you need to:

1) Set the turntable step to 5° using the turntable specific supplied software or

turntable panel hardware controls

2) Rotate the turntable counterclockwise until you reach the desired start

position: as we want to start from -180° position it at 180°.

In order to link the turntables to measurements leave the Turntables

Control dialog open and the turntable linked during the measurements.

12.6.3 TAKING THE MEASUREMENTS

You are now ready to begin the measuring session. We suggest you to take an

initial measurement (with the speaker in place over the turntable) to verify all the

parameters, especially viewing the acquired impulse response and setting the start

and stop values of the measurement window. These values will be applied to all the

measurements taken; consider, in this respect, the problem of the trajectory of the

acoustic center of the speaker during the rotation.

12 WATERFALL , DIRECTIVITY & 3D 165