User`s manual
Table Of Contents
- Mediant 2000 & TP-1610 & TP-260/UNI SIP User’s Manual Version 5.0
- Table of Contents
- List of Figures
- List of Tables
- Notices
- 1. Overview
- 2. Physical Description
- 3. Installation
- 4. Getting Started
- 5. Web Management
- Computer Requirements
- Protection and Security Mechanisms
- Accessing the Embedded Web Server
- Getting Acquainted with the Web Interface
- Protocol Management
- Advanced Configuration
- Status & Diagnostic
- Software Update Menu
- Maintenance
- Logging Off the Embedded Web Server
- 6. Gateway's ini File Configuration
- Secured ini File
- Modifying an ini File
- The ini File Content
- The ini File Structure
- The ini File Example
- Networking Parameters
- System Parameters
- Web and Telnet Parameters
- Security Parameters
- RADIUS Parameters
- SNMP Parameters
- SIP Configuration Parameters
- Voice Mail Parameters
- ISDN and CAS Interworking-Related Parameters
- Number Manipulation and Routing Parameters
- E1/T1 Configuration Parameters
- Channel Parameters
- Configuration Files Parameters
- 7. Using BootP / DHCP
- 8. Telephony Capabilities
- Working with Supplementary Services
- Configuring the DTMF Transport Types
- Fax & Modem Transport Modes
- Event Notification using X-Detect Header
- ThroughPacket™
- Dynamic Jitter Buffer Operation
- Configuring the Gateway’s Alternative Routing (based on Conn
- Call Detail Report
- Supported RADIUS Attributes
- Trunk to Trunk Routing Example
- Proxy or Registrar Registration Example
- SIP Call Flow Example
- SIP Authentication Example
- 9. Networking Capabilities
- 10. Advanced PSTN Configuration
- 11. Advanced System Capabilities
- 12. Special Applications
- 13. Security
- 14. Diagnostics
- 15. SNMP-Based Management
- SNMP Standards and Objects
- Carrier Grade Alarm System
- Cold Start Trap
- Third-Party Performance Monitoring Measurements
- TrunkPack-VoP Series Supported MIBs
- Traps
- SNMP Interface Details
- SNMP Manager Backward Compatibility
- Dual Module Interface
- SNMP NAT Traversal
- SNMP Administrative State Control
- AudioCodes’ Element Management System
- 16. Configuration Files
- Appendix A. Selected Technical Specifications
- Appendix B. Supplied SIP Software Kit
- Appendix C. SIP Compliance Tables
- Appendix D. The BootP/TFTP Configuration Utility
- Appendix E. RTP/RTCP Payload Types and Port Allocation
- Appendix F. RTP Control Protocol Extended Reports (RTCP-XR)
- Appendix G. Accessory Programs and Tools
- Appendix H. Release Reason Mapping
- Appendix I. SNMP Traps
- Appendix J. Installation and Configuration of Apache HTTP Server
- Appendix K. Regulatory Information
Mediant 2000 & TP-1610 & TP-260
SIP User's Manual 130 Document #: LTRT-68805
6.6 Networking Parameters
Table 6-1: Networking Parameters (continues on pages 130 to 138)
ini File Field Name
Web Parameter Name
Valid Range and Description
EthernetPhyConfiguration
0 = 10 Base-T half-duplex
1 = 10 Base-T full-duplex
2 = 100 Base-TX half-duplex
3 = 100 Base-TX full-duplex
4 = auto-negotiate (default)
For detailed information on Ethernet interface configuration, refer to Section
9.1
on page 229.
DHCPEnable
[Enable DHCP]
0 = Disable DHCP support on the gateway (default).
1 = Enable DHCP support on the gateway.
After the gateway is powered up, it attempts to communicate with a BootP
server. If a BootP server is not responding and if DHCP is enabled, then the
gateway attempts to get its IP address and other network parameters from the
DHCP server.
Web Note: After you enable the DHCP Server (from the Web browser) follow
this procedure:
• Click the Submit button.
• Save the configuration using the Maintenance button (before you reset the
gateway). For information on how to save the configuration, refer to
Section 5.9.2 on page 124.
• Reset the gateway directly (Web reset doesn’t trigger the BootP/DHCP
procedure and the parameter DHCPEnable reverts to ‘0’).
Note that throughout the DHCP procedure the BootP/TFTP application must be
deactivated. Otherwise, the gateway receives a response from the BootP server
instead of the DHCP server.
Note: The DHCPEnable is a special ‘Hidden’ parameter. Once defined and
saved in flash memory, its assigned value doesn’t revert to its default even if
the parameter doesn't appear in the ini file.
EnableLanWatchDog
[Enable LAN Watchdog]
0 = Disable LAN Watch-Dog (default).
1 = Enable LAN Watch-Dog.
When LAN Watch-Dog is enabled, the gateway's overall communication
integrity is checked periodically. If no communication for about 3 minutes is
detected, the gateway performs a self test.
• If the self test succeeds, the problem is logical link down (i.e. Ethernet
cable disconnected on the switch side), and the Busy out mechanism is
activated if enabled (EnableBusyOut = 1).
• If the self test fails, the gateway restarts to overcome internal fatal
communication error.
Note: Enable LAN Watchdog is relevant only if the Ethernet connection is full
duplex.
DNSPriServerIP
[DNS Primary Server IP]
IP address of the primary DNS server in dotted format notation.
DNSSecServerIP
[DNS Secondary Server IP]
IP address of the secondary DNS server in dotted format notation.