Users Manual For Odyssey Stratos, Khartago, Cyclops, Tempest, Candela product families.
A brief history and a short philosophical take: Rolf Gemein can easily be described as one of the true high end audio pioneers. As early as the mid – 70’s, he experimented with then revolutionary design aspects such as different internal cables, different types of solders, the influence of resonance control in the amplifier chassis, etc. In 1979, Rolf started Symphonic Line with the intention of being solely responsible for the quest of the perfect musical “illusion “.
Before operating your Odyssey unit, please take the time and carefully read all safety instructions and the entire owner's manual. You'll be given not only information about safety concerns and technical specifications, but also advice as how to optimize your system sonically, as well as information of our efforts to create the single best value in the high end audio market today.
Welcome Thank you for purchasing a product from Odyssey Designs. Your Odyssey unit has been designed by Symphonic Line in Germany. In 1979, Rolf Gemein started Symphonic Line with the intention of creating the perfect musical “illusion”. In the years since, his incredible talents and complete devotion to music produced phenomenal international successes as borne out by dozens of product - of- the - year, consumer, and best - at - show awards.
Safety Instructions 1. Casework: Do not operate the unit without the outer casework, internal electrical voltages of the unit may cause serious injuries 2. Fuses: Do not bypass any fuse in the unit. Only replace the fuses with the same type and ratings. 3. Power Requirements: An audiophile quality power cord with a three - prong plug is included with your Odyssey unit. To prevent shock hazards, do not defeat the grounding plug.
Quality Information The trademark of Odyssey and Symphonic Line products is uncompromising ultra – high end performance. Manual assembly and exclusive hand - soldering on all contacts surely enhances the performance aspect. Your Odyssey product has been mostly hand -made. This aspect of the manufacturing process is very expensive and time consuming, but ultimately, yields the best possible returns in high performance sound qualities. However, with manual labor comes the added danger of human errors.
Unpacking Please inspect your unit immediately for any possible shipping damages. Pay special attention to the glass inserts within the front plate. They should inspected for any cracks. Immediately report any damage to your authorized Odyssey dealer, the shipping company, or Odyssey Design Group. Please keep the shipping materials in a safe place for possible future reuse. Location 1. Your Odyssey unit can be installed on a shelf, table, or equipment stand. Since the Tempest weighs in at around 35 lbs.
Tempest preamplifier connection to Stratos Stereo power amplifier Stratos Stereo power amplifier connection to Tempest preamplifier
Tempest preamplifier connection to Stratos Mono power amplifier Stratos Mono power amplifier connection to Tempest preamplifier
Tempest preamplifier connection to Khartago Stereo power amplifier Khartago Stereo power amplifier connection to Tempest preamplifier
Tempest preamplifier connection to Khartago Mono power amplifier Khartago Mono power amplifier connection to Tempest preamplifier
Cyclops integrated amplifier source connection
Tempest preamplifier: Basic hook up and operation: ● ● ● ● ● ● Tempest front panel: Big knob at left is turn on/off switch. Do not force it to go beyond when a soft click takes place. Then unit is on (approximately a 9:00 position) or backwards is in off position (approximately a 7:00 position). Big knob at right is volume control. Small central knobs are for input source control: Select and Monitor.
Warm - up Operation The following and it's related pages are intended as a general reference to the proper setup and operation of audio equipment. Every single audio and video system, Odyssey or other brands, benefit from these simple steps, some of which are actually free and very effective.
To realize ultimate performance of your audio system, fine-tuned adjustments or "tweaking" should be considered. This can involve everything from simply setting up the equipment properly to using expensive system-enhancing products and acoustical room treatments. We will attempt to categorize by cost the various options and provide some basic advice on optimizing system performance.
No cost tweaks The simplest, most cost-effective measure to the most out of your audio system is to set up the system properly. The following offers some advice on set-up: a. Component Placement: Place all of your components on as solid a surface as possible. The heavier and sturdier the foundation, the better. This usually means a solid equipment rack that is spiked into the carpet or that sits squarely on the floor with no wobble. If preferred, you can also locate the amplifier on the floor.
