User`s manual
Table Of Contents
- Mediant 2000 & TP-1610 & TP-260/UNI SIP User’s Manual Version 5.0
- Table of Contents
- List of Figures
- List of Tables
- Notices
- 1. Overview
- 2. Physical Description
- 3. Installation
- 4. Getting Started
- 5. Web Management
- Computer Requirements
- Protection and Security Mechanisms
- Accessing the Embedded Web Server
- Getting Acquainted with the Web Interface
- Protocol Management
- Advanced Configuration
- Status & Diagnostic
- Software Update Menu
- Maintenance
- Logging Off the Embedded Web Server
- 6. Gateway's ini File Configuration
- Secured ini File
- Modifying an ini File
- The ini File Content
- The ini File Structure
- The ini File Example
- Networking Parameters
- System Parameters
- Web and Telnet Parameters
- Security Parameters
- RADIUS Parameters
- SNMP Parameters
- SIP Configuration Parameters
- Voice Mail Parameters
- ISDN and CAS Interworking-Related Parameters
- Number Manipulation and Routing Parameters
- E1/T1 Configuration Parameters
- Channel Parameters
- Configuration Files Parameters
- 7. Using BootP / DHCP
- 8. Telephony Capabilities
- Working with Supplementary Services
- Configuring the DTMF Transport Types
- Fax & Modem Transport Modes
- Event Notification using X-Detect Header
- ThroughPacket™
- Dynamic Jitter Buffer Operation
- Configuring the Gateway’s Alternative Routing (based on Conn
- Call Detail Report
- Supported RADIUS Attributes
- Trunk to Trunk Routing Example
- Proxy or Registrar Registration Example
- SIP Call Flow Example
- SIP Authentication Example
- 9. Networking Capabilities
- 10. Advanced PSTN Configuration
- 11. Advanced System Capabilities
- 12. Special Applications
- 13. Security
- 14. Diagnostics
- 15. SNMP-Based Management
- SNMP Standards and Objects
- Carrier Grade Alarm System
- Cold Start Trap
- Third-Party Performance Monitoring Measurements
- TrunkPack-VoP Series Supported MIBs
- Traps
- SNMP Interface Details
- SNMP Manager Backward Compatibility
- Dual Module Interface
- SNMP NAT Traversal
- SNMP Administrative State Control
- AudioCodes’ Element Management System
- 16. Configuration Files
- Appendix A. Selected Technical Specifications
- Appendix B. Supplied SIP Software Kit
- Appendix C. SIP Compliance Tables
- Appendix D. The BootP/TFTP Configuration Utility
- Appendix E. RTP/RTCP Payload Types and Port Allocation
- Appendix F. RTP Control Protocol Extended Reports (RTCP-XR)
- Appendix G. Accessory Programs and Tools
- Appendix H. Release Reason Mapping
- Appendix I. SNMP Traps
- Appendix J. Installation and Configuration of Apache HTTP Server
- Appendix K. Regulatory Information
SIP User's Manual 5. Web Management
Version 5.0 107 October 2006
Table 5-12: IP Connectivity Parameters
Column Name Description
IP Address
IP address defined in the destination IP address field in the Tel to IP Routing table.
or
IP address that is resolved from the host name defined in the destination IP address field
in the Tel to IP Routing table.
Host Name
Host name (or IP address) defined in the destination IP address field in the Tel to IP
Routing table.
Connectivity Method
The method according to which the destination IP address is queried periodically
(currently only by ping).
Connectivity Status
Displays the status of the IP address’ connectivity according to the method in the
‘Connectivity Method’ field.
Can be one of the following:
• OK = Remote side responds to periodic connectivity queries.
• Lost = Remote side didn’t respond for a short period.
• Fail = Remote side doesn’t respond.
• Init = Connectivity queries not started (e.g., IP address not resolved).
• Disable = The connectivity option is disabled (‘AltRoutingTel2IPMode’ equals 0
or 2).
Quality Status
Determines the QoS (according to packet loss and delay) of the IP address.
Can be one of the following:
• Unknown = Recent quality information isn’t available.
• OK
• Poor
Note 1: This field is applicable only if the parameter ‘AltRoutingTel2IPMode’ is set to 2 or
3.
Note 2: This field is reset if no QoS information is received for 2 minutes.
Quality Info.
Displays QoS information: delay and packet loss, calculated according to previous calls.
Note 1: This field is applicable only if the parameter ‘AltRoutingTel2IPMode’ is set to 2 or
3.
Note 2: This field is reset if no QoS information is received for 2 minutes.
DNS Status
Can be one of the following:
• DNS Disable
• DNS Resolved
• DNS Unresolved