Specifications
1. Use only fresh alkaline batteries. Do not use “general
purpose” (carbon-zinc) batteries.
2. Position the receiver so that it has the fewest possible
obstructions between it and the normal location of the
transmitter. Line-of-sight is best.
3. The transmitter and the receiver must be set to the same
frequency. Set or change transmitter frequency only
when its power is turned off.
4. The transmitter and the receiver should be as close
together as conveniently possible, b
ut no less than six
feet (2 m.).
5. Yellow LED indicates the channel is set to service position
(0 or 9); please select a valid operating channel (1-8).
6. The receiver antennas should be kept away from any
metal.
7. A receiver cannot receive signals from two transmitters
at the same time.
8. If the AF Level control of the receiver is set too high, it
may over-drive the input of the mixer or clip the output of
the receiver, causing distortion. Conversely, if the receiver
output is set
too low, the overall signal-to-noise ratio of
the system may be reduced. Adjust the output level of
the receiver so the highest sound pressure level going
into the microphone (or the loudest instrument playing
level) causes no input overload in the mixer, and yet
permits the mixer level controls to operate in their
“normal” range (not set too high or too low). This
provides the optimum signal-to-noise for the entire system.
9. In the UniPak transmitter, the “Mic” or “Inst” in
put
control not in use should be set to minimum.
10. Turn the transmitter off when not in use. Remove the
battery if the transmitter is not to be used for a period of
time. Unplug the receiver from the AC outlet when the
system is not in use.
Ten T ips to Obtain the Best Results
For future reference, please record your system information here (the serial numbers appear inside the battery
compartment of each transmitter, and on the bottom of each receiver):
Receiver DR-R22 SN
UniPak™
Body-Pack DR-T250 S/N
Transmitter
Handheld Dynamic DR-T260 S/N
Microphone Transmitter
Audio -Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224 330/686-2600 www.audio-technica.com
P51869 ©2006 Audio-Technica U.S., Inc. Printed in U.S.A.
One-Year Limited Warranty
Audio-Technica professional wireless systems purchased in the U.S.A. are warranted for one year from date of purchase by Audio-Technica U.S., Inc.
( A . T. U. S . ) to be free of defects in materials and workmanship. In event of such defect, product will be repaired promptly without charge or, at our
option, replaced with a new product of equal or superior value if delivered to A. T. U. S . or an Authorized Service Center, prepaid, together with the sales
slip or other proof o
f purchase date. Prior approval from A.T. U . S . is required for return. This warranty excludes defects due to normal wear, abuse,
shipping damage, or failure to use product in accordance with the instructions. This warranty is void in the event of unauthorized repair or modifica-
tion, or removal or defacing of the product labeling.
For return approval and shipping information, contact the Service Dept., Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224.
Except to
the extent precluded by applicable state law, A .T. U . S . will have no liability for any consequential, incidental, or special damages; any
warranty of merchantability or fitness for particular purpose expires when this warranty expires.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
Outside the U.S.A., please contact your local dealer for warranty details.
Consumer Alert
Most users do not need a license to operate this wireless microphone system. Nevertheless, operating this microphone
system without a license is subject to certain restrictions: the system may not cause harmful interference; it must operate at
a low power level (not in excess of 50 milliwatts); and it has no protection from interference received from any other device.
Purchasers should also be aware that the FCC is currently evaluating use of wireless microphone systems, and these rules
are subject to change. For more information, call the FCC at 1-888- CALL-FCC (TTY: 1-888-TELL-FCC) or visit the FCC’s wireless
microphone website at www.fcc.gov/cgb/wirelessmicrophones
1. Use only fresh alkaline batteries. Do not use “general
purpose” (carbon-zinc) batteries.
2. Position the receiver so that it has the fewest possible
obstructions between it and the normal location of the
transmitter. Line-of-sight is best.
3. The transmitter and the receiver must be set to the same
frequency. Set or change transmitter frequency only
when its power is turned off.
4. The transmitter and the receiver should be as close
together as conveniently possible, b
ut no less than six
feet (2 m.).
5. Yellow LED indicates the channel is set to service position
(0 or 9); please select a valid operating channel (1-8).
6. The receiver antennas should be kept away from any
metal.
