User`s manual

Mediant 2000 & TP-1610 & TP-260
SIP User's Manual 136 Document #: LTRT-68805
Table 6-1: Networking Parameters (continues on pages 130 to 138)
ini File Field Name
Web Parameter Name
Valid Range and Description
PPPoEUserName
User Name for PAP or Host Name for CHAP authentication.
The valid range is a string of up to 47 characters. The default value is 0.
PPPoEPassword
Password for PAP or Secret for CHAP authentication.
The valid range is a string of up to 47 characters. The default value is 0.
PPPoEServerName
Server Name for CHAP authentication.
The valid range is a string of up to 47 characters. The default value is 0.
PPPoEStaticIPAddress
IP address to use in a static configuration setup. If set, used during PPP
negotiation to request this specific IP address from the PPP server. If approved by
the server, this IP address is used during the session.
The valid IP address range is in dotted notation xxx.xxx.xxx.xxx. The default value
is 0.0.0.0.
PPPoERecoverIPAddres
s
IP address to use when booting from the flash to non-PPPoE (Point-to-Point
Protocol over Ethernet) environments.
The valid IP address range is in dotted notation xxx.xxx.xxx.xxx. The default value
is 10.4.10.4.
PPPoERecoverSubnetM
ask
Subnet Mask to use when booting from the flash to non-PPPoE (Point-to-Point
Protocol over Ethernet) environments.
The valid IP address range is in dotted notation xxx.xxx.xxx.xxx. The default value
is 255.255.0.0.
PPPoERecoverDfgwAdd
ress
Default GW address to use when booting from the flash to non-PPPoE (Point-to-
Point Protocol over Ethernet) environments.
The valid IP address range is in dotted notation xxx.xxx.xxx.xxx. The default value
is 10.4.10.1.
PPPoELCPEchoEnable
Enables or disables the Point-to-Point Protocol over Ethernet (PPPoE)
disconnection auto-detection feature.
Valid options include:
0 = Disable
1 = Enable (default)
By default, the PPPoE Client (i.e., embedded in the gateway) sends LCP Echo
packets to the server to check that the PPPoE connection is open. Some Access
Concentrators (PPPoE servers) don't reply to these LCP Echo requests, resulting
in a disconnection. By disabling the LCP disconnection auto-detection feature, the
PPPoE Client doesn't send LCP Echo packets to the server (and does not detect
PPPoE disconnections).
Differential Services.
For detailed information on IP QoS via Differentiated Services, refer to Section 9.9 on page 236.
NetworkServiceClassDiffSe
rv
[Network QoS]
Sets the DiffServ value for Network service class content.
The valid range is 0 to 56. The default value is 48.
PremiumServiceClassMedi
aDiffServ
[Media Premium QoS]
Sets the DiffServ value for Premium Media service class content (only if
IPDiffServ is not set in the selected IP Profile).
The valid range is 0 to 56. The default value is 46.
Note: The value for the Premium Control DiffServ is determined by (according
to priority):
(1) IPDiffServ value in the selected IP Profile.
(2) PremiumServiceClassMediaDiffServ.
PremiumServiceClassCont
rolDiffServ
[Control Premium QoS]
Sets the DiffServ value for Premium Control service class content (only if
ControlIPDiffserv is not set in the selected IP Profile).
The valid range is 0 to 56. The default value is 46.
Note: The value for the Premium Control DiffServ is determined by (according
to priority):
(1) ControlPDiffserv value in the selected IP Profile.
(2) PremiumServiceClassControlDiffServ.
GoldServiceClassDiffServ
[Gold QoS]
Sets the DiffServ value for the Gold service class content.
The valid range is 0 to 56. The default value is 26.