User`s manual
Table Of Contents
- Mediant 2000 & TP-1610 & TP-260/UNI SIP User’s Manual Version 5.0
- Table of Contents
- List of Figures
- List of Tables
- Notices
- 1. Overview
- 2. Physical Description
- 3. Installation
- 4. Getting Started
- 5. Web Management
- Computer Requirements
- Protection and Security Mechanisms
- Accessing the Embedded Web Server
- Getting Acquainted with the Web Interface
- Protocol Management
- Advanced Configuration
- Status & Diagnostic
- Software Update Menu
- Maintenance
- Logging Off the Embedded Web Server
- 6. Gateway's ini File Configuration
- Secured ini File
- Modifying an ini File
- The ini File Content
- The ini File Structure
- The ini File Example
- Networking Parameters
- System Parameters
- Web and Telnet Parameters
- Security Parameters
- RADIUS Parameters
- SNMP Parameters
- SIP Configuration Parameters
- Voice Mail Parameters
- ISDN and CAS Interworking-Related Parameters
- Number Manipulation and Routing Parameters
- E1/T1 Configuration Parameters
- Channel Parameters
- Configuration Files Parameters
- 7. Using BootP / DHCP
- 8. Telephony Capabilities
- Working with Supplementary Services
- Configuring the DTMF Transport Types
- Fax & Modem Transport Modes
- Event Notification using X-Detect Header
- ThroughPacket™
- Dynamic Jitter Buffer Operation
- Configuring the Gateway’s Alternative Routing (based on Conn
- Call Detail Report
- Supported RADIUS Attributes
- Trunk to Trunk Routing Example
- Proxy or Registrar Registration Example
- SIP Call Flow Example
- SIP Authentication Example
- 9. Networking Capabilities
- 10. Advanced PSTN Configuration
- 11. Advanced System Capabilities
- 12. Special Applications
- 13. Security
- 14. Diagnostics
- 15. SNMP-Based Management
- SNMP Standards and Objects
- Carrier Grade Alarm System
- Cold Start Trap
- Third-Party Performance Monitoring Measurements
- TrunkPack-VoP Series Supported MIBs
- Traps
- SNMP Interface Details
- SNMP Manager Backward Compatibility
- Dual Module Interface
- SNMP NAT Traversal
- SNMP Administrative State Control
- AudioCodes’ Element Management System
- 16. Configuration Files
- Appendix A. Selected Technical Specifications
- Appendix B. Supplied SIP Software Kit
- Appendix C. SIP Compliance Tables
- Appendix D. The BootP/TFTP Configuration Utility
- Appendix E. RTP/RTCP Payload Types and Port Allocation
- Appendix F. RTP Control Protocol Extended Reports (RTCP-XR)
- Appendix G. Accessory Programs and Tools
- Appendix H. Release Reason Mapping
- Appendix I. SNMP Traps
- Appendix J. Installation and Configuration of Apache HTTP Server
- Appendix K. Regulatory Information
SIP User's Manual 3. Installation
Version 5.0 47 October 2006
3.3.3 Installing the TP-260
¾ To install the TP-260 board, take these 8 steps:
1. End all applications running in the PC.
2. Shut down the PC, turn off the power, and remove the PC's cover.
3. Choose an available PCI slot and remove its blank rear bracket.
4. Insert the TP-260 board into the chosen PCI slot. Ensure that the front panel (bracket)
of the TP-260 board fits correctly into the opening in the rear panel of the PC's
chassis. Also, check that the edge of the PCI retainer bracket fits correctly into the
PC’s PCI slot.
5. Secure the front panel of the TP-260 board into the chassis frame with a standard
screw. This also ensures chassis ground to the TP-260 board.
6. Replace and secure the PC's cover.
7. Power up the PC.
8. When using Windows
TM
operating systems, the PC prompts that new hardware has
been found. The driver for the TP-260 is found in the supplied software package
(260_UNSeries.inf).
Note that since the TP-260 PCI gateway operates independently and relies on the
host’s PCI only for its power, the driver is only used to prevent the Found new
Hardware Wizard to reappear each time the host PC restarts.
3.3.4 Cabling the TP-260
¾ To cable the TP-260, take these 2 steps:
1. Connect the TP-260 E1/T1 interfaces to your E1/T1 trunks by using the four supplied
TP-260 E1/T1 cable splitters (shown in Figure 3-11). Connect a splitter to each of the
four RJ-48 connectors labeled Trunks 1/5, 2/6, 3/7 and 4/8 on the TP-260 front panel.
Each splitter distributes each RJ-48 connector into two separate connectors (wired
according to Figure 2-7): the first connector (labeled 1/4) on each splitter supports
each of the first four trunks, the second connector (labeled 5/8) on each splitter
supports each of the last four trunks.
Note: The TP-260 E1/T1 cable splitter is part of the 8-span TP-260 product and is
PSTN certified. When using a non-AudioCodes E1/T1 cable splitter,
AudioCodes cannot guarantee compliance with PSTN homologations.
Figure 3-11: TP-260 E1/T1 Cable Splitter
2. Connect the TP-260 Ethernet connection, located on the front panel, directly to the
network using a standard RJ-45 Ethernet cable. The Ethernet connector is wired
according to Figure 2-6.
Note that when assigning an IP address to the TP-260 using HTTP (under Step 1 in
Section 4.2.1), you may be required to disconnect this cable and re-cable it differently.