User`s manual

MP-1xx/H.323
MP-1xx/H.323 User’s Manual 60 Document #: LTRT-00651
Table 6-3: H.323 Parameters (continues on pages 59 to 67)
ini File Field Name
GUI Parameter Name
*
Valid Range and Description
CanMapAliases
(Enable Mapping of Alias
Numbers)
If enabled, GK can change Gateway destination number, using Alias parameter in ACF
message.
IsAutoDiscovery
0 = no auto discovery of Gatekeeper (default)
Gatekeeper Auto Discovery requires multicast and is not supported
IsTerminal
0 = Standard Gateway behavior (default)
1 = Gateway imitates an H.323 terminal with multiple aliases (up to 24 for MP-124).
In all Gateway messages the “terminal type” value is set to “terminal”
IsTunnelingUsed
0 = no tunneling (default)
1 = tunneling
EnableRAI
0 – Disable RAI messages
1 – RAI message with almost out of resources will be send to GK if GW resources are
below the threshold.
Usually RAI will be applicable if Gateway is configured to use Hunt groups.
RAIHighThreshold
0-100, "Out of resources" Gateway threshold, in percentage [default = 90%]
When number of GW busy endpoints [%} is above the High Threshold, GW will send RAI
message with "almostOutOfResources = TRUE "
GW Resources [%] is calculated as number of busy endpoints divided by total available
GW endpoinrs.
RAILowThreshold
0-100, "Out of resources" Gateway threshold, in percentage [default = 90%]
When number of GW busy endpoints [%] is below the LowThreshold, GW will send RAI
message with "almostOutOfResources = FALSE "
RAILoopTime
GW check for resource availability each RAILoopTime period [sec] (default 10sec)
IsFastConnectUsed
0 = normal connect (default)
1 – fast connect
CoderName
(Coders)
Coder name that is used.
g711Ulaw64k – G.711 µ-law, 20 msec
g711Alaw64k – G.711 A-law, 20 msec
g711Ulaw64k,5 – G.711 µ-law, 5 msec
g711Alaw64k,5 – G.711 A-law, 5 msec
g711Ulaw64k,10 – G.711 µ-law, 10 msec
g711Alaw64k,10 – G.711 A-law, 10 msec
g7231 – G.723 6.3 kbps (default)
g7231r53 – G.723 5.3 kbps
g726 – G.726 ADPCM 16 kbps (Payload Type = 35)
g726r16 – G.726 ADPCM 16 kbps, Cisco mode (PT=23)
g726r32 – G.726 ADPCM 32 kbps (PT=2)
g729 – G.729A , 20msec
g729,10 – G.729, 10msec
NetCoder6_4 – NetCoder 6.4 kbps
NetCoder7_2 – NetCoder 7.2 kbps
NetCoder8 – NetCoder 8.0 kbps
NetCoder8_8 – NetCoder 8.8 kbps
This parameter can appear up to 5 times.
ChannelList List of phone numbers for MP-1xx channels
a, b, c
a = first channel
b = number of channels starting from “a”
c = the phone number of the first channel
example: ChannelList = 0,8,101
Defines phone numbers 101 to 108 for up to 8 MP-108 channels.
The ini file can include up to ten “ChannelList = “ entries
The “ChannelList = “ can be used instead or in addition to Channel2Phone parameter.