Specifications

ManualsBrandsAudioControl ManualsAutomotiveMP-200

Crestron MPS-200

Multimedia Presentation System 200

Operations Guide

Summary of content (94 pages)

PAGE 1
Crestron MPS-200 Multimedia Presentation System 200 Operations Guide
PAGE 2
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Important Safety Instructions • Read these instructions. • Keep these instructions. • Heed all warnings. • Follow all instructions. • Do not use this apparatus near water. • Clean only with dry cloth. • Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
PAGE 3
Crestron MPS-200 Multimedia Presentation System 200 Contents Multimedia Presentation System 200: MPS-200 1 Introduction ............................................................................................................................... 1 Features and Functions ................................................................................................ 1 Applications.................................................................................................................
PAGE 4
PAGE 5
Crestron MPS-200 Multimedia Presentation System 200 Multimedia Presentation System 200: MPS-200 Introduction Features and Functions • • • • • • • • • • • • • • • • System switcher, audio processor, and control system Out-of-the-box switching and audio control Four video/HDTV and four RGB/computer inputs Built-in input signal sensing | auto-switching capable Separate display and touchpanel preview outputs QuickMedia™ and Crestron Home® CAT5 AV connectivity Eight balanced stereo audio inputs | Two gated m
PAGE 6
Multimedia Presentation System 200 Crestron MPS-200 status information to the control system. Selectable sync impedance on the RGB inputs helps accommodate cable runs of varying lengths. Touchpanel Output A second discrete output is provided on the MPS-200 to feed a preview signal to the system touchpanel or other monitor. This output is controlled separately from the main display output, allowing a different source to be viewed.
PAGE 7
Crestron MPS-200 Multimedia Presentation System 200 Front Panel Control Out of the box, the MPS-200 front panel supports easy pushbutton routing of input sources to each of the outputs, and audio volume adjustment using the volume control knob. Dedicated buttons and indicators are also provided for separate control of system power and projector power. In addition, five preset buttons are included for custom functions such as lowering a projection screen, closing blinds, or selecting a lighting preset.
PAGE 8
Multimedia Presentation System 200 Crestron MPS-200 Applications The following diagram shows an MPS-200 in a lecture hall application. MPS-200 in a Lecture Hall Application For more information on this and other QM applications, refer to the latest revision of the Crestron MediaManager Applications Guide (Doc. 6244), which is available from the Crestron website (http://www.crestron.com/manuals). 4 • Multimedia Presentation System 200: MPS-200 Operations Guide – DOC.
PAGE 9
Crestron MPS-200 Multimedia Presentation System 200 Internal Block Diagram The following diagrams represent the video and audio switching abilities of the MPS-200. For more information refer to “Configuration ” on page 35.
PAGE 10
Multimedia Presentation System 200 Crestron MPS-200 Audio Block Diagram of the MPS-200 INPUTS 1 2 3 OUTPUTS Stereo Audio Stereo Audio Replicate This Section for Record Out Stereo Audio L 4 6 7 Stereo Audio Stereo 8x2 Matrix Switch A/D Vol/EQ Program L D/A Mute D/A Mute D/A Mute 3 Channel Mixer 5 Stereo Audio Stereo Audio R Program R Stereo Audio Vol/EQ Stereo Audio Speech 3 Channel Mixer 8 Delay A/D QM ENCODER 2 Local Mic With Phantom Power Local Mic With Phantom Power A/
PAGE 11
Crestron MPS-200 Multimedia Presentation System 200 MPS-200 Specifications (Continued) SPECIFICATION DETAILS Video/RGB Switcher 8x2(x5) crosspoint matrix, 1x4 video/RGB output selector Signal Types RGB and composite, S-video, or component video (does not transcode) Video/HDTV Formats NTSC or PAL, HDTV up to 1080i/1080p RGB Formats RGBHV or RGBS Maximum Resolution QXGA 2048 X 1536 @ 60Hz (WUXGA 1920 X 1200 @ 60Hz via QM) Blanking Time < 0.1 second Sync Rise/Fall Time 3.
PAGE 12
Multimedia Presentation System 200 Crestron MPS-200 MPS-200 Specifications (Continued) SPECIFICATION DETAILS Audio (continued) GEQ Filter Gain ±12dB, 0.1dB steps GEQ Filter Center Frequencies 31.5, 63, 125, 250, 500, 1k, 2k, 4k, 8k, 16k Hz Speech Output Delay 0 to 40 ms, 1 ms steps Frequency Response PROG/REC OUT 20Hz to 20kHz ±0.5dB SPEECH OUT 50Hz to 20kHz ±0.5dB SPEAKER (8 ohms) 20Hz to 20kHz ±0.5dB SPEAKER (70V or 100V) 100Hz to 20kHz ±1.
