User`s manual
Table Of Contents
- Mediant 2000 & TP-1610 & TP-260/UNI SIP User’s Manual Version 5.0
- Table of Contents
- List of Figures
- List of Tables
- Notices
- 1. Overview
- 2. Physical Description
- 3. Installation
- 4. Getting Started
- 5. Web Management
- Computer Requirements
- Protection and Security Mechanisms
- Accessing the Embedded Web Server
- Getting Acquainted with the Web Interface
- Protocol Management
- Advanced Configuration
- Status & Diagnostic
- Software Update Menu
- Maintenance
- Logging Off the Embedded Web Server
- 6. Gateway's ini File Configuration
- Secured ini File
- Modifying an ini File
- The ini File Content
- The ini File Structure
- The ini File Example
- Networking Parameters
- System Parameters
- Web and Telnet Parameters
- Security Parameters
- RADIUS Parameters
- SNMP Parameters
- SIP Configuration Parameters
- Voice Mail Parameters
- ISDN and CAS Interworking-Related Parameters
- Number Manipulation and Routing Parameters
- E1/T1 Configuration Parameters
- Channel Parameters
- Configuration Files Parameters
- 7. Using BootP / DHCP
- 8. Telephony Capabilities
- Working with Supplementary Services
- Configuring the DTMF Transport Types
- Fax & Modem Transport Modes
- Event Notification using X-Detect Header
- ThroughPacket™
- Dynamic Jitter Buffer Operation
- Configuring the Gateway’s Alternative Routing (based on Conn
- Call Detail Report
- Supported RADIUS Attributes
- Trunk to Trunk Routing Example
- Proxy or Registrar Registration Example
- SIP Call Flow Example
- SIP Authentication Example
- 9. Networking Capabilities
- 10. Advanced PSTN Configuration
- 11. Advanced System Capabilities
- 12. Special Applications
- 13. Security
- 14. Diagnostics
- 15. SNMP-Based Management
- SNMP Standards and Objects
- Carrier Grade Alarm System
- Cold Start Trap
- Third-Party Performance Monitoring Measurements
- TrunkPack-VoP Series Supported MIBs
- Traps
- SNMP Interface Details
- SNMP Manager Backward Compatibility
- Dual Module Interface
- SNMP NAT Traversal
- SNMP Administrative State Control
- AudioCodes’ Element Management System
- 16. Configuration Files
- Appendix A. Selected Technical Specifications
- Appendix B. Supplied SIP Software Kit
- Appendix C. SIP Compliance Tables
- Appendix D. The BootP/TFTP Configuration Utility
- Appendix E. RTP/RTCP Payload Types and Port Allocation
- Appendix F. RTP Control Protocol Extended Reports (RTCP-XR)
- Appendix G. Accessory Programs and Tools
- Appendix H. Release Reason Mapping
- Appendix I. SNMP Traps
- Appendix J. Installation and Configuration of Apache HTTP Server
- Appendix K. Regulatory Information

SIP User's Manual 5. Web Management
Version 5.0 67 October 2006
5.5.3.1 Dialing Plan Notation
The dialing plan notation applies, in addition to the four Manipulation tables, also to TelÆIP
Routing table and to IPÆTrunk Group Routing table.
When entering a number in the destination and source ‘Prefix’ columns, you can create an
entry that represents multiple numbers using the following notation:
[n-m] represents a range of numbers
[n,m] represents multiple numbers. Note that this notation only supports single digit
numbers.
x represents any single digit
# (that terminates the number) represents the end of a number
A single asterisk (*) represents any number
For example:
[5551200-5551300]# represents all numbers from 5551200 to 5551300
[2,3,4]xxx# represents four-digit numbers that start with 2, 3 or 4
54324 represents any number that starts with 54324
54324xx# represents a 7 digit number that starts with 54324
123[100-200]# represents all numbers from 123100 to 123200.
The VoIP gateway matches the rules starting at the top of the table. For this reason, enter
more specific rules above more generic rules. For example, if you enter 551 in entry 1 and
55 in entry 2, the VoIP gateway applies rule 1 to numbers that starts with 551 and applies
rule 2 to numbers that start with 550, 552, 553, 554, 555, 556, 557, 558 and 559. However
if you enter 55 in entry 1 and 551 in entry 2, the VoIP gateway applies rule 1 to all numbers
that start with 55 including numbers that start with 551.
5.5.3.2 Numbering Plans and Type of Number
Numbers are classified by their Numbering Plan Indication (NPI) and their Type of Number
(TON). The gateway supports all NPI/TON classifications used in the standard. The list of
ISDN ETSI NPI/TON values is shown as follows:
Table 5-4: NPI/TON Values for ISDN ETSI
NPI TON Description
Unknown [0] Unknown [0]
A valid classification, but one that has no information
about the numbering plan.
Unknown [0]
A public number in E.164 format, but no information on
what kind of E.164 number.
International [1]
A public number in complete international E.164 format.
For example: 16135551234
National [2]
A public number in complete national E.164 format. For
example: 6135551234
E.164 Public [1]
Subscriber [4]
A public number in complete E.164 format representing a
local subscriber. For example: 5551234
Unknown [0]
A private number, but with no further information about the
numbering plan
Level 2 Regional [1]
Level 1 Regional [2] A private number with a location. For example: 3932200
PISN Specific [3]
Private [9]
Level 0 Regional (local) [4] A private local extension number. For example: 2200