QUALITY, RELIABILITY, & PURE BLISS MATCHED COMPONENT SPEAKER SYSTEM ABC6003N / ABC6002N / ABC5002N / ABC4002N OPERATING INTSTRUCTIONS PLEASE RETAIN MANUAL FOR FUTURE USE AND REFERENCE
The Audiobahn Way � To bring the product to market that excites the consumer through sound and vision from an orientation of integrity and customer service. We make you look as good as you sound. We strive to take car audio to an extreme the world has never seen, and a world that never stops evolving.
Table of Contents Getting Started----------------------------------------------------- 2 Introduction---------------------------------------------------------- 3 Features and Specifications------------------------------------- 4 Mounting and Setup------------------------------------------------ 5-8 Choosing a Location----------------------------------------------- 9 Installation------------------------------------------------------------ 10 Wiring------------------------------------------------------------
Introduction Dear Customer, Congratulations on your purchase of the worlds finest brand of car audio products. Here at Audiobahn Inc. we are devoted to making our musical reproduction the vert best, and we are pleased you have chosen our product. Through years of engineering expertise, hand craftsmanship, and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve.
Features and Specifications FEATURES CARBON HONEYCOMB CONE BUTYL RUBBER SURROUND CHROME PLATED CAST ALUMINUM BASKET 2-LAYER HIGH-TRMP ASV VOICE COIL 4 OHM IMPEDANCE COMPONENT MATHED 18dB PER OCTAVE CROSSOVER NETWORK 25mm SILK DOME TWEETER (SURFACE OR FLUSH MOUNT) COMPLETE WITH MOUNTING HARDWARE STRONTIUM MID-WOOFER MAGNET NEODYNIUM TWEETER MAGNET SPECIFICATIONS POWER HANDLING ABC6003N: 320 RMS POWER 640 ACH POWER ABC6002N: 200 RMS POWER 400 ACH POWER ABC5002N: 160 RMS POWER 320 ACH POWER ABC4002N: 120 RMS
Mounting ABC4002N / ABC5002N / ABC6002N Amplifier Amplifier Tweeter Midwoofer ABC6003N Amplifier Midwoofer Woofer Tweeter Amplifier 5
Mounting ABC6003N ABC4002N / ABC5002N / ABC6002N The red arrows above point the separate terminals on the crossover. The left terminal in each set is (-) negative, and the right terminal is (+) positive. ABC6003N ABC4002N / ABC5002N / ABC6002N 2 1 2 1 The red arrows in the diagram above (1, 2) point to the tweeter attenuation. Setting the switch to position (1) sets the attenuation to 0dB. Setting the switch to position (2) sets the attenuation to -3dB.
7
8
Choosing A Location It is always best to plan the complete installation prior to attempting to install any product. The routing of wires, power connections and mounting locations should be planned first. As with any car stereo installation, and all work performed should be checked thoroughly and carefully prior to the operation of the system. The placement of your Audiobahn speakers within your vehicle will greatly affect the overall performance of your audio system.
Installation Installation Note: Audiobahn strongly recommends that you operate your system at low volumes prior to the completed installation of your Audiobahn speakers. This will allow a test of the speaker before securing it to its permanent location. Caution: Make sure that all speaker wiring is fully protected from cuts, tears and possible wear. All short circuits developing as a result could severely damage the source unit or possibly the amplifier as well as the speakers themselves.
Wiring Wiring Audiobahn recommends using at least 18-gauge wire with your new speaker system. Thinner gauge wire may easily be severed and can cause damage to your system should any bare wires come in contact with the vehicles chassis. Makes sure that your audio system is off while installing and connecting your new Audiobahn Speakers. Failure to do so could result in damaging the speaker beyond repair. This is not something that would be covered under the manufacturer warranty.
Securing the Speaker Securing the Speaker Once you have tested your system and confirmed that it is operating properly, turn off your system and prepare for the final mounting of the speakers. 1) Position the speaker into the mounting hole and confirm the correct mounting location and hole placement. Screw clips are provided to insure a snug fit. Place crew clips over the metal surface and line up the hole with the hole you have previously drilled. Place the speaker into the hole.
Troubleshooting In the event that your Audiobahn speakers appear to require service we ask that you first do a little trouble shooting to determine if the problem is actually the speaker, or a problem located in a different part of the vehicle such as the amplifier, wiring, fusing or possibly the source unit.
Technical Assistance(800)488-8595 /tech@audiobahninc.com Warning / Disclaimer WARNING Investigate the layout of your automobile thoroughly before drilling or cutting any holes. Take care when you work near the gas tanks,gas lines, hydraulic lines, and electrical wiring. Do not use the power amplifier unmounted. Attach the system securely to the automobile to prevent damage, particularly in the event of an accident.
Technical Assistance (800)488-8595 /tech@audiobahninc.com Warranty Continued How to receive warranty service: Contact your local Authorized Audiobahn Dealer, or call Audiobahn at (800) 488-8595 between the hours of 9:00 AM and 5:00 PM PST. If you are having problems with your system, we recommend you check the product carefully and thoroughly to confirm that the product truly has a manufacturer defect; as opposed to abuse, or other components in the system causing the failure.
