User`s manual
Table Of Contents
- Mediant 2000 & TP-1610 & TP-260/UNI SIP User’s Manual Version 5.0
- Table of Contents
- List of Figures
- List of Tables
- Notices
- 1. Overview
- 2. Physical Description
- 3. Installation
- 4. Getting Started
- 5. Web Management
- Computer Requirements
- Protection and Security Mechanisms
- Accessing the Embedded Web Server
- Getting Acquainted with the Web Interface
- Protocol Management
- Advanced Configuration
- Status & Diagnostic
- Software Update Menu
- Maintenance
- Logging Off the Embedded Web Server
- 6. Gateway's ini File Configuration
- Secured ini File
- Modifying an ini File
- The ini File Content
- The ini File Structure
- The ini File Example
- Networking Parameters
- System Parameters
- Web and Telnet Parameters
- Security Parameters
- RADIUS Parameters
- SNMP Parameters
- SIP Configuration Parameters
- Voice Mail Parameters
- ISDN and CAS Interworking-Related Parameters
- Number Manipulation and Routing Parameters
- E1/T1 Configuration Parameters
- Channel Parameters
- Configuration Files Parameters
- 7. Using BootP / DHCP
- 8. Telephony Capabilities
- Working with Supplementary Services
- Configuring the DTMF Transport Types
- Fax & Modem Transport Modes
- Event Notification using X-Detect Header
- ThroughPacket™
- Dynamic Jitter Buffer Operation
- Configuring the Gateway’s Alternative Routing (based on Conn
- Call Detail Report
- Supported RADIUS Attributes
- Trunk to Trunk Routing Example
- Proxy or Registrar Registration Example
- SIP Call Flow Example
- SIP Authentication Example
- 9. Networking Capabilities
- 10. Advanced PSTN Configuration
- 11. Advanced System Capabilities
- 12. Special Applications
- 13. Security
- 14. Diagnostics
- 15. SNMP-Based Management
- SNMP Standards and Objects
- Carrier Grade Alarm System
- Cold Start Trap
- Third-Party Performance Monitoring Measurements
- TrunkPack-VoP Series Supported MIBs
- Traps
- SNMP Interface Details
- SNMP Manager Backward Compatibility
- Dual Module Interface
- SNMP NAT Traversal
- SNMP Administrative State Control
- AudioCodes’ Element Management System
- 16. Configuration Files
- Appendix A. Selected Technical Specifications
- Appendix B. Supplied SIP Software Kit
- Appendix C. SIP Compliance Tables
- Appendix D. The BootP/TFTP Configuration Utility
- Appendix E. RTP/RTCP Payload Types and Port Allocation
- Appendix F. RTP Control Protocol Extended Reports (RTCP-XR)
- Appendix G. Accessory Programs and Tools
- Appendix H. Release Reason Mapping
- Appendix I. SNMP Traps
- Appendix J. Installation and Configuration of Apache HTTP Server
- Appendix K. Regulatory Information
Mediant 2000 & TP-1610 & TP-260
SIP User's Manual 102 Document #: LTRT-68805
¾ To delete a rule, take these 3 steps:
1. Click the radio button of the entry you want to activate.
2. Click the Delete Rule button; the rule is deleted.
3. To save the changes so they are available after a power fail, refer to Section 5.9.2 on
page 124.
5.6.8.4 Configuring the Certificates
Use the Certificates screen to replace the server (refer to Section 13.2.4 on page 291) and
client (refer to Section
13.2.5 on page 293) certificates and to update the private key
(HTTPSPkeyFileName, described in Table
6-3 on page 143).
5.6.8.5 Configuring the IPSec Table
Use the IPSec Table screen to configure the IPSec parameters. For detailed information on
IPSec and IKE, refer to Section
13.1 on page 281.
5.6.8.6 Configuring the IKE Table
Use the IKE Table screen to configure the IKE parameters. For detailed information on
IPSec and IKE, refer to Section
13.1 on page 281.
5.6.9 Configuring the Management Settings
From the Management Settings you can:
Configure the Syslog Settings.
Configure the SNMP Managers Table (refer to Section 5.6.9.1 below).
Configure the SNMP Community Strings (refer to Section 5.6.9.2 on page 104).
SNMP v3 Users (refer to Section 5.6.9.3 on page 105).