PAGE 13
Crestron MPS-200 Multimedia Presentation System 200 MPS-200 Specifications (Continued) SPECIFICATION DETAILS Enclosure Chassis Steel, black matte powder coat finish, convection-cooled, vented top and sides Faceplate Extruded aluminum, black matte powder coat finish with polycarbonate label overlay Mounting Freestanding or 2U 19-inch rack-mountable (adhesive feet and rack ears included) Dimensions Height 3.47 in (8.81 cm) Width 17.03 in (43.24 cm); 19.00 in (48.26 cm) with ears Depth 12.
PAGE 14
Multimedia Presentation System 200 Crestron MPS-200 Physical Description This section provides information on the connections, controls and indicators available on your MPS-200. MPS-200 Physical View (Front) MPS-200 Physical View (Rear) 10 • Multimedia Presentation System 200: MPS-200 Operations Guide – DOC.
PAGE 15
Crestron MPS-200 Multimedia Presentation System 200 MPS-200 Overall Dimensions 12.54 in (31.86 cm) 11.47 in (29.13 cm) 17.03 in (43.24 cm) 3.47 in (8.81 cm) Operations Guide – DOC.
PAGE 16
Multimedia Presentation System 200 Crestron MPS-200 MPS-200 Buttons and Ports 9 12 16 20 23 30 1 2 3 4 5 10 24 11 13 14 15 17 19 21 22 18 25 26 27 29 31 32 6 7 8 28 12 • Multimedia Presentation System 200: MPS-200 Operations Guide – DOC.
PAGE 17
Crestron MPS-200 Multimedia Presentation System 200 Connectors, Controls & Indicators # CONNECTORS1, CONTROLS & INDICATORS DESCRIPTION 1 NET LED Indicates communication with Cresnet devices. 2 MSG LED Illuminates when a message is present in the message log. To view the contents of the message log, use the front panel buttons or Crestron Toolbox. 3&4 RESET BUTTONS 5 COMPUTER Pin 4 Pin 3 Pin 1 6 Pin 2 MC/LN 1 – 2 HW-R – Initiates system hardware reset.
PAGE 18
Multimedia Presentation System 200 Crestron MPS-200 Connectors, Controls & Indicators (Continued) # CONNECTORS1, CONTROLS & INDICATORS DESCRIPTION 8 VIDEO INPUTS 1 - 4 (4) sets of (3) BNC female video inputs, each set configurable as: • (1) Component/HDTV (YPbPr) video input, or • (1) S-video (Y/C) input, or • (1) Composite input Input Level: 1 Vp-p nominal; Input Impedance: 75 ohms nominal; DC Offset: Insensitive to DC offset (AC coupled); Video signal sensing on COMP/Pb and Y/Y 9 SYSTEM POW
PAGE 19
Crestron MPS-200 Multimedia Presentation System 200 Connectors, Controls & Indicators (Continued) # CONNECTORS1, CONTROLS & INDICATORS 15 SPEAKER OUTPUTS DESCRIPTION (1 or 2) 2-pin 7.62mm detachable terminal blocks; Speaker-level audio outputs (MPS-200); (1) 2-pin 7.
PAGE 20
Multimedia Presentation System 200 Crestron MPS-200 Connectors, Controls & Indicators (Continued) # CONNECTORS1, CONTROLS & INDICATORS DESCRIPTION 18 OUTPUT 1 Contains composite, S-video (Y/C), component (Y, Pb, Pr) and RGBHV outputs on six BNC connectors and one DB15HD connector. Composite Output: (1) BNC female composite video output Output Level: 1.0 to 1.
PAGE 21
Crestron MPS-200 Multimedia Presentation System 200 Connectors, Controls & Indicators (Continued) # CONNECTORS1, CONTROLS & INDICATORS 22 RELAY DESCRIPTION (1) 8-pin 3.5mm detachable terminal block; Comprises (4) normally open, isolated relays; Rated 1 Amp, 30 Volts AC/DC; MOV arc suppression across contacts 23 FUNCTION BUTTONS (5) pushbuttons and red LEDs, programmable for any control system function.
PAGE 22
Multimedia Presentation System 200 Crestron MPS-200 Connectors, Controls & Indicators (Continued) # CONNECTORS1, CONTROLS & INDICATORS 27 TOUCH PANEL OUT DESCRIPTION Contains one CH port and one QM port.
PAGE 23
Crestron MPS-200 Multimedia Presentation System 200 Connectors, Controls & Indicators (Continued) # CONNECTORS1, CONTROLS & INDICATORS 30 OUTPUT SELECTION (2) pushbuttons and red LEDs, select output destination 31 NET (4) 4-pin 3.5mm detachable terminal blocks; DESCRIPTION Cresnet Master ports, paralleled; Available Cresnet Power: 30 Watts Pin 1 Pin 2 Pin 3 Pin 4 100 – 240V ~2.5A 50/60 Hz (POWER SUPPLY) 32 1. 2. 3.
