QUALITY, RELIABILITY, & PURE BLISS 10-DISC COMPACT DISC PLAYER A1341N OPERATING INTSTRUCTIONS PLEASE RETAIN MANUAL FOR FUTRE USE AND REFERENCE
The Audiobahn Way To bring the product to market that excites the consumer through sound and vision from an orientation of integrity and customer service. We make you look as good as you sound. We strive to take car audio to an extreme the world has never seen, and a world that never stops evolving.
Table of Contents Table of Contents INTRODUCTION 3 HOW TO USE THE MAGAZINE 4 HANDLING DISCS 5 INSTALLATION PARTS 6 BEFORE INSTALLING THE UNIT 7-8 INSTALLATION 9-12 TROUBLESHOOTING 13 WARNING / DISCLAIMER 14 WARRANTY 15-16 HINTS FOR CORRECT AND SAFE OPERATION This CD Changer is designed to be operated only on +12 volt DC negative ground systems. The unit cannot be used on +24 volt or positive ground systems. The unit may not operate correctly in extremely hot or cold temperatures.
Introduction Dear Customer, Congratulations on your purchase of the worlds finest brand of car audio products. Here at Audiobahn Inc. we are devoted to making our musical reproduction the very best, and we are pleased you have chosen our product. Through years of engineering expertise, hand craftsmanship, and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve.
How to use the Magazine ,OADING A DISC 0ICK THE TAB ON THE MAGAZINE S DISC TRAY AND PULL OUT ONLY OF THE TRAYS 0LACE THE DISC ON THE TRAY WITH ITS PLAY SURFACE FACING DOWN LABEL SURFACE FACING UP s %ACH TRAY CAN ACCOMMODATE ONLY ONE DISC ,ABEL SIDE UP 0RESS THE TAB ON THE DISC TRAY TO STORE THE TRAY BACK IN THE MAGAZINE s 5P TO TEN DISCS CAN BE LOADED 0LAY SIDE DOWN )NSTALLING THE MAGAZINE 3LIDE THE DOOR TOWARD THE RIGHT &IRST CHECK THAT THE MAGAZINE WITH THE DISCS HAS ITS TOP S
Handling Discs 7ITH NEW DISCS 4HE SYMPTOMS DESCRIBED BELOW SOMETIMES OCCUR WHEN NEW DISCS ARE USED s 4HE DISC IS NOT PLAYED EVEN WHEN IT IS LOADED s /PERATION CHANGES TO THE NEXT DISC BEFORE THE FIRST DISC HAS A CHANCE TO BE PLAYED s 4HE SAME DISC IS PLAYED OVER AND OVER AGAIN s 4HE DESIGNATED DISC IS NOT PLAYED "URRS "URRS #ENTER HOLE /UTSIDE CIRCMFERENCE 2EMOVE ALL PLASTIC PARTICLES OF BURR FROM SURFACES OF DISC BEFORE LOADING IN MAGAZINE 4HESE SYMPTOMS OCCUR WHEN THERE ARE BURRS ON THE CENTER H
Installation Parts "RACKET ! X "RACKET " X (EXAGONAL "OLT - X 4RUSS 3CREW - X X X 4APPING 3CREW - X $). 0IN #ABLE 3EAL $OUBLE 3IDED 4APE X X X X 7)2).' #ONNECT THIS CABLE TO THE TERMINAL OF THE #$ PLAYER 2%3%4 &5.#4)/.
Beforing Installing the Unit 4RANSPORT ,OCK 3CREWS 4HE MECHANISM IN THE #$ CHANGER IS hLOCKED v INTO PLACE DURING SHIPMENT BY THE TRANSPORT SCREWS "E SURE TO REMOVE THE SCREWS PRIOR TO INSTALLATION #AUTION !FTER REMOVING THE TRANSPORT LOCK SCREWS PLACE THE SUPPLIED SEALS OVER THE SCREW HOLES 4HESE SEALS ARE USED TO KEEP DUST WHICH COULD CAUSE A MALFUNCTION OUT OF THE UNIT )NSTALLATION AND 7IRING 0RECAUTIONS 4O PREVENT A SHORT CIRCUIT s "E SURE TO TURN OFF THE IGNITION AND REMOVE THE NEGATIVE n B
Before Installing the Unit 0OSITION OF THE BUILT IN ANTI VIBRATION BOARD 4HIS UNIT CAN BE INSTALLED HORIZONTALLY SUSPENDED VERTICALLY AND AT A o ANGLE /NCE THE INSTALLATION POSITION HAS BEEN DECIDED IT S NECESSARY TO SET THE POSITION OF THE BUILT IN ANTI VIBRATION BOARD INSIDE THE UNIT 0LEASE DO THIS BEFORE PERFORMING THE PROCEDURE LISTED BELOW 6IBRATION MAY CAUSE THE DISC TO SKIP IF THE UNIT IS USED BEFORE PROPERLY SETTING THE ANTI VIBRATION BOARD s !T THE TIME OF SHIPPING THE BUILT IN ANTI VIBRA