Low cost tweaks a. De-coupling devices: Cones, spikes, or dampers nearly always help to improve the performance of components and the sound of your system. This is why all Odyssey products are outfitted with $30 Audio Selection™ dampers as standard equipment, instead of cheaper glued-on rubber feet that are ineffective. We can also provide several different cones and spikes from Audio Selection™ to you, factory direct, with 50% savings. b.
Care and Maintenance Other than the internal fuses, there are no user serviceable parts inside your Odyssey amplifier or preamplifier. Thus, the top cover should only be opened for checking these fuses. Any other check up and work should be left to authorized service personnel. As for checking and changing internal fuses, see Always turn off the unit before opening the top cover. Your Odyssey case is made of brushed aluminum.
Trouble Shooting Should your Odyssey unit fail to operate at any time while switched on, please check the following points carefully: 1. Check for proper power connection. 2. Switch off your Odyssey unit and check for proper connection of all input and output wires. 3. If all cables are connected properly, check the proper power connection on all of your other components. 4. Turn on your Odyssey unit, and check the on / off switch.
Stratos Stereo power amplifiers family Specifications Stratos Stereo: base model specifications: ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 2 x 150 Watts RMS @ 8 Ohms 2 Ohm load stable Class A/AB 2 - 400,000 Hz frequency range 60,000µF memory 45 amps current delivery <0.
Stratos Mono power amplifiers family Specifications Stratos Mono: specifications per unit: ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 1 x 180 Watts RMS @ 8 Ohms (each) 2 Ohm load stable Class A/AB 1 - 600,000 Hz frequency range 120,000µF memory (each) 120 amps current delivery <0.
Khartago Stereo power amplifiers family Specifications Khartago Stereo: base model specifications: ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 2 x 130 Watts RMS @ 8 Ohms 2 Ohm load stable Class A/AB 2 - 400,000 Hz frequency range 60,000µF memory 40 amps current delivery <0.
Khartago Mono power amplifiers family Specifications Khartago Mono: specifications per unit: ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 1 x 150 Watts RMS @ 8 Ohms (each) 2 Ohm load stable Class A/AB 1 - 600,000 Hz frequency range 120,000µF memory (each) 120 amps current delivery <0.
Cyclops integrated amplifiers family Specifications Cyclops integrated amplifier: base model specifications: ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● Minimalist design, 1 input only 2 x 130 Watts RMS @ 8 Ohms 2 Ohm load stable Class A/AB 2 - 400,000 Hz frequency range 60,000µF memory 40 amps current delivery <0.
Tempest SLB line and phono preamplifier family Specifications Tempest SLB: model specifications: ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● SLB: Genuine Symphonic Line® (circuit) board 5 - 200,000 Hz frequency range 14,000µF memory <0.
Candela vacuum tube line preamplifier Specifications Candela: model specifications: ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● “Current Source Loaded Grounded Cathode Amplifier" based design Vacuum Tube single ended stages Class-A single ended configuration Zero feedback Low output impedance Low current design Relay-controlled input selector Power supply rectification using ultra fast-soft recovery “Stealth” Diodes (2) ECC82/12AU7 tubes 14dB gain Frequency Response 10Hz - 500kHz RCA type inputs & output
Loudspeakers Specifications Lorelei: model specifications: ● ● ● ● ● ● ● ● ● ● ● ● ● ● Design drivated from Symphonic Line's® Legato 2-way Ported 32-22,000 Hz frequency range 6 Ohm impedance 89 dB sensitivity Scanspeak D2905-970000 tweeter: 1" dome, low compression design, non resonant chamber Scanspeak 18W/8545-00 midwoofer: 6.
Conditions of Warranty Terms and Conditions 1.Limited Warranty: Odyssey Designs warrants your unit to be free from manufacturing defects subject to the conditions hereinafter set forth for a period of 20 (twenty) years from the date of purchase. 2 Conditions: This warranty is subject to the following conditions and limitations: ● ● ● ● ● Return of the supplied warranty registration paper within 30 days of purchase or fill the online form.