PAGE 24
Multimedia Presentation System 200 Crestron MPS-200 Industry Compliance This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc. (E302724) As of the date of manufacture the MPS-200 has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. NOTE: This device complies with part 15 of the FCC rules.
PAGE 25
Crestron MPS-200 Multimedia Presentation System 200 Setup Network Wiring When wiring the network, consider the following: • Use Crestron Certified Wire. • Provide sufficient power to the system. CAUTION: Insufficient power can lead to unpredictable results or damage to the equipment. Please use the Crestron Power Calculator to help calculate how much power is needed for the system (http://www.crestron.com/calculators).
PAGE 26
Multimedia Presentation System 200 Crestron MPS-200 QuickMedia Wiring The Crestron QuickMedia cable (sold under the name “CresCAT-QM”) contains one CAT5E cable and one Cresnet cable in Siamese jackets. Installation of any QM device is as simple as installing CresCAT-QM wires from the output of one device to the input of another. Installations are flexible, affordable and fast. For more information, refer to the latest revision of the Crestron MediaManager Applications Guide (Doc. 6244).
PAGE 27
Crestron MPS-200 Multimedia Presentation System 200 QM Network Topology Midpoints Origination Points QM MPS-200 Endpoints QM QM-MD7x2 QM QM TPS-12G/15G-QM-L QM-MD7x2 QM MPS-200 TPS-12G/15G-QM-L QM MPS-200 Installation Ventilation The MPS-200 should be used in a well-ventilated area. The venting holes should not be obstructed under any circumstances. If the MPS-200 is hot to the touch, consider using forced air ventilation and/or incrementing the spacing between units.
PAGE 28
Multimedia Presentation System 200 Crestron MPS-200 Ear Attachment for Rack Mounting 4. Repeat procedure (steps 1 through 3) to attach the remaining ear to the opposite side. NOTE: The sync input impedance and DDC feature should be set prior to placing the MPS-200 in an equipment rack. For more information, refer to “Configure the RGB Input Ports” on page 27.
PAGE 29
Crestron MPS-200 Multimedia Presentation System 200 Hardware Connections for the MPS-200, Rear PROGRAM AUDIO OUTPUT: TO AMPLIFIER OR AMPLIFIED SPEAKERS MICROPHONE/LINE INPUT: FROM MICROPHONE OR LINE-LEVEL SOURCES IR IN: FROM CNXRMIRD IR RECEIVER SPEECH OUTPUT: TO AMPLIFIER OR AMPLIFIED SPEAKERS RECORD OUTPUT: TO CODEC, RECORDING DEVICE, OR ASSISTIVE LISTENING SYSTEM IR/SERIAL OUT: TO IRP2 IR EMITTER PROBE or ONE-WAY SERIAL CONTROLLED DEVICES RELAY OUTPUT: TO CONTROLLABLE DEVICES INPUT: FROM DEVICE
PAGE 30
Multimedia Presentation System 200 Crestron MPS-200 NOTE: When running the out-of-the-box program and connecting a projector screen, the “up” control lines should be connected to relay 1 and the “down” control lines should be connected to relay 2. NOTE: To analyze Cresnet lines, the C2N-ANLZ is required. For instructions, refer to the latest version of the C2N-ANLZ Operations Guide (Doc. 6473). Balanced and unbalanced audio inputs/outputs are provided, utilizing five-pin terminal block connectors.
PAGE 31
Crestron MPS-200 Multimedia Presentation System 200 Configure the RGB Input Ports Each of the RGB input ports feature a set of six DIP switches located inside the MPS-200. These switches are used to set the sync input impedance of each port and simulate the presence of a monitor (DDC) for each RGB input. The sync input impedance can be set to either 1k, 500, or 75 ohms. The setting from the factory is 1k ohms and should work with most RGB sources.
PAGE 32
Multimedia Presentation System 200 Crestron MPS-200 DIP Switch Location DIP SWITCHES LOCATED UNDER ACCESS PANEL Set the DIP Switches 1. Referring to the following table, set the DIP switches of each RGB input port to the required sync input impedance and DDC functionality.
PAGE 33
Crestron MPS-200 Label the Buttons Operations Guide – DOC. 6528B Multimedia Presentation System 200 Use Crestron Engraver software to print custom labels for the MPS-200’s front panel buttons and LEDS. Crestron recommends printing on 100-pound paper. Paper weighing less than 100 pounds will tend to crumple while sliding in, while paper weighing more than 100 pounds may not fit.
PAGE 34
Multimedia Presentation System 200 Crestron MPS-200 Programming Software Have a question or comment about Crestron software? Answers to frequently asked questions (FAQs) can be viewed in the Online Help section of the Crestron website. To post a question or view questions you have submitted to Crestron’s True Blue Support, log in at http://support.crestron.com. First-time users will need to establish a user account.
