User Manual
Table Of Contents
- Introduction
- Package contents
- Safety precautions
- Notes on use
- Part names and functions
- Preparation for use
- Placing the platter
- Setting up the turntable
- Assembling the tonearm
- Tonearm balance and tracking force
- Setting tonearm balance
- Setting tracking force
- Setting the anti-skate adjustment
- Installing/removing the dust cover
- Setting output selector switch
- Connecting to connectable equipment (active speakers, amplifiers, etc.)
- Connecting the AC adapter
- Playing a record
- Care
- Replacing the stylus
- Replacing a cartridge
- Replacing the belt
- Adjusting the overhang
- When the turntable is moved
- Troubleshooting
- Dimensions
- Specifications
Specifications
Turntable specifications
Type
Belt-drive manual turntable
Motor DC servo with Active Speed
Stabilization
Drive method Belt drive
Speeds 33-1/3 RPM, 45 RPM
Turntable platter Aluminum Die Casting
Wow and flutter < 0.15 % WRMS (33 RPM) at 3 kHz
Signal-to-noise ratio > 60 dB
Output levels
“PHONO”
“LINE”
4.0 mV nominal at 1 kHz, 5 cm/sec
200 mV nominal at 1 kHz, 5 cm/sec
Phono Pre-amp gain
35 dB nominal, RIAA equalized
Tonearm specifications
Type
Static balanced straight carbon
tonearm
Effective length 223.6 mm
Overhang 18.6 mm
Maximum tracking error angle Less than 2.0°
Stylus pressure adjustment
range
0 to 3.0 g
Applicable cartridge weight
range (including headshell)
11.5 to 16.5 g
Cartridge and headshell specifications
Cartridge Model AT-VM95E BK
Cartridge Type VM
Recommended load
impedance
47,000 ohms
Output voltage 4.0 mV (mV at 1 kHz, 5 cm/sec)
Stylus 0.3 × 0.7 mil bonded elliptical stylus
Cantilever Aluminum pipe
Tracking force range 1.8 to 2.2 g (standard 2.0 g)
Cartridge weight 6.1 g (0.22 oz)
Headshell model AT-HS4 BK
Headshell weight 8.5 g (excluding lead wires)
Headshell overhang
adjustment
± 5 mm
General specifications
Power supply requirements 100 to 240 V, 50/60 Hz, 0.5 A Max.
Power consumption 1.3 W
AC Adapter 12 V, 0.5 A
Dimensions 420 mm (16.54") × 340 mm (13.39")
× 126 mm (4.96") (W × D × H)
Weight 5.56 kg (12.25 lbs)
Accessories Dust cover, Rubber mat, Platter
(with drive belt),Dust cover hinges,
Counterweight, Headshell (AT-HS4 BK)
with VM stereo cartridge (AT-VM95E
BK), 45-RPM adapter, RCA audio
cable (Approx. 1.0 m (3.3')), AC
adapter (Approx. 1.5 m (4.9'))
Replacement stylus
(sold separately)
AT-VMN95E BK
Replacement headshell
(sold separately)
AT-HS4 BK
Replacement belt
(sold separately)
AT-LPW50PB exclusive belt
Specifications are subject to change without notice due to
improvements.
162502020-02-01 ver.1 2020.01.01
Audio-Technica Corporation
2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan
©2020 Audio-Technica Corporation
Global Support Contact: www.at-globalsupport.com