7. A receiver cannot receive signals from two transmitters
at the same time.
8. If the AF Level control of the receiver is set too high, it
may over-drive the input of the mixer or clip the output of
the receiver, causing distortion. Conversely, if the receiver
output is set
too low, the overall signal-to-noise ratio of
the system may be reduced. Adjust the output level of
the receiver so the highest sound pressure level going
into the microphone (or the loudest instrument playing
level) causes no input overload in the mixer, and yet
permits the mixer level controls to operate in their
“normal” range (not set too high or too low). This
provides the optimum signal-to-noise for the entire system.
9. In the UniPak transmitter, the “Mic” or “Inst” in
put
control not in use should be set to minimum.
10. Turn the transmitter off when not in use. Remove the
battery if the transmitter is not to be used for a period of
time. Unplug the receiver from the AC outlet when the
system is not in use.
Ten T ips to Obtain the Best Results
For future reference, please record your system information here (the serial numbers appear inside the battery
compartment of each transmitter, and on the bottom of each receiver):
Receiver DR-R22 SN
UniPak™
Body-Pack DR-T250 S/N
Transmitter
Handheld Dynamic DR-T260 S/N
Microphone Transmitter
Audio -Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224 330/686-2600 www.audio-technica.com
P51869 ©2006 Audio-Technica U.S., Inc. Printed in U.S.A.
One-Year Limited Warranty
Audio-Technica professional wireless systems purchased in the U.S.A. are warranted for one year from date of purchase by Audio-Technica U.S., Inc.
( A . T. U. S . ) to be free of defects in materials and workmanship. In event of such defect, product will be repaired promptly without charge or, at our
option, replaced with a new product of equal or superior value if delivered to A. T. U. S . or an Authorized Service Center, prepaid, together with the sales
slip or other proof o
f purchase date. Prior approval from A.T. U . S . is required for return. This warranty excludes defects due to normal wear, abuse,
shipping damage, or failure to use product in accordance with the instructions. This warranty is void in the event of unauthorized repair or modifica-
tion, or removal or defacing of the product labeling.
For return approval and shipping information, contact the Service Dept., Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224.
Except to
the extent precluded by applicable state law, A .T. U . S . will have no liability for any consequential, incidental, or special damages; any
warranty of merchantability or fitness for particular purpose expires when this warranty expires.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
Outside the U.S.A., please contact your local dealer for warranty details.
1. Use only fresh alkaline batteries. Do not use “general
purpose” (carbon-zinc) batteries.
2. Position the receiver so that it has the fewest possible
obstructions between it and the normal location of the
transmitter. Line-of-sight is best.
3. The transmitter and the receiver must be set to the same
frequency. Set or change transmitter frequency only
when its power is turned off.
4. The transmitter and the receiver should be as close
together as conveniently possible, b
ut no less than six
feet (2 m.).
5. Yellow LED indicates the channel is set to service position
(0 or 9); please select a valid operating channel (1-8).
6. The receiver antennas should be kept away from any
metal.
7. A receiver cannot receive signals from two transmitters
at the same time.
8. If the AF Level control of the receiver is set too high, it
may over-drive the input of the mixer or clip the output of
the receiver, causing distortion. Conversely, if the receiver
output is set
too low, the overall signal-to-noise ratio of
the system may be reduced. Adjust the output level of
the receiver so the highest sound pressure level going
into the microphone (or the loudest instrument playing
level) causes no input overload in the mixer, and yet
permits the mixer level controls to operate in their
“normal” range (not set too high or too low). This
provides the optimum signal-to-noise for the entire system.
9. In the UniPak transmitter, the “Mic” or “Inst” in
put
control not in use should be set to minimum.
10. Turn the transmitter off when not in use. Remove the
battery if the transmitter is not to be used for a period of
time. Unplug the receiver from the AC outlet when the
system is not in use.
Ten T ips to Obtain the Best Results
For future reference, please record your system information here (the serial numbers appear inside the battery
compartment of each transmitter, and on the bottom of each receiver):
Receiver DR-R22 SN
UniPak™ Body-Pack DR-T250 S/N
Transmitter
Handheld Dynamic DR-T260 S/N
Microphone Transmitter
Audio -Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224 330/686-2600 www.audio-technica.com
P51869 ©2006 Audio-Technica U.S., Inc. Printed in U.S.A.
