User`s manual
Table Of Contents
- Mediant 2000 & TP-1610 & TP-260/UNI SIP User’s Manual Version 5.0
- Table of Contents
- List of Figures
- List of Tables
- Notices
- 1. Overview
- 2. Physical Description
- 3. Installation
- 4. Getting Started
- 5. Web Management
- Computer Requirements
- Protection and Security Mechanisms
- Accessing the Embedded Web Server
- Getting Acquainted with the Web Interface
- Protocol Management
- Advanced Configuration
- Status & Diagnostic
- Software Update Menu
- Maintenance
- Logging Off the Embedded Web Server
- 6. Gateway's ini File Configuration
- Secured ini File
- Modifying an ini File
- The ini File Content
- The ini File Structure
- The ini File Example
- Networking Parameters
- System Parameters
- Web and Telnet Parameters
- Security Parameters
- RADIUS Parameters
- SNMP Parameters
- SIP Configuration Parameters
- Voice Mail Parameters
- ISDN and CAS Interworking-Related Parameters
- Number Manipulation and Routing Parameters
- E1/T1 Configuration Parameters
- Channel Parameters
- Configuration Files Parameters
- 7. Using BootP / DHCP
- 8. Telephony Capabilities
- Working with Supplementary Services
- Configuring the DTMF Transport Types
- Fax & Modem Transport Modes
- Event Notification using X-Detect Header
- ThroughPacket™
- Dynamic Jitter Buffer Operation
- Configuring the Gateway’s Alternative Routing (based on Conn
- Call Detail Report
- Supported RADIUS Attributes
- Trunk to Trunk Routing Example
- Proxy or Registrar Registration Example
- SIP Call Flow Example
- SIP Authentication Example
- 9. Networking Capabilities
- 10. Advanced PSTN Configuration
- 11. Advanced System Capabilities
- 12. Special Applications
- 13. Security
- 14. Diagnostics
- 15. SNMP-Based Management
- SNMP Standards and Objects
- Carrier Grade Alarm System
- Cold Start Trap
- Third-Party Performance Monitoring Measurements
- TrunkPack-VoP Series Supported MIBs
- Traps
- SNMP Interface Details
- SNMP Manager Backward Compatibility
- Dual Module Interface
- SNMP NAT Traversal
- SNMP Administrative State Control
- AudioCodes’ Element Management System
- 16. Configuration Files
- Appendix A. Selected Technical Specifications
- Appendix B. Supplied SIP Software Kit
- Appendix C. SIP Compliance Tables
- Appendix D. The BootP/TFTP Configuration Utility
- Appendix E. RTP/RTCP Payload Types and Port Allocation
- Appendix F. RTP Control Protocol Extended Reports (RTCP-XR)
- Appendix G. Accessory Programs and Tools
- Appendix H. Release Reason Mapping
- Appendix I. SNMP Traps
- Appendix J. Installation and Configuration of Apache HTTP Server
- Appendix K. Regulatory Information
SIP User's Manual D. The BootP/TFTP Configuration Utility
Version 5.0 353 October 2006
D The BootP/TFTP Configuration Utility
The BootP/TFTP utility enables you to easily configure and provision our boards and media
gateways. Similar to third-party BootP/TFTP utilities (which are also supported) but with
added functionality; our BootP/TFTP utility can be installed on Windows™ 98 or
Windows™ NT/2000/XP. The BootP/TFTP utility enables remote reset of the device to
trigger the initialization procedure (BootP and TFTP). It contains BootP and TFTP utilities
with specific adaptations to our requirements.
D.1 When to Use the BootP/TFTP
The BootP/TFTP utility can be used with the device as an alternative means of initializing
the gateways. Initialization provides a gateway with an IP address, subnet mask, and the
default gateway IP address. The tool also loads default software, ini and other
configuration files. BootP Tool can also be used to restore a gateway to its initial
configuration, such as in the following instances:
The IP address of the gateway is not known.
The Web browser has been inadvertently turned off.
The Web browser password has been forgotten.
The gateway has encountered a fault that cannot be recovered using the Web
browser.
Tip: The BootP is normally used to configure the device’s initial parameters.
Once this information has been provided, the BootP is no longer needed.
All parameters are stored in non-volatile memory and used when the BootP
is not accessible.
D.2 An Overview of BootP
BootP is a protocol defined in RFC 951 and RFC 1542 that enables an internet device to
discover its own IP address and the IP address of a BootP on the network, and to obtain
the files from that utility that need to be loaded into the device to function.
A device that uses BootP when it powers up broadcasts a BootRequest message on the
network. A BootP on the network receives this message and generates a BootReply. The
BootReply indicates the IP address that should be used by the device and specifies an IP
address from which the unit may load configuration files using Trivial File Transfer Protocol
(TFTP) described in RFC 906 and RFC 1350.
D.3 Key Features
Internal BootP supporting hundreds of entities.
Internal TFTP.
Contains all required data for our products in predefined format.
Provides a TFTP address, enabling network separation of TFTP and BootP utilities.
Tools to backup and restore the local database.
Templates.
User-defined names for each entity.
Option for changing MAC address.
Protection against entering faulty information.
Remote reset.