Specifications
Maestro
tm
Phone 425-775-8461 • Fax 425-778-3166
®
Configuration
Section 3-3
Basic Setup Menus
1. General Settings
VV
VV
V
olume Displayolume Display
olume Displayolume Display
olume Display – This controls how the system volume is
displayed on the front panel and On-Screen Display (OSD).
There are three options:
NorNor
NorNor
Nor
malmal
malmal
mal 0 to 72 (in 1 dB steps),
FF
FF
F
ineine
ineine
ine –72 to 0 (0.5 dB steps) and
THX RefTHX Ref
THX RefTHX Ref
THX Ref –53 to +18 (in 1
dB steps). We recommend the THX Reference mode. This
displays a level relative to the THX nominal level of 0 dB.
This 0 dB reference level is the same as a commercial movie
theater in a properly calibrated system.
Max VMax V
Max VMax V
Max V
olumeolume
olumeolume
olume – This sets the highest volume that you can
set the Maestro to. This is useful if you have speakers or
amplifiers of limited power handling abilities.
Max On VMax On V
Max On VMax On V
Max On V
olumeolume
olumeolume
olume – This is the highest volume that the
Maestro will power on at. This prevents the Maestro from
being turned on at shock volume levels from the last time
you were watching a good movie.
Delay UnitsDelay Units
Delay UnitsDelay Units
Delay Units – The settings can be adjusted in
EnglishEnglish
EnglishEnglish
English
(Inches),
MetricMetric
MetricMetric
Metric (Centimeters), or
TT
TT
T
imeime
imeime
ime (milliseconds).
Important Installation Note:Important Installation Note:
Important Installation Note:Important Installation Note:
Important Installation Note: When you change the Delay
Units, all delay settings are returned to “0”. Make certain
you choose your preferred units BEFORE adjusting the
delays.
OSD ModeOSD Mode
OSD ModeOSD Mode
OSD Mode – The On-Screen Display (OSD) can be dis-
played in either
MixMix
MixMix
Mix
eded
eded
ed mode where the white text is
overlaid onto the video image, or in
FF
FF
F
ull Pull P
ull Pull P
ull P
ageage
ageage
age mode where
the video image is temporarily replaced with a black back-
ground.
VV
VV
V
ideo Statusideo Status
ideo Statusideo Status
ideo Status – This sets the operation of the 12 volt trigger
outputs. For normal operation, leave this set to
ScreenScreen
ScreenScreen
Screen
ControlControl
ControlControl
Control. This enables the Main and Video Trigger outputs
to operate for equipment control triggers. The
SCSC
SCSC
SC
ARAR
ARAR
AR
TT
TT
T
option is only used on European video equipment to
control external video switching and scan-rate converters.
HQ VHQ V
HQ VHQ V
HQ V
ideoideo
ideoideo
ideo – Choose the operation of the OSD to match
your video projector or display. Typical high-end video
systems use Component Video (Y, PB, PR) for their signals.
Don’t confuse the colors on the RCA cables used to connect
the video equipment with the format. Many Component
video cables have their connectors colored red, green and
1 - General Settings
Volume Display: Normal 0-72
Max Volume: +72
Max On Volume: +20
Delay units: English
OSD Mode: Mixed
Video Status: CNTL
HQ Video: Comp
Note: The On-Screen Display
will automatically switch to
full page mode when the video
signal scan rate is higher than
normal interlaced video (i.e.
Progressive or HDTV).