PAGE 35
Crestron MPS-200 Multimedia Presentation System 200 Any program created for the MPS-200 with SystemBuilder will include the out-ofthe-box functionality in addition to any additional programming created with SystemBuilder. Programming with SIMPL Windows NOTE: While SIMPL Windows can be used to program the MPS-200, it is recommended to use SystemBuilder for configuring an MPS-200 system. SIMPL Windows is Crestron’s premier software for programming Crestron control systems.
PAGE 36
Multimedia Presentation System 200 Crestron MPS-200 The symbol can be viewed by double clicking on the icon or dragging it into Detail View. A description for each signal in the symbol is described in the SIMPL Windows help file (F1). Switching Programs If a custom program is loaded into the MPS-200, the MPS-200 will run the custom program when it boots up. To switch to the out-of-the-box program: 1. Press and release HW-R. 2.
PAGE 37
Crestron MPS-200 Multimedia Presentation System 200 Uploading and Upgrading Crestron recommends using the latest programming software and that each device contains the latest firmware to take advantage of the most recently released features. However, before attempting to upload or upgrade it is necessary to establish communication. Once communication has been established, files (for example, programs or firmware) can be transferred to the control system.
PAGE 38
Multimedia Presentation System 200 TCP/IP Communication Crestron MPS-200 Ethernet Communication PC RUNNING CRESTRON TOOLBOX MPS-200 ETHERNET • Establish USB communications between the MPS-200 and a PC. • Enter the IP address, IP mask and default router of the MPS-200 via the Crestron Toolbox (Functions | Ethernet Addressing); otherwise enable DHCP. • Confirm Ethernet connections between MPS-200 and PC.
PAGE 39
Crestron MPS-200 Multimedia Presentation System 200 Configuration & Operation The MPS-200 can be used for audio and video switching without any programming required. This is ideal for those that need a basic audio-video switching system. Prior to operation, the MPS-200 must be configured for use. Configuration The MPS-200 is configured using the built-in menu. Access the Menu To access the menu: • Press the MENU button.
PAGE 40
Multimedia Presentation System 200 Exit the Menu Crestron MPS-200 To exit the menu: • While in the main menu, press the MENU button to exit the menu. Exit Menu Prompt Exit Setup Menu? Yes No ⇒ Press the soft button labeled Yes to exit the menu or press the soft button labeled No to return to the menu. NOTE: The following sections describe configuration instructions when the MPS-200 is running the out-of-the-box program or if an administrator password was entered (while a custom program is running).
PAGE 41
Crestron MPS-200 Multimedia Presentation System 200 RECORD output settings, source input compensation, master startup volume, and microphones. • Video Setup: Contains controls for naming input sources, selecting input signal types (video inputs only), and naming output destinations.
PAGE 42
Multimedia Presentation System 200 • Crestron MPS-200 Press the k or j buttons until “Source Mix” is displayed on the LCD and press ENTER to open the Program Source Mix controls. Program Source Mix Controls Program Source Mix Aud. Only • Press the k or j buttons until the desired setting is displayed on the LCD. The current setting is indicated with an asterisk (*). The following settings are available: ⇒ Aud. Only: Sends the audio signal from the selected source to the PROGRAM output. ⇒ Mic.
PAGE 43
Crestron MPS-200 Multimedia Presentation System 200 NOTE: While adjusting the Program Bass level, the Program Volume level can be adjusted by turning the volume control clockwise to raise the volume, or counterclockwise to lower the volume. When adjusting the volume, the display will change to indicate the volume level. • Set the Program Treble Level Press MENU or ENTER to save changes and return to the previous screen.
PAGE 44
Multimedia Presentation System 200 Crestron MPS-200 Program Minimum Volume Control Prog. Min Volume 30% • Adjust the Program Minimum Volume level with the j and k buttons. Press the k button to increase the Program Minimum Volume level. Press the j button to lower the Program Minimum Volume level. The highest Program Minimum Volume setting is 30%.
PAGE 45
Crestron MPS-200 Multimedia Presentation System 200 NOTE: While adjusting the Program Maximum Volume level, the Program Volume level can be adjusted by turning the volume control clockwise to raise the volume, or counterclockwise to lower the volume. When adjusting the volume, the display will change to indicate the volume level. • Set the Stereo / Mono Mode Press MENU or ENTER to save changes and return to the previous screen. The Stereo / Mono controls are used to set the PROGRAM output mode.
PAGE 46
Multimedia Presentation System 200 • Crestron MPS-200 Press the k or j buttons until “Startup Vol.” is displayed on the LCD and press ENTER to open the Program Startup Volume control. Program Startup Volume Control Prog. Startup Vol. 30% • Adjust the Program Startup Volume level with the j and k buttons. Press the k button to increase the startup volume level. Press the j button to lower the startup volume level. The highest Program Startup Volume setting is 100%.