One-Year Limited Warranty
Audio-Technica professional wireless systems purchased in the U.S.A. are warranted for one year from date of purchase by Audio-Technica U.S., Inc.
( A . T. U. S . ) to be free of defects in materials and workmanship. In event of such defect, product will be repaired promptly without charge or, at our
option, replaced with a new product of equal or superior value if delivered to A. T. U. S . or an Authorized Service Center, prepaid, together with the sales
slip or other proof o
f purchase date. Prior approval from A.T. U . S . is required for return. This warranty excludes defects due to normal wear, abuse,
shipping damage, or failure to use product in accordance with the instructions. This warranty is void in the event of unauthorized repair or modifica-
tion, or removal or defacing of the product labeling.
For return approval and shipping information, contact the Service Dept., Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224.
Except to
the extent precluded by applicable state law, A .T. U . S . will have no liability for any consequential, incidental, or special damages; any
warranty of merchantability or fitness for particular purpose expires when this warranty expires.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
Outside the U.S.A., please contact your local dealer for warranty details.
1. Use only fresh alkaline batteries. Do not use “general
purpose” (carbon-zinc) batteries.
2. Position the receiver so that it has the fewest possible
obstructions between it and the normal location of the
transmitter. Line-of-sight is best.
3. The transmitter and the receiver must be set to the same
frequency. Set or change transmitter frequency only
when its power is turned off.
4. The transmitter and the receiver should be as close
together as conveniently possible, b
ut no less than six
feet (2 m.).
5. Yellow LED indicates the channel is set to service position
(0 or 9); please select a valid operating channel (1-8).
6. The receiver antennas should be kept away from any
metal.
7. A receiver cannot receive signals from two transmitters
at the same time.
8. If the AF Level control of the receiver is set too high, it
may over-drive the input of the mixer or clip the output of
the receiver, causing distortion. Conversely, if the receiver
output is set
too low, the overall signal-to-noise ratio of
the system may be reduced. Adjust the output level of
the receiver so the highest sound pressure level going
into the microphone (or the loudest instrument playing
level) causes no input overload in the mixer, and yet
permits the mixer level controls to operate in their
“normal” range (not set too high or too low). This
provides the optimum signal-to-noise for the entire system.
9. In the UniPak transmitter, the “Mic” or “Inst” in
put
control not in use should be set to minimum.
10. Turn the transmitter off when not in use. Remove the
battery if the transmitter is not to be used for a period of
time. Unplug the receiver from the AC outlet when the
system is not in use.
Ten T ips to Obtain the Best Results
For future reference, please record your system information here (the serial numbers appear inside the battery
compartment of each transmitter, and on the bottom of each receiver):
Receiver DR-R22 SN
UniPak™
Body-Pack DR-T250 S/N
Transmitter
Handheld Dynamic DR-T260 S/N
Microphone Transmitter
Audio -Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224 330/686-2600 www.audio-technica.com
P51869 ©2006 Audio-Technica U.S., Inc. Printed in U.S.A.
One-Year Limited Warranty
Audio-Technica professional wireless systems purchased in the U.S.A. are warranted for one year from date of purchase by Audio-Technica U.S., Inc.
( A . T. U. S . ) to be free of defects in materials and workmanship. In event of such defect, product will be repaired promptly without charge or, at our
option, replaced with a new product of equal or superior value if delivered to A. T. U. S . or an Authorized Service Center, prepaid, together with the sales
slip or other proof o
f purchase date. Prior approval from A.T. U . S . is required for return. This warranty excludes defects due to normal wear, abuse,
shipping damage, or failure to use product in accordance with the instructions. This warranty is void in the event of unauthorized repair or modifica-
tion, or removal or defacing of the product labeling.
For return approval and shipping information, contact the Service Dept., Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224.
Except to
the extent precluded by applicable state law, A .T. U . S . will have no liability for any consequential, incidental, or special damages; any
warranty of merchantability or fitness for particular purpose expires when this warranty expires.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
Outside the U.S.A., please contact your local dealer for warranty details.