User`s manual
Table Of Contents
- Mediant 2000 & TP-1610 & TP-260/UNI SIP User’s Manual Version 5.0
- Table of Contents
- List of Figures
- List of Tables
- Notices
- 1. Overview
- 2. Physical Description
- 3. Installation
- 4. Getting Started
- 5. Web Management
- Computer Requirements
- Protection and Security Mechanisms
- Accessing the Embedded Web Server
- Getting Acquainted with the Web Interface
- Protocol Management
- Advanced Configuration
- Status & Diagnostic
- Software Update Menu
- Maintenance
- Logging Off the Embedded Web Server
- 6. Gateway's ini File Configuration
- Secured ini File
- Modifying an ini File
- The ini File Content
- The ini File Structure
- The ini File Example
- Networking Parameters
- System Parameters
- Web and Telnet Parameters
- Security Parameters
- RADIUS Parameters
- SNMP Parameters
- SIP Configuration Parameters
- Voice Mail Parameters
- ISDN and CAS Interworking-Related Parameters
- Number Manipulation and Routing Parameters
- E1/T1 Configuration Parameters
- Channel Parameters
- Configuration Files Parameters
- 7. Using BootP / DHCP
- 8. Telephony Capabilities
- Working with Supplementary Services
- Configuring the DTMF Transport Types
- Fax & Modem Transport Modes
- Event Notification using X-Detect Header
- ThroughPacket™
- Dynamic Jitter Buffer Operation
- Configuring the Gateway’s Alternative Routing (based on Conn
- Call Detail Report
- Supported RADIUS Attributes
- Trunk to Trunk Routing Example
- Proxy or Registrar Registration Example
- SIP Call Flow Example
- SIP Authentication Example
- 9. Networking Capabilities
- 10. Advanced PSTN Configuration
- 11. Advanced System Capabilities
- 12. Special Applications
- 13. Security
- 14. Diagnostics
- 15. SNMP-Based Management
- SNMP Standards and Objects
- Carrier Grade Alarm System
- Cold Start Trap
- Third-Party Performance Monitoring Measurements
- TrunkPack-VoP Series Supported MIBs
- Traps
- SNMP Interface Details
- SNMP Manager Backward Compatibility
- Dual Module Interface
- SNMP NAT Traversal
- SNMP Administrative State Control
- AudioCodes’ Element Management System
- 16. Configuration Files
- Appendix A. Selected Technical Specifications
- Appendix B. Supplied SIP Software Kit
- Appendix C. SIP Compliance Tables
- Appendix D. The BootP/TFTP Configuration Utility
- Appendix E. RTP/RTCP Payload Types and Port Allocation
- Appendix F. RTP Control Protocol Extended Reports (RTCP-XR)
- Appendix G. Accessory Programs and Tools
- Appendix H. Release Reason Mapping
- Appendix I. SNMP Traps
- Appendix J. Installation and Configuration of Apache HTTP Server
- Appendix K. Regulatory Information
SIP User's Manual 15. SNMP-Based Management
Version 5.0 313 October 2006
acAlarm: This is AudioCodes' proprietary carrier-grade alarm MIB. It is a simpler
implementation of the notificationLogMIB and the IETF suggested alarmMIB (both also
supported in all AudioCodes’ devices).
The acAlarm MIB has the following groups:
• ActiveAlarm: straightforward (single-indexed) table, listing all currently active
alarms, together with their bindings (the alarm bindings are defined in acAlarm.
acAlarmVarbinds and also in acBoard.acTrap. acBoardTrapDefinitions.
oid_1_3_6_1_4_1_5003_9_10_1_21_2_0).
• acAlarmHistory: straightforward (single-indexed) table, listing all recently raised
alarms together with their bindings (the alarm bindings are defined in acAlarm.
acAlarmVarbinds and also in acBoard.acTrap. acBoardTrapDefinitions.
oid_1_3_6_1_4_1_5003_9_10_1_21_2_0).
The table size can be altered via
notificationLogMIB.notificationLogMIBObjects.nlmConfig.nlmConfigGlobalEntryLimit or
notificationLogMIB.notificationLogMIBObjects.nlmConfig.nlmConfigLogTable.nlm
ConfigLogEntry.nlmConfigLogEntryLimit.
The table size can be any value between 50 and 1000 (default is 500).
Note 1: The following are special notes pertaining to MIBs:
• A detailed explanation of each parameter can be viewed in an
SNMP browser in the "MIB Description" field.
• Not all groups in the MIB are functional. Refer to version release
notes.
• Certain parameters are non-functional. Their MIB status is marked
"obsolete".
• When a parameter is set to a new value via SNMP, the change may
affect device functionality immediately or may require that the
device be soft reset for the change to take effect. This depends on
the parameter type.
Note 2: The current (updated) device configuration parameters are programmed
into the device provided that the user does not load an ini file to the device
after reset. Loading an ini file after reset overrides the updated parameters.