Installation 0ROCEDURE FOR )NSTALLATION ON #ARPET (ORIZONTAL 0OSITION 1 s #ONFIRM THAT THE BUILT IN ANTI VIBRATION BOARDS ON BOTH THE LEFT AND RIGHT SIDES ARE SET TO THE HORIZONTAL INSTALLATION POSITION h v "UILT IN ANTI VIBRATION BOARD POSITION (EXAGON BOLTS - X s !TTACH THE LEFT AND RIGHT BRACKETS ! USING THE HEXAGONAL BOLT - X s !TTACH THE LEFT AND RIGHT BRACKETS ! TO THEIR RESPECTIVE BRACKETS " USING THE HEXAGONAL BOLTS - X AND THE HEXAGONAL NUTS - (EXAGONAL BOLTS - X
Installation 0ROCEDURE FOR )NSTALLATION ON #ARPET 6ERTICAL 0OSITION 1 s 3ET THAT THE BUILT IN ANTI VIBRATION BOARDS ON BOTH THE LEFT AND RIGHT SIDES ARE SET TO THE VERTICAL INSTALLATION POSITION h v "UILT IN ANTI VIBRATION BOARD POSITION (EXAGON BOLTS - X s !TTACH THE LEFT AND RIGHT BRACKETS ! USING THE HEXAGONAL BOLT - X s !TTACH THE LEFT AND RIGHT BRACKETS ! TO THEIR RESPECTIVE BRACKETS " USING THE HEXAGONAL BOLTS - X AND THE HEXAGONAL NUTS - (EXAGONAL BOLTS - X 2 s 0
Installation 0ROCEDURE FOR )NSTALLATION ON #ARPET AT A o ANGLE 1 s 3ET THE BUILT IN ANTI VIBRATION BOARDS ON BOTH THE LEFT AND RIGHT SIDES TO THE o INSTALLATION POSITION h ov "UILT IN ANTI VIBRATION BOARD POSITION s !TTACH THE LEFT AND RIGHT BRACKETS ! USING THE HEXAGONAL BOLT - X (EXAGON BOLTS - X s !TTACH THE LEFT AND RIGHT BRACKETS ! TO THEIR RESPECTIVE BRACKETS " USING THE HEXAGONAL BOLTS - X AND THE HEXAGONAL NUTS - (EXAGONAL BOLTS - X 2 s 0ULL BACK THE CARP
Installation 0ROCEDURE FOR )NSTALLATION 3USPENDED 0OSITION 1 s #ONFIRM THAT THE BUILT IN ANTI VIBRATION BOARDS ON BOTH THE LEFT AND RIGHT SIDES ARE SET TO THE HORIZONTAL INSTALLATION POSITION h v "UILT IN ANTI VIBRATION BOARD POSITION s !TTACH THE LEFT AND RIGHT BRACKETS ! USING THE HEXAGONAL BOLT - X (EXAGONAL "OLTS (EXAGONAL "OLTS 2 3 s $ETERMINE THE MOUNTING LOCATION AND DRILL FOUR MOUNTING HOLES 12 s !TTACH THE #$ CHANGER WITH THE TAPPING SCREWS - X
Troubleshooting $IRT DUST SCRATCHES AND WARPAGE CAUSE SOUND SKIPS DURING PLAYBACK AND A DETERIORATION OF SOUND QUALITY (OW TO TAKE CARE OF YOUR DISC 5SE COMPACT DISCS THAT HAVE THE MARK SHOWN ON THE RIGHT &INGERPRINTS AND DUST SHOULD BE CAREFULLY WIPED OFF THE DISCS SIGNAL SURFACE GLOSSY SIDE WITH A SOFT CLOTH 5NLIKE CONVENTIONAL RECORDS THE COMPACT DISC HAS NO GROOVES TO COLLECT DUST AND MICROSCOPIC DEBRIS SO GENTLY WIPE WITH A SOFT CLOTH SHOULD REMOVE MOST PARTICLES 7IPE IN A STRAIGHT MOTION
4ECHNICAL !SSISTANCE TECH AUDIOBAHNINC COM Warning / Disclaimer WARNING Investigate the layout of your automobile thoroughly before drilling or cutting any holes. Take care when you work near the gas tanks, gas lines, hydraulic lines, and electrical wiring. Attach the system securely to the automobile to prevent damage, particularly in the event of an accident. Do not mount the system so that the wire connections are unprotected or are subject to pinching or damage from nearby objects.
4ECHNICAL !SSISTANCE TECH AUDIOBAHNINC COM Warranty Audiobahn Consumer Product Warranty Policy Audiobahn products are manufactured with the highest quality components and some of the most advanced technology available. Because of this, we recommend that you have your new products installed by an Authorized Audiobahn Dealer.(A list of Authorized Audiobahn Dealers can be found on our web page). Warranty Period: One year from the original date of purchase.
4ECHNICAL !SSISTANCE TECH AUDIOBAHNINC COM Warranty Continued How to receive warranty service: Contact your local Authorized Audiobahn Dealer, or call Audiobahn at (800) 488-8595 between the hours of 9:00 AM and 5:00 PM PST. If you are having problems with your system, we recommend you check the product carefully and thoroughly to confirm that the product truly has a manufacturer defect; as opposed to abuse, or other components in the system causing the failure.
