User`s manual

MP-1xx/H.323 User’s Manual 6. Provisioning
Version 4.2 Beta 63 June 2003
Table 6-3: H.323 Parameters (continues on pages 59 to 67)
ini File Field Name
GUI Parameter Name
*
Valid Range and Description
IsWaitForDialTone
0 = don’t wait for dial tone
1 = Wait for dial tone (default)
Used for MP-1xx/FXO, for ‘One Stage Dialing’.
If IsWaitForDialTone = 0, MP-10x/FXO dials phone number immediately after seizing the
PSTN/PBX line, without ‘listening’ to dial tone.
If IsWaitForDialTone = 1, MP-10x/FXO dials phone number only after it detects a dial
tone (it can take 3-5 sec to detect a dial tone).
The correct dial tone parameters should be configured in call progress tone file.
FXOWaitForDialTime
FXO dialing timeout [in msec] , after seizing the line and before start dialing. (Default
=1000)
Applicable for MP-10x FXO for single stage dialing.
EnableSilenceDisconnect
If enabled, the FXO Gateway will disconnect call if silence is detected for 120 seconds
(default)
FarEndDisconnectPeriod
Duration of Silence period [in seconds] for call disconnection. (Default = 120)
Applicable for FXO Gateway, that are using DSP template = 3 or 4.
MaxDigits
(Max Digits in Phone
number)
2 to 19 (default 4). Maximum number of digits that can be dialed.
Dialing ends when maximum number of digits dialed or timeout between digits expired
(TimeBetweenDigits parameter), or ‘#’ is dialed.
TimeBetweenDigits
(Interdigit Timeout [sec])
0 to 5 (default
4) Inter-digit timeout in seconds, used to terminate dialed numbers.
IsSETUPIncludeNum
(Does Setup Include Phone
Number)
0 = Send empty SETUP (or GK ARQ) message, without called party number.
1 – Don’t send empty setup message (default)
DefaultNumber
(Default Destination
Number)
Phone number
Gateway Dial to this number if SETUP received with no phone number. Must be one of
the phone numbers of the end points.
EnableQ931Cause
0 – H.225 Release reason will be send in Release Complete H.323 message
1 – Q.931 cause will be send in Release Complete message (default)
IsSetupAckUsed
(Release Call on “Setup
ACK”)
0 = On receiving of Setup Ack message, Gateway releases the Call (default)
1 = On receiving of Setup Ack message the call is not released.
When working in non-overlap mode (‘IsOverlapUsed = 0’), use this parameter to enable
receiving of Setup Ack messages.
This parameter is used for specific, non-standard applications. Usually when working in
non-overlap mode Setup Ack messages are not sent.
OpenH245onFS
0 = Don’t open H.245 channel of Fast Start (default)
1 = H.245 channel is opened immediately after Fast Start connection is established.
Opening of H.245 channel may be needed for relaying DTMF digits over H.245 channel,
during a call.
IsDTMFUsed
(Enable DTMF over H.245)
0 = not used (default)
1 = DTMF digits are sent over H.245 channel using Facility message
Incoming facility messages of out-of-band DTMF is played into FXS or FXO channels.
For using out of band DTMF the User must disable inband DTMF by setting:
‘DTMFTransportType = 0’ (erase digit and don’t relay).
Note that this feature is not supported when using Fast Start, unless other party opens
H.245 channel.
IsHookFlashUsed
(Enable Hook-Flash)
0 = not used (default)
1 = Send H.245 User Input Indication message, when hookflash is detected
Received facility message with HookFlash signal generates HookFlash at FXO channel
Is931MsgUsed
(Send DTMF over
H.225/Q.931)
0 = not used (default)
1 = DTMF digits and HookFlash signal is sent in H.225/Q.931 info message (keypad
facility)
Note that incoming Q.931 DTMF digits and HookFlash are always ignored.
To use H.225/Q.931 messages, set the following params:
‘IsDTMFUsed = 0’ and ‘IsOverlapUsed = 0’