New Zealand SENSOR 500 Dedicated Network services telephone User guide
The SENSOR 500 is a dedicated network services telephone. SENSOR 500 is compatible with Caller ID, Call Answer and message waiting network services. In addition it is also pre-programmed for access to other optional services. Up to 10-speed dial memories and 20 name and number phonebook add to its versatility Other features include: headset socket, on-hook dialling and a choice of 12 languages for the display text.
SENSOR 500 Installation.................................. 3 Location of controls............... 3 Connection............................ 4 Wall mounting........................ 5 Headset..................................5 Select language..................... 5 Display....................................6 Set date and time...................6 Using the telephone................... 7 Making a call.......................... 7 On the hook dialing................7 Using a headset.....................
LOCATION OF CONTROLS 1 2 3 4 5 6 7 8 9 10 11 12 13 3 Handset Curly cord socket Wall mounting hook Hook switch Dial-Up key Scroll call list/phonebook, replay Line cord socket (rear) Display Message waiting indicator Play/Pause messages Headset socket (rear) Switch between speaker/headset Switch for ringer level 14 15 16 17 18 19 20 21 22 23 24 25 Erase key Scroll call list/phonebook, save Speed-dial/pre-programmed keys Volume control for handset Volume control for speaker Mute key Key/indicator for speak
CONNECTION TO THE TELEPHONE NETWORK · Connect the curly cord to the left-hand side of the telephone and to the bottom of the handset. · Connet the power cord to middle socket of telephone and plug into power outlet. · Connect the telephone line cord to the socket entitled “LINE” on the rear of the telephone and then connect the cord to the network wall outlet. The display will show: NO CALLS. Line Headset socket Line cord socket Plug pack power To connect headset, see page 4.
WALL MOUNTING The phone can be wall mounted, using the bracket supplied. Use the bracket supplied to mark the position of screw holes on the wall. Drill the holes (check for hidden pipes, etc). Use the raw plug and screws, ensuring approximately 3 mm remain between the wall and the head of the screw. Connect the bracket to the rear of the base unit and place the complete assembly above the screws and gently push it down onto the screws. Rotate the handset hanger hook 180 degrees.
DISPLAY When the unit is in standby mode the display will show: the current date and time, if new calls have been received (if these have not been reviewed or answered) and the total number of calls on the call list. Text information 8888888888888 Numbers 88 88 :88 88/18 New calls No./ Time Position Date SET DATE AND TIME The current date and time will be set automatically once a call is received.
MAKING A CALL A call can be made in several different ways, using the handset, on-hook dialling or headset. USING the HANDSET 1. Lift the handset and wait for dial tone. 2. Dial the phone number required. · To terminate the call replace the handset. You can change to speaker/headset during a call by pressing and replacing the handset. Note: Ensure the switch on the right hand side is set to the desired function headset/speaker. USING the ON-HOOK DIALING 1.
LAST NUMBER REDIAL If the last number dialled was engaged or the call was not answered, it is possible to redial the number using the button. · Press and release . The telephone number will be dialled automatically. · When the called party answers, lift the handset (or headset) to converse. If the call is not answered, press and release It’s also possible to lift the handset and then press the redial key.
CALLER DISPLAY Caller display allows you to see who is calling before you answer a call and to see who has called in your absense. When the service is implemented on your telephone line, seconds before your telephone rings the number of the incomming caller will appear on the display. Up to 60 incomming numbers can be stored in the call list. When the list is full, the oldest number will be deleted automatically. It is not possible to view the call list and take a new call at the same time.
REVIEWING PHONE NUMBER Scroll the memory with the keys or . The key Scrolls from the oldest number. The key Scrolls from the latest number. The time and date each call is received is shown on the display. If the number is stored iin the phonebook the corresponding name is also shown. 9 - 2805000 17 10 :56 14/10 Phone number 9-2805000, received at 10:56 the 14th October. Position number 17.
ERASE PHONE NUMBER(S) You may erase a single number or all numbers on the call list. ERASE A NUMBER · Scroll the call list until the number to be erased is shown on the display. · Press C twice quickly, then release ERASE ALL NUMBERS · Scroll the call list until a number is shown on the display. · Press and hold C until the display shows ”ERASE ALL?”., then release. · Press and release C again. All phone numbers are now erased.
SPEED-DIAL MEMORIES Ten ‘One-touch’ speed dial memories are available. Memories 1 & 2, 6 & 7 have been pre-programmed for easy access to and set of for select services. If required these memories can be re-programmed with numbers of your own choice following the procedure below. Memroy 1 = Call waiting answer / Call hold Memory 2 = Stop your telephone number being displayed for this call Memory 6 = Program call foward always Memory 7 = Turn Call foward always off STORE NUMBER/NAME 1. Press . 2.
STORE NUMBER/NAME The telephone has a phone book where you can store 20 names and telephone numbers for easy access and fast dialling. When one of these phone numbers calls, both name and number will be displayed. In stand-by display will alternate between NEW CALLS and VIP on the upper line. This ensures that you see when a call that matches a number in the phone book (or speed-dial memory) is received.
STORE NUMBER/NAME 1. Press and release . The display shows how many numbers/ names are stored in the phonebook. 2. Press . 3. Dial the full number to be stored as you would manually dial that number (16 digits maximum). 4. Press and release . 5. Enter a name. (15 letters maximum) by pressing the relevant keypad digit buttons once or several times (see page 13) - If you have to enter the same letter twice, press and release onto the next position - For edit, press . - To make a space, press 0. 6.
CALL ANSWERING To check your messages, simply press Play and your messages will be played to you. Whilst listening to your messages you can use the keys featured below to operate various options. Backwards Pause/Play Forward Erase current message To use the other features of the network service, press the corresponding key.
RE-PROGRAM FOR ALTERNATIVE CALL ANSWERING SERVICE If the pre-programmed keys are not compatible with your network operators answering service, it is possible to re-program the keys. · Press. · Press and hold down until the display shows text, then release · Enter digit (s) to store · Press the key required. · Press · Press to store to finish.
TROUBLE SHOOTING THE RED LED INDICATOR ON THE BASE UNIT IS FLASHING · There is a message waiting in your Network voice message system. INCOMING NUMBERS ARE NOT VISIBLE ON THE DISPLAY · Have you subscribed to the caller display service? · If “Out of area” or “Withheld Secret” are displayed, it either means that no information of the number is available or that the caller has withheld their number. · Is the phone connected to a PABX? Caller display is not available when connected to a PABX.
GUARANTEE If you believe your SENSOR 500 is malfunctioning, please refer to the relevant section and/or consult the troubleshooting guide in this manual to ensure that you have followed the instructions carefully. The SENSOR 500 is warranted for a period of 12 months from the date of purchase by you, the end user. In the unlikely event of a fault during this period. please contact our Helpline for assistance.
