User`s manual

MediaPack SIP User’s Manual 5. Configuring the MediaPack
Version 4.6 137 June 2005
Table 5-41: Channel Settings, Fax/Modem/CID Parameters (continues on pages 136 to 138)
Parameter Description
Caller ID Type
[CallerIDType]
Defines one of the following standards for detection (FXO) and generation (FXS)
of Caller ID and detection (FXO) of MWI (when specified) signals.
Bellcore [0] (Caller ID and MWI) (default).
ETSI [1] (Caller ID and MWI)
NTT [2].
British [4]
DTMF ETSI [16]
Denmark [17] (Caller ID and MWI)
India [18]
Brazil [19]
Note 1: The Caller ID signals are generated/detected between the first and the
second rings.
Note 2: To select the Bellcore Caller ID sub standard, use the parameter
‘BellcoreCallerIDTypeOneSubStandard’. To select the ETSI Caller ID sub
standard, use the parameter ‘ETSICallerIDTypeOneSubStandard’.
Note 3: To select the Bellcore MWI sub standard, use the parameter
‘BellcoreVMWITypeOneStandard’. To select the ETSI MWI sub standard, use the
parameter ‘ETSIVMWITypeOneStandard’.
V.21 Modem Transport Type
[V21ModemTransportType]
N/A.
V.22 Modem Transport Type
[V22ModemTransportType]
V.22 Modem Transport Type that the gateway uses.
You can select:
Transparent [0].
Relay [1] = N/A.
Bypass [2] (default).
V.23 Modem Transport Type
[V23ModemTransportType]
V.23 Modem Transport Type that the gateway uses.
You can select:
Transparent [0].
Relay [1] = N/A.
Bypass [2] (default).
V.32 Modem Transport Type
[V32ModemTransportType]
V.32 Modem Transport Type that the gateway uses.
You can select:
Transparent [0].
Relay [1] = N/A.
Bypass [2] (default).
Note: This option applies to V.32 and V.32bis modems.
V.34 Modem Transport Type
[V34ModemTransportType]
V.90 / V.34 Modem Transport Type that the gateway uses.
You can select:
Transparent [0].
Relay [1] = N/A.
Bypass [2] (default).
Fax Relay Redundancy Depth
[FaxRelayRedundancyDepth]
Number of times that each fax relay payload is retransmitted to the network.
The valid range is 0 to 2.
The default value is 0.
Fax Relay Enhanced Redundancy
Depth
[FaxRelayEnhancedRedundancyD
epth]
Number of times that control packets are retransmitted when using the T.38
standard.
The valid range is 0 to 4.
The default value is 2.
Fax Relay ECM Enable
[FaxRelayECMEnable]
Disable [0] = Error Correction Mode (ECM) mode is not used during fax relay.
Enable [1] = ECM mode is used during fax relay (default).
Fax Relay Max Rate (bps)
[FaxRelayMaxRate]
Maximum rate, in bps, at which fax relay messages are transmitted.
You can select:
2400 [0] = 2.4 kbps.
4800 [1] = 4.8 kbps.
7200 [2] = 7.2 kbps.
9600 [3] = 9.6 kbps.
12000 [4] = 12.0 kbps.
14400 [5] = 14.4 kbps (default).