User Manual UHF SYNTHESIZED WIRELESS TRANSMITTER ATW-T6001 S Thank you for purchasing this product. Before using the product, take time to read this user manual thoroughly to ensure that you will use the product correctly. Also keep this user manual handy, along with the warranty, so that they are always available for reference.
Contents Features ・・・・・・・・・・・・・・・・・・・・・・2 Important information ・・・・・・・・・・・・・・3 Notes on use ・・・・・・・・・・・・・・・・・・・4 Using multiple wireless systems・・・・・・・・・4 Part names and functions ・・・・・・・・・・・・5 Inserting batteries ・・・・・・・・・・・・・・・・・6 Display ・・・・・・・・・・・・・・・・・・・・・・・7 Settings ・・・・・・・・・・・・・・・・・・・・・・8 Menu screen ・・・・・・・・・・・・・・・・・・・・・・・・・・8 Transmission frequency setting ・・・・・・・・・・・・・・・・9 NAME setting ・・・・・・・・・・・・・・・・・・・・・・・・・9 Correcting characters ・・・・・・・・・・・・・・・・・・・・・10 RF power setting ・・・・・・・・・・・・・・・・・・・・
Important information Warning: To prevent fire or shock hazard, do not expose this apparatus to rain or moisture. Caution: Do not expose this apparatus to drips or splashes. To avoid electric shock, do not open the cabinet. Refer servicing to qualified personnel only. Do not expose this apparatus to excessive heat such as sunshine, fire or the like. Do not subject this apparatus to strong impact.
Notes on use · Be sure to read the user manual for any microphone or cable that you attach to the product. · If you use the product close to an electronic or communications device (such as a mobile phone), the product may produce unwanted noise. If this occurs, move the product away from the device. · When setting up and using the product, make sure there are no obstacles between it and the receiver that might block the signal.
Part names and functions Transmission antenna Input connector Connect a microphone (Sold separately). Display Shows the current status. * If no buttons are pressed for a period of 20 seconds, the display will turn off. Power switch Turns the power on/off. SYNC button Use for IR sync with a receiver. Front BACK button Returns to the previous operation. Lever push switch BACK SYNC ON OFF Used for selecting various settings. LR 6 / AA / 単三 ▲ UP ( ) Turn to the right to change a selection.
Inserting batteries 6 1. Slide the battery cover latches inward as shown by the arrows. 2. With the latches pressed in, slide the cover down as shown by the arrow. 3. Open the battery cover as shown in the diagram. 4. Insert the batteries according to the plus (+) and minus (-) marks found inside the battery compartment.
Display The main screen is displayed when the power is switched on. 946. 125MHz (1) (2) (4) (3) (1) Frequency/NAME Press the UP/DOWN to switch screens. * Frequency displays as the default setting. (2) Battery power indicator Shows how much battery power is remaining. : 75 % or more battery power remaining. : 50 to 75 % battery power remaining. : 25 to 50 % battery power remaining. : 25 % or less battery power remaining. : Charge/replace the batteries.
Settings ■ Menu screen Press SET ( ● ) on the lever push switch for menu screen mode. Moving UP ( ▶ ) / DOWN ( ◀ ) takes you to the various setting screens in the order shown below. * If there is no switch operation within 10 seconds, the display returns to the main screen. DOWN (◀) FREQUENCY 946.
■ Transmission frequency setting FREQUENCY 947. 000MHz From the menu screen, use UP/DOWN to select "FREQUENCY," and then press SET. FREQUENCY 947. 000MHz A line is displayed under the first three digits. FREQUENCY 948. 000MHz Use UP/DOWN to select the frequency. FREQUENCY 948. 000MHz Press SET. FREQUENCY 948. 125MHz Use UP/DOWN to select the frequency. A line is displayed under the last three digits. Press SET. "STORED" is displayed, and the transmission frequency setting is complete.
■ Correcting characters To correct a character after it is entered, select "BS" with UP/DOWN. When SET is pressed, the last entered character is deleted and the cursor moves one position to the left. NAME v o c aBS ■ RF power setting RF POWER High From the menu screen, use UP/DOWN to select "RF POWER," and then press SET. RF POWER High Use UP/DOWN to select the RF power. RF POWER Low Press SET. Use UP/DOWN to switch between "High," "Mid" and "Low.
■ Key lock setting LOCK KEY Unlock LOCK KEY Unlock LOCK KEY Lock Display the key lock status. Unlock: Keys unlocked Lock: Keys locked From the menu screen, use UP/DOWN to select "LOCK KEY," and then press SET. Use UP/DOWN to select the key lock setting, then press SET. "STORED" is displayed, and the key lock setting is complete. ■ Lock code setting The lock code is a 4-digit code (from 0000 to 9999) for unlocking the keys.
Using the mute function The mute function allows you to manually mute your microphone when, for example, there is a gap in the middle of a speech, or you want to change the settings and transmitting audio would be a problem. MUTE OFF Unmuted Press and hold When you press and hold the Recall/Mute button, "MUTE ON" is displayed on the screen and your microphone is muted. When you press and hold the Recall/Mute button again, "MUTE OFF" is displayed on the screen and your microphone is unmuted.
IR sync The product is equipped with an IR sync function. It allows you to easily configure the product settings from the receiver. See the receiver's user manual for instructions on how to use IR sync. Attaching the product to user's body The product is equipped with a clip. Use that to attach the product to a belt, pocket or other piece of clothing that will hold it. You can reverse the direction that the input connector faces by attaching the clip in the opposite direction.
Specifications Operating frequency: 946.125 MHz to 949.875 MHz (31 channels) Frequency step: 125 kHz Spurious emissions: Following federal and national regulations RF power output: 50 mW/ 10 mW/ 2 mW Normal deviation: ±5 kHz Maximum deviation: ±16.25 kHz Frequency response: 70 to 15,000 Hz Batteries: Two 1.5 V AA alkaline Operating temperature range: 5 ℃ to 45 ℃ (41 °F to 113 °F) Battery life: Approx.
Memo 15
Audio-Technica Corporation ©2016 Audio-Technica Corp. 232305380-01-01 ver.1 2016.11.