PAGE 47
Crestron MPS-200 Multimedia Presentation System 200 press ENTER to open the Speech Source Mix controls. Speech Source Mix Controls Speech Source Mix Aud. Only • Press the k or j buttons until the desired setting is displayed on the LCD. The current setting is indicated with an asterisk (*). The following settings are available: ⇒ Aud. Only: Sends the audio signal from the selected source to the SPEECH output. ⇒ Mic. Only: Sends the microphone input signals to the SPEECH output.
PAGE 48
Multimedia Presentation System 200 Crestron MPS-200 NOTE: While adjusting the Speech Bass level, the Speech Volume level can be adjusted by turning the volume control clockwise to raise the volume, or counterclockwise to lower the volume. When adjusting the volume, the display will change to indicate the volume level. • Set the Speech Treble Level Press MENU or ENTER to save changes and return to the previous screen.
PAGE 49
Crestron MPS-200 Multimedia Presentation System 200 Speech Delay Control Speech Delay 0ms • Adjust the Speech Delay with the j and k buttons. Press the k button to increase the delay. Press the j button to lower the delay. The highest delay setting is 40 milliseconds. NOTE: While adjusting the Speech Delay, the Speech Volume level can be adjusted by turning the volume control clockwise to raise the volume, or counterclockwise to lower the volume.
PAGE 50
Multimedia Presentation System 200 Crestron MPS-200 ⇒ Pgm/Spch Sel.: The front panel volume control will allow the user to select during operation if the knob affects the volume of PROG OUT or SPEECH OUT. ⇒ Master Vol.: The front panel volume control will control the master volume level, raising both the PROG OUT and SPEECH OUT volumes simultaneously while retaining their current proportional levels.
PAGE 51
Crestron MPS-200 Multimedia Presentation System 200 • Set the Speech Minimum Volume Set the Master Startup Volume to the desired level (will probably be less than 50%). Refer to the instructions on page 52. The Speech Minimum Volume control is used to set the lowest volume setting of the SPEECH output. The RECORD and PROGRAM outputs are not affected by changes made to the Speech Minimum Volume level. To set the Speech Minimum Volume level: • Access the Speech Output menu as described on page 42.
PAGE 52
Multimedia Presentation System 200 Crestron MPS-200 Speech Maximum Volume Control Spch. Max Volume 75% • Adjust the Speech Maximum Volume level with the j and k buttons. Press the k button to increase the Speech Maximum Volume level. Press the j button to lower the Speech Maximum Volume level. The lowest Speech Maximum Volume setting is 50%.
PAGE 53
Crestron MPS-200 Multimedia Presentation System 200 NOTE: While adjusting the Speech Startup Volume level, the Speech Volume level can be adjusted by turning the volume control clockwise to raise the volume, or counterclockwise to lower the volume. When adjusting the volume, the display will change to indicate the volume level. • Press MENU or ENTER to save changes and return to the previous screen.
PAGE 54
Multimedia Presentation System 200 • Crestron MPS-200 Press the k or j buttons until the desired setting is displayed on the LCD. The current setting is indicated with an asterisk (*). The following settings are available: ⇒ Aud. Only: Sends the audio signal from the selected source to the RECORD output. ⇒ Mic. Only: Sends the microphone input signals to the RECORD output. ⇒ Mic + Aud: Sends a mix of the audio signal from the selected source and the microphone input signals to the RECORD output.
PAGE 55
Crestron MPS-200 Adjust the Record Startup Volume Multimedia Presentation System 200 The Record Startup Volume control is used to establish the RECORD output’s volume level setting when an input is selected. The SPEECH and PROGRAM outputs are not affected by changes made to the Record Startup Volume level. NOTE: The Record Volume can only be used if the Fixed/Variable Mode is set to "Variable". For more information, refer to “Set Fixed/Variable Mode on page 50.
PAGE 56
Multimedia Presentation System 200 Crestron MPS-200 Select Input to Compensate Input Compensation Input 1 Comp. • To select the input to compensate, press the k or j buttons until the desired input is displayed and press ENTER. Adjust Compensation Level Input 1 Comp. 0db • Adjust the compensation level with the j and k buttons. Press the k button to increase the compensation level. Press the j button to lower the compensation level. Compensation can range from -10db to 10db.
PAGE 57
Crestron MPS-200 Multimedia Presentation System 200 Master Startup Volume Control Master Startup Vol. 30% • Adjust the Master Startup Volume level with the j and k buttons. Press the k button to increase the Master Startup Volume level. Press the j button to lower the Master Startup Volume level. The highest Master Startup Volume setting is 100%.
PAGE 58
Multimedia Presentation System 200 Crestron MPS-200 Microphone Gating Control (MIC 1 shown) Mic 1 Gating OFF • Press the k or j buttons until the desired setting is displayed on the LCD and press ENTER to save the setting. The current setting is indicated with an asterisk (*). The following settings are available: ⇒ OFF: The gating function for the selected microphone input is disabled. ⇒ ON: The gating function for the selected microphone input is enabled.
