ENGLISH AXR85 AX R100 STEREO RECEIVER
Contents IMPORTANT SAFET Y INSTRUCTIONS 3 LIMITED WARR ANT Y 4 RE AR PANEL CONNECTIONS 5 FRONT PANEL CONTROL S 6 REMOTE CONTROL 7 This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form, without prior written permission of the manufacturer. All trademarks and registered trademarks are the property of their respective owners.
Important safety instructions For your own safety please read the following important safety instructions carefully before attempting to connect this unit to the mains power supply. They will also enable you to get the best performance from and prolong the life of the unit: 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings.
SERVICING These units are not user serviceable, never attempt to repair, disassemble or reconstruct the unit if there seems to be a problem. A serious electric shock could result if this precautionary measure is ignored. In the event of a problem or failure, please contact your dealer. FEDERAL COMMUNICATIONS COMMISSION Supplier’s declaration of conformity (SDoC) Equipment(s): Stereo Receiver Model(s): AXR85,AXR100 Trademark: Cambridge Audio This device complies with Part 15 of the FCC Rules.
Rear panel connections AM 300Ω FM 75Ω Loudspeaker Terminals D3 D1 8 A D3 MM Phono Rec Out A3 D2 A2 D1 7 AXR100 Stereo Receiver 10 A D2 5V 400mA 1 Designed & Engineered in Great Britain Assembled in China Impedance 4–8 ohms Right Service Port Left 6 Mains Voltage Selector Switch 115/220-230V~ 50/60Hz 11 Power AC 9 A1 Sub Out Ground A2 A1 A3 2 1 MM Phono Rec Out 3 4 B Ground B Right Sub Out 12 Left Max Power Consumption: 550W 5 DIGITAL INPUTS (AXR100 ONLY) 8 N
Front panel controls AX R100 7 11 9 1 2 3 4 FM / AM A1 / D1 A2 / D2 / PHONO SPEAKER A / B A3 / D3 5 MENU 8 MODE / STORE 1/6 2/7 3/8 4/9 5 / 10 10 VOLUME 12 AUX IN 6 1 STANDBY/ON Switches the unit between Standby mode (indicated by dim power LED) and On (indicated by bright power LED). Standby is a low power mode where the power consumption is less than 0.5 Watts. The unit can be left in Standby mode when not in use. This product has APD (Auto Power Down) enabled as default.
Remote control The AXR is supplied with a remote control that operates this unit and its built-in tuner. In addition, the buttons with Blue coloured icons can operate a matching AX CD player. Always use Alkaline batteries. CD STANDBY/ON Switches the unit between Standby mode and On. Mute 1 2 3 4 5 6 To operate the AXC players only. For more information refer to the AX CD user’s manual. 7 8 9 SPEAKER A/B 0 Prog Prog Clear Speaker A/B Stereo / Mono Mode Mutes audio on the unit.
Connections LOUDSPEAKERS Check the impedance of your speakers. When using a pair of speakers, you can use types with an impedance of between 4 and 8 Ohms. When using two pairs of speakers, you must use types with an impedance of 8 Ohms each, see later section. The red coloured speaker terminals are positive (+) and the black speaker terminals are negative (-). Make sure correct polarity is maintained at each speaker connector or the sound can become weak and “phasey” with little bass.
SPEAKER B CONNECTIONS The Speaker B connections on the back of the amplifier allow for a second set of speakers to be used (i.e. speakers located in another room). The Speaker A/B button on the front panel and remote control allows the two sets of speakers to be toggled on and off. Refer to the Front Panel or Remote Control section of this manual for more information on the Speaker A/B operation. Either A or B, or both A and B may be selected for use.
Aerials Operating instructions After making any connections to your unit, activate the AXR by pressing the Standby/On button on the front of the unit. SETTING THE SOURCE Press the Source button on the front of the unit corresponding to your desired source. Alternatively, you may use the appropriate button on the remote control. BLUETOOTH To.connect a Bluetooth device to AXR.
Repeatedly pressing the FM/AM button on the front of the unit switches between FM and AM modes. Note: For ease of tuning on first time use, we recommend that you set the AXR to ‘Auto’ mode. Press the Mode/Store button on the front of the unit. This button cycles through Preset, Auto and Manual, modes. TUNER SETTINGS It is possible to change the tuner region settings for this unit. This can be necessary if the unit has been moved to a different country.
Technical specifications AXR85 AXR100 Power output 100 watts (into 8Ω) THD (unweighted) <0.01% @ 1kHz, 80% of rated power <0.15% 20Hz - 20kHz, 80% of rated power Frequency response (-1dB) 5Hz - 50kHz Power output 85 watts (into 8Ω) THD (unweighted) <0.01% @ 1kHz, 80% of rated power <0.15% 20Hz - 20kHz, 80% of rated power Frequency response (-1dB) 5Hz - 50kHz S/N ratio (ref 1W) >82dB (unweighted) Input impedances 47k ohms Power Amp damping factor >50 Standby power consumption <0.5W Max.
Troubleshooting THERE IS NO POWER Ensure the AC power cord is connected securely. Ensure the plug is fully inserted into the wall socket and is switched on. Check fuse in the mains plug or adaptor. Check the power is on at the front of the unit. THERE IS NO SOUND Check the correct input is selected. Check that the speakers are connected correctly. If using the tuner, check aerial connections and an available station is selected. Check the unit is not in mute mode.
Gallery Court, Hankey Place London SE1 4BB United Kingdom Cambridge Audio is a brand of Audio Partnership Plc. Registered in England No.
