User`s manual

MP-1xx/H.323
MP-1xx/H.323 User’s Manual 64 Document #: LTRT-00651
Table 6-3: H.323 Parameters (continues on pages 59 to 67)
ini File Field Name
GUI Parameter Name
*
Valid Range and Description
IsSpecialDigits
0 = not used (Default)
1 = Allows user to dial “*” and “#”, and allows endpoint telephone number to contain such
digits.
Notes:
a. When this feature is activated, “#” can’t be used to end the dialed number.
b. # and * can be used as first digit of dialed number, disregard the value of
"IsSpecialDigits" parameter.
IsFSOpenMediaOn
Connect
0 = Voice channel is open after sending an Alert message (default)
1 = Voice channel is opened after sending a Connect message
After receiving Setup message the Gateway can open voice channel immediately, or it
can wait until the call is answered and Connect message is sent.
Note that this is only relevant if Fast Start or Tunneling are used.
IsFSMediaInfoSendOn
Connect
0 = Fast Start Structure response is send in Alert message (default)
1 = Fast Start Structure response is send in Connect message
After receiving Fast Start Setup message, Gateway should reply with H.225 message
that includes media information structure. It can be send with Alert or Connect
messages. Sending this information in Alert message enables the remote side to open
the voice channel before receiving the Connect message.
Note that this is only relevant if Fast Start is used.
IsFSRemoteRBTone
0 = Originator of Fast Start call plays local ringback tone, until it receives Connect
message (default)
1 = If the received Alert message contains media information structure, the Gateway
opens voice channel, without playing any local tone to the channel. It is the remote
Gateway’s responsibility to play the ringback tone over IP.
If the Alert message doesn’t contain media information structure, the voice channel is not
opened and a local ringback tone is generated, until Connect message is received.
Note that this is only relevant if Fast Start is used.
PlayRBTone2Tel
0 – Don't play for fast start
1 – Play
2 – Play according to Progress Indicator (PI). The Gateway will not play local ringback
tone if PI=1 or PI=8 was received in H.225 Alert message. (default)
PlayRBTone2IP
0 – Don't play Ringback to to IP (default)
1- Play Ringback tone to IP, and set PI=8 in H,225 Alert message
ProgressIndicator2IP
0 – No PI will be send in H.225 messages
1- PI = 1 will be send to IP in H.225 Alert
8 - PI = 8 will be send to IP in H.225 Alert
If not configured at all (default) the PI send in H.225 messages will be set according to
"Play Ringback tone to IP" parameter.
CallerDisplayInfo#
(Caller ID table)
Caller DisplayInfo table is used to send Caller Identification information per FXS Gateway
port to remote IP terminal.
This parameter can appear up to eight times (for MP-10x), with up to 18 characters per
string. For MP-124 the parameter can appear up to 24 times, with up to 10 characters
per string.
For example:
CallerDisplayInfo0 = AudioCodes 1001
CallerDisplayInfo1 = AudioCodes 1002
;
;
CallerDisplayInfo8 = AudioCodes 1008
EnableCallerID
(Enable Caller ID)
0 = Don’t send CallerID signal to Gateway’s FXS port (default)
1 = Calling number and Display text is sent to Gateway FXS port, between first and
second rings, to be displayed on phone’s caller ID display for incoming call.
In FXO Gateway if "EnableCallerID=1", the Caller ID signal will be detected and send to
IP in H.323 Setup message (as "Display" element).
H225ListenPort
(H.225 Listen Port)
H.225 TCP listen port (default 1720)
Gateway expects to receive H.225/Setup message on this port
H225DialPort
(H.225 Dial Port)
H.225 TCP destination port (default 1720)
Gateway sends H.225/Setup message to this port