PAGE 59
Crestron MPS-200 Multimedia Presentation System 200 • Press the k or j buttons until “Mic 1 Gain” or “Mic 2 Gain” is displayed on the LCD and press ENTER to open the Microphone Gain control. Microphone Gain Control (MIC 1 shown) Mic 1 Gain 0% • Press the k or j buttons until the desired setting is displayed on the LCD and press ENTER to save the setting. • To exit the Microphone Gain control without saving changes, press MENU.
PAGE 60
Multimedia Presentation System 200 Crestron MPS-200 Name the Input BNC 1_ DEL Select Input Type INS < > • Turn the volume control clockwise or counterclockwise (or press the k or j buttons) to select a new letter (uppercase or lowercase) or number. Move the cursor by pressing the soft buttons labeled < or >. Each input name can be up to 14 characters in length. To delete a character, position the cursor under the character to be deleted and press the soft button labeled DEL.
PAGE 61
Crestron MPS-200 Multimedia Presentation System 200 Select Input Type Select Input 1 Type * Composite Name Video Outputs • Press ENTER to save the input type and return to the Select Input Type menu or press MENU to cancel the operation and return to the Select Input Type menu. • After all inputs have been configured, press MENU to return to the Video Setup menu. The MPS-200 ships with default names assigned to each of the outputs. Output 1 is called “PROJECTOR”. Output 2 is called “TOUCHPANEL”.
PAGE 62
Multimedia Presentation System 200 Crestron MPS-200 • Turn the volume control clockwise or counterclockwise (or press the k or j buttons) to select a new letter (uppercase or lowercase) or number. Move the cursor by pressing the soft buttons labeled < or >. Each output name can be up to 14 characters in length. To delete a character, position the cursor under the character to be deleted and press the soft button labeled DEL.
PAGE 63
Crestron MPS-200 Set the Subnet Mask Multimedia Presentation System 200 • Press ENTER to move the cursor to the next section of the address. To change a different section, press the soft button under the section to be changed. • Repeat the previous two steps until the entire IP address is set. • To save the new address and return to the Network Setup menu, move the cursor to the right-most section and press ENTER. To cancel the operation and return to the Network Setup menu, press MENU.
PAGE 64
Multimedia Presentation System 200 Crestron MPS-200 Display the Default Router Address Def. Router [000] Set the DHCP Mode 000. 000. 000 • Turn the volume control clockwise or counterclockwise to select a number. You can also press the k or j buttons to select a number. • Press ENTER to move the cursor to the next section of the address. To change a different section, press the soft button under the section to be changed.
PAGE 65
Crestron MPS-200 Set the WINS Mode Multimedia Presentation System 200 The MPS-200 can use a WINS server to obtain an IP address. To set the WINS mode: • Access the Network Setup menu as described on page 58. • Press the k or j buttons until “WINS” is displayed on the LCD and press ENTER button to display the WINS controls. Display the WINS Mode WINS On View and Set the Hostname • Press the k and j buttons to toggle between On and Off. The current setting is indicated with an asterisk (*).
PAGE 66
Multimedia Presentation System 200 Crestron MPS-200 Change the Hostname MPS-200-00107EA0122_ DEL View and Set the Domain Name INS < > • Turn the volume control clockwise or counterclockwise (or press the k or j buttons) to select a new letter (uppercase or lowercase) or number. Move the cursor by pressing the soft buttons labeled < or >. The Hostname can be up to 64 characters in length.
PAGE 67
Crestron MPS-200 Multimedia Presentation System 200 Change the Domain Name corporate.company.c DEL Set the RoomView Mode INS < > • Turn the volume control clockwise or counterclockwise (or press the k or j buttons) to select a new letter (uppercase or lowercase) or number. Move the cursor by pressing the soft buttons labeled < or >. The Domain name can be up to 64 characters in length.
PAGE 68
Multimedia Presentation System 200 Display the MAC Address Crestron MPS-200 The MPS-200 can display its MAC address. To view the MAC address: • Access the Network Setup menu as described on page 58. • Press the k or j buttons until “MAC Address” is displayed on the LCD and press ENTER to display the MAC address. • Press MENU to return to the Network Setup menu. Control Setup Basic control system operations can be performed from the MPS-200 front panel using the Control Setup menu.
PAGE 69
Crestron MPS-200 Multimedia Presentation System 200 Select Function to Name Select Fct. To Name 1:MUTE • Press the k or j buttons until the function to be named is displayed on the LCD and press ENTER. The cursor is placed after the last character in the function name. Name the Function MUTE_ DEL Identify Network Devices Operations Guide – DOC.
PAGE 70
Multimedia Presentation System 200 Crestron MPS-200 ID Devices Prompt Press ENTER to ID all devices. • Press ENTER to continue the identification process, the MPS-200 will clear all device settings and prompt the user to select the device type to be identified. Select Device Type Select device type APAD • Press the k or j buttons until the device type to be identified is displayed on the LCD and press ENTER. The buttons (or SETUP LEDs) of the selected device type will flash.
