User`s manual
Table Of Contents
- Mediant 2000 & TP-1610 & TP-260/UNI SIP User’s Manual Version 5.0
- Table of Contents
- List of Figures
- List of Tables
- Notices
- 1. Overview
- 2. Physical Description
- 3. Installation
- 4. Getting Started
- 5. Web Management
- Computer Requirements
- Protection and Security Mechanisms
- Accessing the Embedded Web Server
- Getting Acquainted with the Web Interface
- Protocol Management
- Advanced Configuration
- Status & Diagnostic
- Software Update Menu
- Maintenance
- Logging Off the Embedded Web Server
- 6. Gateway's ini File Configuration
- Secured ini File
- Modifying an ini File
- The ini File Content
- The ini File Structure
- The ini File Example
- Networking Parameters
- System Parameters
- Web and Telnet Parameters
- Security Parameters
- RADIUS Parameters
- SNMP Parameters
- SIP Configuration Parameters
- Voice Mail Parameters
- ISDN and CAS Interworking-Related Parameters
- Number Manipulation and Routing Parameters
- E1/T1 Configuration Parameters
- Channel Parameters
- Configuration Files Parameters
- 7. Using BootP / DHCP
- 8. Telephony Capabilities
- Working with Supplementary Services
- Configuring the DTMF Transport Types
- Fax & Modem Transport Modes
- Event Notification using X-Detect Header
- ThroughPacket™
- Dynamic Jitter Buffer Operation
- Configuring the Gateway’s Alternative Routing (based on Conn
- Call Detail Report
- Supported RADIUS Attributes
- Trunk to Trunk Routing Example
- Proxy or Registrar Registration Example
- SIP Call Flow Example
- SIP Authentication Example
- 9. Networking Capabilities
- 10. Advanced PSTN Configuration
- 11. Advanced System Capabilities
- 12. Special Applications
- 13. Security
- 14. Diagnostics
- 15. SNMP-Based Management
- SNMP Standards and Objects
- Carrier Grade Alarm System
- Cold Start Trap
- Third-Party Performance Monitoring Measurements
- TrunkPack-VoP Series Supported MIBs
- Traps
- SNMP Interface Details
- SNMP Manager Backward Compatibility
- Dual Module Interface
- SNMP NAT Traversal
- SNMP Administrative State Control
- AudioCodes’ Element Management System
- 16. Configuration Files
- Appendix A. Selected Technical Specifications
- Appendix B. Supplied SIP Software Kit
- Appendix C. SIP Compliance Tables
- Appendix D. The BootP/TFTP Configuration Utility
- Appendix E. RTP/RTCP Payload Types and Port Allocation
- Appendix F. RTP Control Protocol Extended Reports (RTCP-XR)
- Appendix G. Accessory Programs and Tools
- Appendix H. Release Reason Mapping
- Appendix I. SNMP Traps
- Appendix J. Installation and Configuration of Apache HTTP Server
- Appendix K. Regulatory Information
SIP User's Manual A. Selected Technical Specifications
Version 5.0 337 October 2006
A.2 Mediant 2000 Specifications
Table A-2: Mediant 2000 Selected Technical Specifications (continues on pages 337 to 338)
Function Specification
Trunk & Channel Capacity
2
Capacity with E1
1, 2, 4, 8 or 16 E1 spans, 30, 60, 120, 240 or 480 digital channels:
30 Channels on 1 E1 span with gateway-1 only
60 Channels on 2 E1 spans with gateway-1 only
120 Channels on 4 E1 spans with gateway-1 only
240 Channels on 8 E1 spans with gateway-1 only
480 Channels on 16 E1 spans with gateway-1 and gateway-2
Capacity with T1
1, 2, 4, 8 or 16 T1 spans, 24, 48, 96, 192 or 384 digital channels
24 Channels on 1 T1 span with gateway-1 only
48 Channels on 2 T1 spans with gateway-1 only
96 Channels on 4 T1 spans with gateway-1 only
192 Channels on 8 T1 spans with gateway-1 only
384 Channels on 16 T1 spans with gateway-1 and gateway-2
Interfaces
Telephony Interface
1, 2, 4, 8 or 16 E1/T1/J1 Balanced 120/100 ohm, or 75 ohm using a BNC to RJ-
45 dual E1/T1 G.703 Balun adapter
3
.
Network Interface
Two 10/100 Base-TX, half or full duplex with auto-negotiation
RS-232 Interface
RS-232 Terminal Interface. DB-9 connector on rear panel (available only on the
1, 2 and 4-span configuration).
LED Indicators
LED Indications on Front
Panel
Power, ACT/Fail, T1/E1 status, LAN status, Swap ready indication
Connectors & Switches
Rear Panel
Trunks
1 to 8 and 9 to 16
Two 50-pin female Telco connectors (DDK57AE-40500-21D) or 8 RJ-48c
connectors for trunks 1 to 8 only
Ethernet 1 and 2
Two 10/100 Base-TX, RJ-45 shielded connectors
RS-232
Console port - DB-9
AC Power
Standard IEC320 Appliance inlet.
Option for a dual (fully redundant) power supply.
2-pin terminal block (screw connection type) suitable for field wiring applications
connecting DC Power connector: MSTB2.5/2-STF (5.08 mm) from Phoenix
Contact.
Bonding and earthing: A 6-32-UNC screw is provided. Correct ring terminal and
16 AWG wire minimum must be used for connection.
Or crimp connection shown below.
DC Power
Note that to meet UL approvals, users must fulfill the criteria below.
2-pin terminal block (crimp connection type) comprising a Phoenix Contact
Adaptor: Shroud: MSTBC2,5/2-STZF-5,08.
Contacts: MSTBC-MT0,5-1,0
Cable requirement: 18 AWG x 1.5 m length.
2
Mediant 2000 channel capacity depends on configuration settings.
3
The following Balun adaptors were tested and certified by AudioCodes:
Manufacture Name: AC&E Part Number: B04040072
Manufacture Name: RIT Part Number: R3712271