PAGE 71
Crestron MPS-200 Multimedia Presentation System 200 Display the APAD Upgrade Controls Upgrade APAD Yes Change the Front Panel Password • To upgrade the APAD, press the k or j buttons until “Yes” is displayed on the LCD and press ENTER. The MPS-200 will upgrade the APAD’s firmware (if necessary) and copy the required files to the APAD. • To cancel the upgrade procedure without starting the upgrade process, press the k or j buttons until “No” is displayed on the LCD and press ENTER.
PAGE 72
Multimedia Presentation System 200 Crestron MPS-200 NOTE: This information can be viewed using Crestron Toolbox. For more information, refer to the Crestron Toolbox help file. • Access the Control Setup menu as described on page 64. • Press the k or j buttons until “Info” is displayed on the LCD and press ENTER to display the Info menu. Display the Info Menu Info REMS • HW NET OPS To view program information, press the soft button labeled REMS.
PAGE 73
Crestron MPS-200 Multimedia Presentation System 200 ⇒ Press the MENU button to return to the Info menu. • To view a list of connected network devices, press the soft button labeled NET. Display Connected Network Devices 2E: APAD LCD 6-bu << >> ⇒ Press the k or j buttons to see other network devices. If the information for a network device is partially displayed, press the soft buttons labeled << or >> to view the rest of the information. ⇒ Press the MENU button to return to the Info menu.
PAGE 74
Multimedia Presentation System 200 Crestron MPS-200 Display the Message Controls System log: Top Clear << >> • To scroll through messages in the log, press the k or j buttons. • To jump to the beginning of the log, press the soft button labeled Top. • To jump to the last message in the long, press the soft button labeled Btm (not shown). • To view the contents of a message press the soft buttons labeled << or >>. • To erase the contents of the log, press the soft button labeled Clear.
PAGE 75
Crestron MPS-200 Multimedia Presentation System 200 Display the Date Controls DATE: 10/16/2006 MO DAY YR ⇒ To set the month, press the soft button labeled MO. To set the day, press the soft button labeled DAY. To set the year, press the soft button labeled YR. A pair of brackets will appear around the selected part of the date. ⇒ Press the k or j buttons to increase or decrease the value of the selected part of the date. ⇒ Repeat for each part of the date.
PAGE 76
Multimedia Presentation System 200 Restore Default Settings Crestron MPS-200 The MPS-200 can be restored to its default factory settings from the front panel. Users can select to restore the audio settings or to restore the audio settings, source names, output names, and function names. • To restore audio settings only: ⇒ Access the Control Setup menu as described on page 64. ⇒ Press the k or j buttons until “Defaults” is displayed on the LCD and press ENTER to display the Restore Defaults menu.
PAGE 77
Crestron MPS-200 Multimedia Presentation System 200 Restore Defaults Menu-All Settings Restore Defaults All settings ⇒ Press the k or j buttons until “All settings” is displayed on the LCD and press ENTER. Confirm Restore All Default Settings Only Reset all settings? No ⇒ Press the k or j buttons until “Yes” is displayed on the LCD and press ENTER to restore the audio settings, source names, output names, and function names to the factory defaults.
PAGE 78
Multimedia Presentation System 200 • Crestron MPS-200 Press the k or j buttons until “Front Panel” is displayed on the LCD and press ENTER to display the Front Panel control. Front Panel Lock Controls Front Panel Lock: On • Press the k or j buttons to toggle between On and Off. The current setting is indicated with an asterisk (*). • Press ENTER to save the new setting and return to the Control Setup menu.
PAGE 79
Crestron MPS-200 Lower the Projection Screen Multimedia Presentation System 200 Press the function button labeled SCREEN DOWN to lower the projector screen. NOTE: This function will only work if a projection screen’s control lines have been connected to RELAY 1 (up control) and RELAY 2 (down control). Raise the Projection Screen Press the button labeled SCREEN UP to raise the projector screen.
PAGE 80
Multimedia Presentation System 200 • Mute Audio Adjust Lighting Crestron MPS-200 Lower the volume: Turn the volume control counterclockwise. The volume level will be displayed on the LCD. The audio output of the MPS-200 can be muted with the MUTE button. • Mute the audio output: Press the button labeled MUTE. • Unmute the audio output: Press the MUTE button again. To set lighting to one of two preset lighting values, press either LIGHTS PRE 1 or LIGHTS PRE 2.
PAGE 81
Crestron MPS-200 Turn On the System Multimedia Presentation System 200 To turn on the system: 1. Press the soft button labeled Source to display a list of available sources. 2. Turn the Nav Wheel to highlight the desired source (BNC 1, BNC 2, BNC 3, BNC 4, RGBHV 5, RGBHV 6, RGBHV 7, or RGBHV 8). NOTE: Typically, signal routing information is not displayed on the front panel of the MPS-200.
PAGE 82
Multimedia Presentation System 200 Mute Audio Crestron MPS-200 The audio output of the MPS-200 can be muted with the APAD. • To Mute the audio output: ⇒ Press the power button ⇒ Press the soft button labeled Mute. The display will indicate that the audio output is muted. The front panel of the MPS-200 will indicate the status of the mute function. • To Unmute the audio output: ⇒ Press the soft button labeled Unmute. Adjust Lighting To set lighting to one of two preset lighting values: 1.
PAGE 83
Crestron MPS-200 Multimedia Presentation System 200 NOTE: Buttons for the keypad are custom engraved using Crestron SystemBuilder software. For instructions on installing the buttons on the keypad, refer to the keypad’s guide. The keypad has twelve buttons as shown in the following diagram. C2N-DB12 Buttons BNC 1 POWER BNC 2 BNC 3 BNC 4 RGBHV 5 RGBHV 6 MUTE RGBHV 7 VOL UP RGBHV 8 VOL DOWN NOTE: Custom buttons can be created using Crestron Engraver software.
PAGE 84
Multimedia Presentation System 200 Crestron MPS-200 NOTE: Buttons for the keypad are custom engraved using Crestron SystemBuilder software. For instructions on installing the buttons on the control center, refer to the control center’s guide. The control center has 10 buttons as shown in the following diagram.
PAGE 85
Crestron MPS-200 Multimedia Presentation System 200 Mute Audio To mute the audio output, press the MUTE button. To unmute, press the MUTE button again. The front panel of the MPS-200 will indicate the status of the mute function. Adjust Lighting To toggle between preset light settings, press either of the LIGHTS buttons. The front panel of the MPS-200 will indicate the selected preset light setting.
PAGE 86
Multimedia Presentation System 200 Crestron MPS-200 Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. MPS-200 Troubleshooting TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION Unexpected response from control system. Network devices are not communicating with the control system. Use Crestron Toolbox to poll the network.
PAGE 87
Crestron MPS-200 Multimedia Presentation System 200 NOTE: If communication cannot be established or the control system is locked-up, refer to “Troubleshooting Communications” in the Crestron 2-Series Control Systems Reference Guide (Doc. 6256). NOTE: Passthrough Mode enables Viewport access to any serial controlled device on the network. This aids in troubleshooting by allowing direct communication between the PC and a network device (effectively “passing through” the MPS-200).
PAGE 88
Multimedia Presentation System 200 Crestron MPS-200 Make sure to choose USB as the “Connection Type”, then click OK. The following text will appear in the bottom right corner of the “Text Console” window: usb;device 2SeriesCtrlSystemMonitor The following text will appear in Toolbox: MPSMNTR> 10. At the Toolbox prompt, type erase and press Enter. The following text will appear in Toolbox: Erasing ->25%->50%->75%->100% Done icon and select Firmware… to open the “Firmware” 11.
PAGE 89
Crestron MPS-200 Calculate Power Multimedia Presentation System 200 CAUTION: Use only Crestron power supplies for Crestron equipment. Failure to do so could cause equipment damage or void the Crestron warranty. CAUTION: Provide sufficient power to the system. Insufficient power can lead to unpredictable results or damage to the equipment. Please use the Crestron Power Calculator to help calculate how much power is needed for the system (http://www.crestron.com/calculators).
PAGE 90
Multimedia Presentation System 200 Crestron MPS-200 List of Related Reference Documents DOCUMENT TITLE 2-Series Control Systems Reference Guide APAD Wall Mount LCD Controller C2N-ANLZ Cresnet Analyzer C2N-DB12 12-Button Decorator Function Keypads CNX-B12 12-Button Designer Keypads C2N-FTB FlipTop Control Center C2N-MNETGW infiNET Gateway/Transceiver CAT5 Wiring Reference Guide CLS-C6 iLux Integrated Lighting System Crestron e-Control Reference Guide QM-AMP Three Channel Amplifier MediaManager Application
PAGE 91
Crestron MPS-200 Multimedia Presentation System 200 Software License Agreement This License Agreement (“Agreement”) is a legal contract between you (either an individual or a single business entity) and Crestron Electronics, Inc. (“Crestron”) for software referenced in this guide, which includes computer software and as applicable, associated media, printed materials and “online” or electronic documentation (the “Software”).
PAGE 92
Multimedia Presentation System 200 Crestron MPS-200 If You are a business or organization, You agree that upon request from Crestron or its authorized agent, You will within thirty (30) days fully document and certify that use of any and all Software at the time of the request is in conformity with Your valid licenses from Crestron of its authorized agent.
PAGE 93
Crestron MPS-200 Multimedia Presentation System 200 Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact an authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory and request an RMA (Return Merchandise Authorization) number.
PAGE 94
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations Guide – DOC. 6528B (2016140) 10.07 Specifications subject to change without notice.